Skip to content
OceanSphereENGINES
Library› Engine Room› Pumps› Steering Gear Hydraulic Pump
Pumps

Steering Gear Hydraulic Pump

The steering gear hydraulic pump is one of the handful of systems SOLAS requires to keep working even after a single failure — lose it without a backup running, and the ship loses the rudder.

SEIMI
Knowledge

What to check on a Steering Gear Hydraulic Pump.

10 models from SEIMI in Steering Gear Hydraulic Pump. Below: the full model list.

What sets the steering gear hydraulic pump apart

Most pumps in the engine room support a process that can be paused if the pump fails — cooling can be bridged, a transfer can wait. The steering gear pump cannot; a ship without rudder control in a seaway or a traffic separation scheme is in immediate danger. That is why steering gear is one of the few systems SOLAS treats as needing built-in redundancy at the pump level, not just at the system level: two independent power units, each capable of running the steering gear alone, so a single pump failure never leaves the ship without steering. The pump itself is usually a variable- or fixed-displacement hydraulic unit driving the rudder actuator directly, distinct from general service pumps in that its failure mode is tested and drilled specifically because of what happens if it is not caught immediately.

Steering gear hydraulic pump, block schematic
Block diagram of the duplicated steering gear hydraulic power units: two independent electric-motor-driven pumps drawing from a shared reservoir, each with its own relief valve, joined at a changeover valve that feeds the steering gear rams.

Legend

  1. electric motor 1
  2. pump 1 (running)
  3. relief valve (each pump)
  4. CHANGEOVER VALVE
  5. HYDRAULIC OIL RESERVOIR
  6. TO STEERING GEAR RAMS (rudder actuator)
  7. electric motor 2
  8. pump 2 (standby)
  9. both pumps are independent - either alone can move the rudder

Main components

Hydraulic pump unit

Typically a variable-displacement axial piston pump on larger ships, allowing rudder speed to be controlled by varying pump output rather than throttling flow, which is more efficient and gives smoother steering response.

Electric motor drive

Each pump has its own dedicated motor and its own power supply circuit, kept electrically independent from the other pump's circuit so a single electrical fault cannot take out both power units together.

Read the full guide

Relief and bypass valves

Protect the system against pressure spikes when the rudder meets sudden resistance, and allow the pump to be isolated for maintenance without depressurising the whole steering gear.

Changeover and control system

Lets the bridge or engine control room switch between the two power units, and on many installations, both pumps can be run together for faster rudder response in heavy weather or restricted waters.

Selection and sizing

  • Torque required to move the rudder at the specified rudder angle rate — SOLAS requires the ability to move the rudder from 35 degrees on one side to 30 degrees on the other within 28 seconds with the main steering gear.
  • Redundancy configuration: two independent pumps as a minimum, sized so either alone meets the required performance, not just the two combined.
  • Hydraulic fluid type and system pressure, matched to the actuator design and ambient temperature range the ship trades in.

Regulations and class

SOLAS Chapter II-1 sets the core requirements: main steering gear capable of the 35/30-degree rudder swing within the specified time, an auxiliary steering gear or equivalent redundancy, and independent power circuits for each unit so a single failure does not disable steering entirely. Class societies require steering gear, including the pump units, to be tested before departure on every voyage under SOLAS's pre-departure testing requirements, and periodic survey covers the changeover arrangement as well as the pumps themselves.

Typical faults

FaultConsequence
Internal pump wear, leaking past worn pistons or vanesSlow, spongy rudder response and reduced maximum rudder angle rate
Contaminated hydraulic fluidAccelerated wear across the whole system, valve sticking, unpredictable response
Relief valve set incorrectly or seizedEither nuisance tripping under normal load or no protection against a genuine overload
Both power circuits sharing an upstream electrical faultDefeats the entire redundancy design, both pumps lost together

What to look for in a supplier

  • Documented performance matching the SOLAS rudder angle and timing requirement for the specific rudder torque on this vessel.
  • Confirmed independence of the two power circuits at the design stage, not just at the pump nameplate.
  • Spare parts and seal kits held for the exact pump model, since steering gear downtime is not something a ship can plan around.

Run the full changeover sequence, not just a pump start, during the pre-departure steering gear test — a pump that starts fine can still fail to take over cleanly under load.

Models

Models in this type.

The best-documented model of each manufacturer first, then the next — 10 of 10 models in Steering Gear Hydraulic Pump. Every row links to full specifications, documents and service notes.

Showing only SEIMI. Show all manufacturers
By manufacturer

Manufacturers.

All 5 manufacturers with models of Steering Gear Hydraulic Pump. Names with a manufacturer page open it; the others open a search across the full library.

All manufacturers in the library
More than the data sheet shows

Write to us about your machine — the answer comes by e-mail.

Name the make and the model and what the job is: a spare, a service call, a second opinion on a data sheet. We answer by e-mail.

No details at hand? A photo of the rating plate or the part is enough — simply attach it to the request.

Frequently asked

Questions that come up with this equipment.

Is Steering Gear Hydraulic Pump data free?

Yes. Every model page, every guide and every datasheet for this type is readable without an account. An account adds saved searches and requests, nothing is taken away.

My model is missing — what now?

Send us the nameplate. We identify it by hand, add it to the library, and if you need a part or a service, the request is already on our desk.

Can you source a Steering Gear Hydraulic Pump part?

Yes. Tell us the manufacturer, the model and what you need — a person reads every request and replies by e-mail.