Echo Sounder
A single-beam echo sounder gives one number: depth under the transducer. Multibeam sweeps a fan of beams across the track and builds a swath, which is why hydrographic survey vessels carry multibeam and merchant ships carry single beam.
What to check on an Echo Sounder.
22 models from Simrad in Echo Sounder. Below: the full model list.
What sets an echo sounder apart from other depth instruments
An echo sounder measures depth by timing the return of an acoustic pulse from a transducer mounted in the hull to the seabed and back. The instrument does not measure position or speed; it only reports the water column beneath (or, for multibeam, beside) the ship. On a merchant vessel the transducer is usually a single-beam unit sending one narrow vertical pulse, reporting one depth value. A multibeam echo sounder fires a fan of beams across the ship's track in a single ping, producing a swath of depth points instead of a line. That difference in beam geometry is what separates a bridge navigation instrument from a hydrographic survey tool, even though both work on the same time-of-flight principle.
Main components
Transducer
Piezoelectric element in a sea chest or hull fitting, below the waterline, often with a retractable fairing so it can be serviced without dry-docking on larger ships.
Transceiver / transmitter-receiver unit
Generates the excitation pulse, amplifies the return echo, and passes a digitised signal to the processing unit.
Read the full guide
Display and processing unit
Shows depth as a numeric readout and/or a scrolling depth trace, and on SOLAS-class units drives an audible/visual shallow-water alarm.
Keel offset and draught correction
Set at commissioning so the reported figure matches depth below keel, below transducer, or below the waterline, whichever the operator has selected — a frequent source of confusion during pilotage.
Selection and sizing
- Operating frequency: high frequency (150-200 kHz) for coastal and harbour work with fine resolution in shallow water; low frequency (10-50 kHz) for deep-sea sounding where high frequency signals attenuate before reaching the bottom.
- Maximum sounding depth required for the trade the ship runs in.
- Single beam versus multibeam — multibeam is only justified where swath coverage is the actual deliverable, such as dredging support or survey work, not general navigation.
- Integration: NMEA output to the ECDIS and VDR, since a standalone display with no data output no longer meets modern bridge integration expectations.
Regulations and class
SOLAS Chapter V, Regulation 19, requires an echo sounding device on ships of specified sizes as part of the mandatory navigational equipment carriage requirements. Class societies survey the unit as part of the periodic navigation equipment survey, checking calibration against a known depth and confirming alarm function. There is no IMO type-approval regime specific to echo sounders in the way there is for GMDSS equipment, but the transducer installation itself is often subject to class approval of the hull penetration.
Typical faults
| Fault | Cause | Consequence |
|---|---|---|
| Erratic or dropped depth readings | Aeration under the transducer from hull fouling, cavitation, or heavy pitching in ballast condition | Officer of the watch loses confidence in the display and may miss a genuine shoaling alarm |
| Fixed offset error | Draught correction left at the yard commissioning value after a change of loading condition | Reported depth below keel is wrong by the amount of the draught change, most dangerous when fully loaded |
| No signal / blank display | Transducer cable chafe or corrosion at the hull gland, common on older steel hulls | Total loss of depth information, forcing reliance on chart depth alone |
| Ghost bottom / second echo | Signal bouncing off the thermocline or a dense plankton layer | False shallow reading that can trigger unnecessary alarms or, worse, mask the real bottom return |
What to look for in a supplier
- Type approval certificate covering the specific SOLAS carriage requirement, not just a generic marine mark.
- Availability of a retractable transducer fairing if the ship needs to service the unit afloat.
- Documented NMEA 0183/2000 output list matching what the ECDIS and VDR actually require.
- Spares support for the transducer specifically, since it is the component most likely to need replacement after grounding contact or cavitation damage.
Check the draught correction setting every time the loading condition changes materially — a depth-below-keel reading that was accurate light-loaded can be dangerously optimistic once the ship is down to her marks.
Models in this type.
The best-documented model of each manufacturer first, then the next — 22 of 22 models in Echo Sounder. Every row links to full specifications, documents and service notes.
Manufacturers.
All 49 manufacturers with models of Echo Sounder. Names with a manufacturer page open it; the others open a search across the full library.
All manufacturersShow all 49 manufacturers
Also in Navigation & Bridge Equipment.
The other equipment types in this category.
One request. A person reads it and replies by e-mail.
Tell us the manufacturer, the model and what you need — a part, a service call, a second opinion. A person reads every request and replies by e-mail.
No details at hand? A photo of the rating plate or the part is enough — simply attach it to the request.
Three things people ask first.
Is Echo Sounder data free?
Yes. Every model page, every guide and every datasheet for this type is readable without an account. An account adds saved searches and requests, nothing is taken away.
My model is missing — what now?
Send us the nameplate. We identify it by hand, add it to the library, and if you need a part or a service, the request is already on our desk.
Can you source a Echo Sounder part?
Yes. Tell us the manufacturer, the model and what you need — a person reads every request and replies by e-mail.