Heading Repeater / Compass Repeater
A heading repeater carries no gyroscope of its own; it is a slave display driven by the master gyrocompass, and its only job is to put a true heading in front of the helmsman, the pelorus and the wing lookout at the same moment.
What to check on a Heading Repeater / Compass Repeater.
1 models from Furuno Electric in Heading Repeater / Compass Repeater. Below: the full model list.
What makes this type
A heading or compass repeater is a slave indicator that reproduces the heading generated by the master gyrocompass, not an independent sensor. This distinguishes it from the gyrocompass itself, which does the actual sensing, and from a magnetic compass, which is a standalone backup instrument. Repeaters exist because a single gyrocompass, usually mounted low in the ship for stability, cannot be read directly from the helm, the bridge wings or a pelorus stand, so its output is electrically or optically transmitted to multiple repeater positions around the vessel.
Main components
Repeater display unit
A dial or digital readout, at the steering position, chart table, bridge wings and often on the monkey island for taking visual bearings. Older systems use a synchro or stepper motor driven directly by the gyrocompass transmission; modern systems distribute heading digitally over a serial or network bus and drive each repeater electronically.
Transmission system
The wiring or network link between master gyrocompass and each repeater. In legacy synchro systems this is a dedicated multi-core cable per repeater; in networked systems a single bus can feed many repeaters, simplifying retrofit but concentrating failure risk on the bus itself.
Read the full guide
Pelorus and bearing ring
Wing repeaters are commonly fitted with a pelorus ring for taking visual and radar bearings referenced to true heading, a function the bridge relies on for position fixing by terrestrial bearings.
Selection and sizing
- Compatibility with the ship's existing gyrocompass output format, synchro, step, or serial/network
- Number and location of repeater positions required by the ship's bridge layout and SOLAS carriage requirements
- Illumination and readability under both daylight and night bridge lighting conditions
- Backup power arrangement, since a repeater that goes dark on a power transfer defeats its purpose at the exact moment it may be needed
Regulations and class
SOLAS Chapter V requires ships above specified tonnage thresholds to be fitted with a gyrocompass and heading repeaters at the main steering position and, depending on ship type, at the bearing positions used for taking visual and radar bearings. Class societies verify repeater installation and function as part of the navigation equipment survey alongside the master gyrocompass itself.
Typical faults
| Fault | Consequence |
|---|---|
| Repeater heading drifting from master gyro reading | Helmsman steering to a wrong reference, and bearings taken at the wing repeater offset from true |
| Synchro motor wear on legacy systems | Sticking or lagging display, especially noticeable during rapid course changes |
| Corroded wing repeater housing from salt exposure | Intermittent display or complete failure at the exposed bearing position |
| Bus failure on networked repeater systems | Simultaneous loss of multiple repeaters rather than a single unit, a wider outage than legacy wiring would produce |
What to look for in a supplier
- Confirmed compatibility with the ship's specific gyrocompass output protocol before ordering a replacement or additional repeater
- Housing rated for exposed bridge wing conditions if the unit is destined for that position
- Spare parts availability for legacy synchro systems still common on older tonnage
Compare every wing repeater against the master gyro reading during the daily bridge equipment check, not just at survey time; a slow drift is easy to miss until a bearing taken from the wing is visibly wrong.
Models in this type.
The best-documented model of each manufacturer first, then the next — 1 of 1 models in Heading Repeater / Compass Repeater. Every row links to full specifications, documents and service notes.
Manufacturers.
All 12 manufacturers with models of Heading Repeater / Compass Repeater. Names with a manufacturer page open it; the others open a search across the full library.
All manufacturersAlso in Navigation & Bridge Equipment.
The other equipment types in this category.
One request. A person reads it and replies by e-mail.
Tell us the manufacturer, the model and what you need — a part, a service call, a second opinion. A person reads every request and replies by e-mail.
No details at hand? A photo of the rating plate or the part is enough — simply attach it to the request.
Three things people ask first.
Is Heading Repeater / Compass Repeater data free?
Yes. Every model page, every guide and every datasheet for this type is readable without an account. An account adds saved searches and requests, nothing is taken away.
My model is missing — what now?
Send us the nameplate. We identify it by hand, add it to the library, and if you need a part or a service, the request is already on our desk.
Can you source a Heading Repeater / Compass Repeater part?
Yes. Tell us the manufacturer, the model and what you need — a person reads every request and replies by e-mail.