Skip to content
OceanSphereENGINES
Library› Engine Room› Pumps› HT/LT Cooling Water Pump
Pumps

HT/LT Cooling Water Pump

HT and LT pumps move fresh water, not seawater, around the two closed cooling loops that protect the main engine: the high-temperature circuit that jackets the cylinders, and the low-temperature circuit that cools charge air and lube oil, each running against different pressure and temperature targets.

MAN Energy Solutions
Knowledge

What to check on a HT/LT Cooling Water Pump.

4 models from MAN Energy Solutions in HT/LT Cooling Water Pump. Below: the full model list.

What sets HT/LT pumps apart from other engine room pumps

The high-temperature (HT) circuit carries fresh water through the cylinder jackets and cylinder head cooling spaces of the main and auxiliary engines, running at 70-90°C on most medium and slow-speed diesels, and rejects its heat to the LT circuit or directly to the fresh water generator. The low-temperature (LT) circuit runs cooler, typically 30-40°C after seawater cooling, and serves the charge air cooler, lube oil cooler and sometimes the HT circuit's own heat exchanger. Both are centrifugal pumps running on closed, treated fresh water rather than raw seawater, which is what separates them from the seawater cooling pumps upstream - closed circuit water is chemically dosed against corrosion and scale, so these pumps see a far more benign fluid than a seawater pump does, but the consequence of a leak is loss of treated inventory rather than just lost suction.

Centrifugal cooling water pump, sectioned
Sectioned view of a centrifugal fresh-water pump showing the axial suction inlet, impeller inside the volute casing, tangential discharge outlet, shaft, mechanical seal, bearing bracket and coupling to the driving motor; this pump type is fitted in both the HT and LT cooling circuits.

Legend

  1. discharge outlet
  2. suction inlet
  3. impeller
  4. bearing bracket
  5. mechanical seal
  6. coupling to motor
  7. volute casing

Main components

  • Pump casing and impeller - centrifugal, single or multi-stage depending on required head, usually bronze or cast iron wetted parts since the fluid is non-corrosive fresh water.
  • Mechanical seal or gland packing - the most common source of visible leakage, particularly on older packed-gland designs.
  • Electric motor drive - most HT/LT pumps are motor-driven rather than engine-driven, allowing independent operation and standby duty.
  • Non-return and isolating valves - allow a standby pump to be brought online without draining the circuit.
  • Expansion tank connection - each circuit has a header/expansion tank that accommodates thermal expansion and provides the static head the pump suction needs.

Selection / Sizing

Pump capacity is set by the engine manufacturer's specified cooling water flow rate at rated output, expressed in m³/h, with head determined by the circuit's total resistance including the heat exchangers, engine water jackets and piping runs. HT and LT pumps are normally sized identically to their duty pump as a 100% standby, arranged so either pump can be started manually or automatically on a pressure-drop signal. Motor rating follows directly from the flow/head duty point on the pump curve; oversizing wastes electrical power continuously since these pumps run for the entire time the engine runs.

Regulations / Class

Class rules require engine cooling water systems to include standby pumping capacity capable of maintaining cooling if the duty pump fails, consistent with SOLAS Ch. II-1 requirements for essential machinery redundancy. Automatic standby pump start on low pressure is commonly a class notation requirement for unmanned machinery space (UMS) operation. There is no dedicated international convention specific to HT/LT pumps beyond these general machinery redundancy and periodic survey requirements.

Read the full guide

Typical faults

FaultConsequence
Mechanical seal wear or gland packing leakageGradual loss of circuit water, falling expansion tank level, air ingress
Impeller wear or erosionFalling flow and pressure, engine temperatures creeping up under load
Bearing failure from inadequate lubrication or misalignmentVibration, noise, eventual seizure and unplanned pump stoppage
Air lock in the circuit after maintenancePump loses prime or cavitates, poor circulation despite pump running
Standby pump not tested regularlyFails to start automatically when needed, defeating the redundancy it exists for

What to look for in a supplier

  • Pump curves matched precisely to the engine maker's specified duty point, not a generic nearest-fit selection.
  • Seal type compatible with the treated water chemistry already in use on board.
  • Spare parts commonality with other cooling pumps already carried, to reduce the spare parts inventory.
  • Documented bearing life and lubrication interval so maintenance planning can be scheduled realistically.

A slowly falling expansion tank level with no visible leak is almost always a gland or mechanical seal weeping into the bilge - trace it before it becomes a running loss that masks a real cooling water shortage under load.

Models

Models in this type.

The best-documented model of each manufacturer first, then the next — 4 of 4 models in HT/LT Cooling Water Pump. Every row links to full specifications, documents and service notes.

Showing only MAN Energy Solutions. Show all manufacturers
By manufacturer

Manufacturers.

All 5 manufacturers with models of HT/LT Cooling Water Pump. Names with a manufacturer page open it; the others open a search across the full library.

All manufacturers in the library
More than the data sheet shows

Write to us about your machine — the answer comes by e-mail.

Name the make and the model and what the job is: a spare, a service call, a second opinion on a data sheet. We answer by e-mail.

No details at hand? A photo of the rating plate or the part is enough — simply attach it to the request.

Frequently asked

Questions that come up with this equipment.

Is HT/LT Cooling Water Pump data free?

Yes. Every model page, every guide and every datasheet for this type is readable without an account. An account adds saved searches and requests, nothing is taken away.

My model is missing — what now?

Send us the nameplate. We identify it by hand, add it to the library, and if you need a part or a service, the request is already on our desk.

Can you source a HT/LT Cooling Water Pump part?

Yes. Tell us the manufacturer, the model and what you need — a person reads every request and replies by e-mail.