Skip to content
OceanSphereENGINES
Library› Engine Room› Heat Exchangers› Plate Heat Exchanger
Heat Exchangers

Plate Heat Exchanger

A plate heat exchanger stacks thin corrugated plates to pack far more heat transfer area into a given footprint than a shell-and-tube unit of the same duty, at the cost of being far more sensitive to gasket condition and fouling between the narrow plate gaps.

Alfa Laval
Knowledge

What to check on a Plate Heat Exchanger.

756 models from Alfa Laval in Plate Heat Exchanger. Below: the full model list.

What sets a plate heat exchanger apart

A plate heat exchanger builds its heat transfer surface from a stack of thin, corrugated metal plates clamped together (gasketed type) or permanently bonded (brazed or fully welded type), with hot and cold fluid running in alternating narrow channels between them. Compared with a shell-and-tube exchanger of the same duty, the plate design packs several times more surface area into the same volume because the corrugation pattern creates turbulence at low flow velocity, which improves heat transfer without needing long tube runs. The trade-off is channel width: gaps between plates are typically only a few millimetres, so the design is far less tolerant of solids, scale or fibrous debris than a tube bundle, and a gasketed unit depends entirely on gasket condition to stay leak-tight between the plate pack and between the fluid circuits.

Plate heat exchanger, plate pack arrangement
Cutaway of a gasketed plate heat exchanger: the fixed frame plate carries the four ports, the pack of corrugated plates is clamped by tie bolts against the movable pressure plate, gaskets seal each channel, and hot and cold fluid run in counter-flow through alternate channels.

Legend

  1. Tie bolts
  2. Plate pack (corrugated plates)
  3. Gasket (channel seal)
  4. Hot fluid in
  5. Cold fluid out
  6. Pressure plate (movable)
  7. Cold fluid in
  8. Hot fluid out
  9. Frame plate (fixed)
  10. Counter-flow channels

Main components

Plate pack

Pressed stainless steel or titanium plates with a herringbone or chevron corrugation pattern that sets the flow path and turbulence level; plate thickness and corrugation depth are chosen for the pressure and duty.

Gaskets (gasketed type)

Elastomer gaskets, glued or clip-fitted into a groove around each plate, seal the fluid channels and route flow between ports. Gasket material (NBR, EPDM, Viton) is selected for the fluid and temperature; the wrong gasket compound in a fuel or lube oil circuit degrades quickly.

Read the full guide

Frame, carrying bar and tightening bolts

The frame clamps the plate pack to a specified compressed thickness; under-tightening lets gaskets leak, over-tightening deforms plates and shortens gasket life.

Brazed or welded pack (compact type)

Copper-brazed or fully welded plate packs eliminate gaskets entirely, giving a smaller, higher-pressure-rated unit that cannot be opened for mechanical cleaning, only backflushed or chemically cleaned.

Selection and sizing

  • Duty and approach temperature - the closer the required approach temperature between the two fluids, the more plates or the larger the area needed.
  • Pressure rating - gasketed units typically handle up to around 25 bar; brazed and welded types reach substantially higher.
  • Fouling tendency of the fluid - seawater cooling duty favours a gasketed, openable design for periodic mechanical cleaning; clean closed-loop duty suits brazed units.
  • Materials - titanium plates for raw seawater service resist chloride pitting far better than stainless steel.
  • Connection size and plate count - determines physical footprint against available engine room space.

Regulations and class

Plate heat exchangers used in essential services (main engine cooling, fuel heating for combustion) fall under the class society's pressure vessel and piping rules for design pressure, material certification and pressure testing before delivery. Where the exchanger separates a fuel or lube system from a cooling water system, class rules typically require the design to prevent internal cross-contamination or to allow leak detection between circuits, since a failed plate or gasket can let fuel into cooling water or vice versa. There is no IMO convention specific to the plate exchanger type itself; requirements come through the classification society's machinery rules for the system the exchanger is part of.

Typical faults

FaultConsequence
Gasket hardening or shrinkage with ageinter-plate leakage, cross-contamination between fluid circuits
Fouling/scaling in narrow channelsrising pressure drop and falling heat transfer, often mistaken for pump wear
Plate corrosion pitting (wrong material for seawater)through-wall leaks, seawater ingress into the clean circuit
Incorrect re-assembly after opening for cleaningplates out of sequence change the flow path and duty is lost even though the unit looks intact

What to look for in a supplier

  • Material certificates for plates matching the actual fluid, especially titanium confirmation for seawater duty.
  • Gasket compound datasheet matching the fluid and maximum operating temperature, not a generic default.
  • Availability of individual replacement plates and gaskets for the exact plate pattern, since plate packs are not interchangeable between makers.

Before reassembling a gasketed plate exchanger after cleaning, check the plates go back in the original sequence and orientation - a swapped plate changes the flow pattern and the unit can look assembled correctly while badly underperforming.

