Rudder Angle Indicator
A rudder angle indicator reports where the rudder actually is, taken from a sensor at the rudder stock itself, which is why SOLAS keeps it functionally independent of the steering control system — a helm order indicator only shows what was commanded, not what the rudder is doing.
What to check on a Rudder Angle Indicator.
14 models from Sperry Marine in Rudder Angle Indicator. Below: the full model list.
What sets this instrument apart
Bridge teams often conflate two different readings. A helm order or wheel repeater shows the angle the helmsman or autopilot has commanded, taken from the steering control handle or the autopilot's output. A rudder angle indicator (RAI) shows the angle the rudder blade has actually reached, taken from a sensor mounted at the rudder stock or tiller in the steering gear compartment. The two normally agree, but a fault anywhere in the steering gear — a hydraulic ram not following its valve, a mechanical linkage failure, a telemotor fault — will show up as a gap between commanded and actual angle, and only the RAI, reading directly off the stock, can reveal that gap.
Legend
- rudder stock
- bridge repeater dial
- signal cable
- angle transmitter (at rudder stock)
- PORT
- STBD
Main components
Rudder angle transmitter
Mounted on the rudder stock or the tiller arm itself, this is either a mechanical linkage driving a synchro transmitter or, on newer installations, an inductive or magnetic sensor reading stock rotation directly, avoiding a mechanical linkage that can wear or seize.
Signal transmission
The signal reaches the bridge as a synchro/analogue feed on older ships or as a digital NMEA feed on integrated bridge systems, and is usually also fed to the steering gear compartment's own local repeater so engineers working there can see the same reading as the bridge.
Read the full guide
Bridge display
At least one repeater is positioned so it is visible from the conning position, with a second commonly fitted at the steering position itself.
Regulations and class
SOLAS Chapter V regulation 19 requires a rudder angle indicator that is functionally independent of the steering control system, so that a fault in the autopilot or helm control cannot also blind the bridge to actual rudder position. Class surveys the steering gear including a function test of the RAI as part of periodic steering gear trials, checking that the indicated angle matches the rudder's true position at both hard-over limits and amidships.
Typical faults
| Fault | Consequence |
|---|---|
| Mechanical linkage wear on an older transmitter | Indicated angle drifts from actual angle by a growing offset, most noticeable near the rudder limits |
| Synchro transmitter failure | Indicator freezes on a fixed reading while the rudder continues to move, giving the bridge false confidence |
| Calibration not re-checked after steering gear overhaul | Zero point shifted, so amidships on the rudder no longer reads zero on the indicator |
| Cable or connector corrosion in the steering gear compartment | Intermittent or erratic reading in a compartment that is often warm, humid and hard to keep dry |
What to look for in a supplier
- Transmitter type matched to the existing steering gear's stock or tiller geometry, rotary or linear as fitted
- Enclosure rating suited to a steering flat environment rather than a bridge-console-grade unit
- Output format compatible with the ship's integrated bridge or autopilot interface without an added converter
- Straightforward field calibration procedure, since this is checked at every steering gear test
Before departure, compare the RAI reading against the rudder visually amidships if it can be seen, or against the steering gear compartment's local gauge; a discrepancy here is one of the more reliable early signs of a developing helm-order chain fault, well before it shows up as a steering casualty.
Models in this type.
The best-documented model of each manufacturer first, then the next — 14 of 14 models in Rudder Angle Indicator. Every row links to full specifications, documents and service notes.
Manufacturers.
All 26 manufacturers with models of Rudder Angle Indicator. Names with a manufacturer page open it; the others open a search across the full library.
All manufacturers in the libraryAlso in Navigation & Bridge Equipment.
The other equipment types in this category.
Write to us about this model — the answer comes by e-mail.
Name the make and the model and what the job is: a spare, a service call, a second opinion on a data sheet. We answer by e-mail.
No details at hand? A photo of the rating plate or the part is enough — simply attach it to the request.
Questions that come up with this equipment.
Is Rudder Angle Indicator data free?
Yes. Every model page, every guide and every datasheet for this type is readable without an account. An account adds saved searches and requests, nothing is taken away.
My model is missing — what now?
Send us the nameplate. We identify it by hand, add it to the library, and if you need a part or a service, the request is already on our desk.
Can you source a Rudder Angle Indicator part?
Yes. Tell us the manufacturer, the model and what you need — a person reads every request and replies by e-mail.