Models

Models in this type.

The best-documented model of each manufacturer first, then the next — 100 of 756 models in Plate Heat Exchanger. Every row links to full specifications, documents and service notes.

Page 1 of 8 · Next →
Showing only Alfa Laval. Show all manufacturers
Alfa LavalAalborg Exhaust Gas Economiser 200-15,000 kW thermal Alfa Laval Golbey SASTBF 1225 V1 Alfa Laval LundT8-FM Alfa LavalM10-BFG 8.0 m² surface Alfa Laval Golbey SASTBF-1800 VX Alfa LavalM15-BFG 20.0 m² surface Alfa Laval Golbey SASTBF-350 VX Alfa LavalM20-MFG 50.0 m² surface Alfa LavalM3-FG 0.5 m² surface Alfa LavalM6-FG 2.0 m² surface Alfa LavalT20-BFG 30.0 m² surface Alfa LavalT50-MFG 100.0 m² surface Alfa LavalTL10-BFG 12.0 m² surface Alfa LavalAlfaNova Fusion-Bonded 10-1,000 kW thermal Alfa LavalCB Series (Brazed Plate) 5-500 kW thermal Alfa LavalM-Series Gasketed Plate Heat Exchanger 50-10,000 kW thermal Alfa LavalM10-MFG 50-500 kW Alfa LavalT5-MFG 20-200 kW Alfa Laval76 / HP 76 Alfa LavalAC10 Alfa LavalAC10-MAX Alfa LavalAC1000 Alfa LavalAC1000-MAX Alfa LavalAC112 Alfa LavalAC112-MAX Alfa LavalAC120 Alfa LavalAC120-MAX Alfa LavalAC16 Alfa LavalAC16-MAX Alfa LavalAC18 Alfa LavalAC18-MAX Alfa LavalAC220 Alfa LavalAC220-MAX Alfa LavalAC230 Alfa LavalAC230-MAX Alfa LavalAC232 Alfa LavalAC232-MAX Alfa LavalAC30 Alfa LavalAC30-MAX Alfa LavalAC300 Alfa LavalAC300-MAX Alfa LavalAC32 Alfa LavalAC32-MAX Alfa LavalAC400 Alfa LavalAC400-MAX Alfa LavalAC400-W Alfa LavalAC500 Alfa LavalAC500-MAX Alfa LavalAC502 Alfa LavalAC502-MAX Alfa LavalAC540 Alfa LavalAC540-MAX Alfa LavalAC600 Alfa LavalAC600-MAX Alfa LavalAC65 Alfa LavalAC65-MAX Alfa LavalAC70 Alfa LavalAC70-MAX Alfa LavalAC700 Alfa LavalAC700-MAX Alfa LavalAC75 Alfa LavalAC75-MAX Alfa LavalAC800 Alfa LavalAC800-MAX Alfa LavalAC800-W Alfa LavalAC90 Alfa LavalAC90-MAX Alfa LavalAC900 Alfa LavalAC900-MAX Alfa LavalACH230 Alfa LavalACH230-120P Alfa LavalACH230-150P Alfa LavalACH230-180P Alfa LavalACH230-30P Alfa LavalACH230-60P Alfa LavalACH230-90P Alfa LavalACH230-MAX Alfa LavalACH30 Alfa LavalACH30-120P Alfa LavalACH30-150P Alfa LavalACH30-180P Alfa LavalACH30-30P Alfa LavalACH30-60P Alfa LavalACH30-90P Alfa LavalACH30-MAX Alfa LavalACH500 Alfa LavalACH500-120P Alfa LavalACH500-150P Alfa LavalACH500-180P Alfa LavalACH500-30P Alfa LavalACH500-60P Alfa LavalACH500-90P Alfa LavalACH500-MAX Alfa LavalACH70 Alfa LavalACH70-120P Alfa LavalACH70-150P Alfa LavalACH70-180P Alfa LavalACH70-30P Alfa LavalACH70-60P Alfa LavalACH70-90P
More than the data sheet shows

Write to us about your machine — the answer comes by e-mail.

Name the make and the model and what the job is: a spare, a service call, a second opinion on a data sheet. We answer by e-mail.

No details at hand? A photo of the rating plate or the part is enough — simply attach it to the request.

Frequently asked

Questions that come up with this equipment.

Is Plate Heat Exchanger data free?

Yes. Every model page, every guide and every datasheet for this type is readable without an account. An account adds saved searches and requests, nothing is taken away.

My model is missing — what now?

Send us the nameplate. We identify it by hand, add it to the library, and if you need a part or a service, the request is already on our desk.

Can you source a Plate Heat Exchanger part?

Yes. Tell us the manufacturer, the model and what you need — a person reads every request and replies by e-mail.