Skip to content
OceanSphereENGINES
Library› Engine Room› Pumps› Main Lube Oil Pump
Pumps

Main Lube Oil Pump

The main lube oil pump keeps oil moving to every bearing, gear, and cooler in the main engine, and unlike most auxiliary pumps it usually runs in a duty/standby pair because losing lube oil pressure for even a few seconds can wipe a bearing.

Rossi
Knowledge

What to check on a Main Lube Oil Pump.

4 models from Rossi in Main Lube Oil Pump. Below: the full model list.

What sets this pump apart from other engine-room pumps

Most pumps in an engine room can trip and give the crew a few minutes to react. A main lube oil pump cannot: a large two-stroke or medium-speed main engine loses usable bearing oil film within seconds of a pressure drop, so this pump is built and installed around continuity of supply rather than efficiency or flow economy. That is why it is almost always fitted as a duty and standby pair with automatic changeover, sometimes backed by a smaller engine-driven or gravity-fed emergency supply that covers the changeover gap itself.

Main lube oil pump cross-section
Cross-section of the main lube oil pump: motor drive through a flexible coupling into the pump casing where a meshing gear set draws oil in from the suction branch and delivers it under pressure through the discharge branch, with a pressure relief valve on the casing.

Legend

  1. discharge to coolers/filters
  2. pressure relief valve
  3. pump casing
  4. motor / engine drive
  5. flexible coupling
  6. meshing gears (rotor set)
  7. suction from sump

Main components

  • Pump element — usually a screw (positive displacement) type for the steady, low-pulsation flow lube oil circuits need, though centrifugal types appear on some medium-speed engines.
  • Drive — electric motor drive for the standby unit, and on many designs for the duty unit as well; some main engines take a shaft-driven duty pump direct off the crankshaft with an electric standby.
  • Pressure relief valve — protects the circuit against dead-heading if downstream filters or coolers clog.
  • Suction strainer — coarse protection ahead of the pump, separate from the fine filters further downstream.
  • Automatic changeover control — pressure switches that start the standby pump and alarm on a detected drop, sized to act faster than the oil film can collapse.

Selection and sizing

Capacity is set by the engine builder against the main engine's total lube oil circuit demand, including coolers, filters, and any turbocharger or reduction gear taking oil from the same system, plus a margin for fouled filters. Discharge pressure has to hold the required minimum at the farthest and highest bearing in the circuit, not just at the pump outlet. Motor rating for the standby pump needs enough starting torque to bring the system up to pressure quickly against cold, viscous oil, which is the condition it is most likely to start under.

Regulations and class

Class rules require a standby lube oil pump for the main engine with automatic start on low pressure, and periodic testing of the automatic changeover as part of the machinery survey regime. Alarm and slow-down or shutdown functions tied to lube oil pressure are checked at each class survey and are a standard item in the planned maintenance system's test schedule.

Read the full guide

Typical faults

FaultConsequence
Worn screw or gear clearancesFalling volumetric efficiency reduces delivered flow before pressure gauges show an obvious drop.
Suction strainer partially cloggedCavitation at the pump inlet, noise, and accelerated wear on the pump element.
Automatic changeover not tested regularlyStandby pump fails to start on demand, discovered only during an actual pressure loss.
Relief valve set incorrectly or seizedEither nuisance blow-off under normal load or no protection at all against a blocked circuit.

What to look for in a supplier

  • Performance curve matched to the actual engine builder's lube oil circuit data, not a generic pump selection.
  • Spares kit that covers wear parts specific to the screw or gear set, since these are rarely interchangeable between makers.
  • Confirmed compatibility with the existing automatic changeover and alarm wiring if this is a replacement rather than a newbuild fit.
  • Documented factory test showing rated flow and pressure, not just a design datasheet.

Test the automatic changeover under load, not with the engine stopped — a standby pump that starts fine on a static test can still fail to pick up the full flow fast enough once the main engine is actually turning.

Models

Models in this type.

The best-documented model of each manufacturer first, then the next — 4 of 4 models in Main Lube Oil Pump. Every row links to full specifications, documents and service notes.

Showing only Rossi. Show all manufacturers
By manufacturer

Manufacturers.

All 7 manufacturers with models of Main Lube Oil Pump. Names with a manufacturer page open it; the others open a search across the full library.

All manufacturers in the library
More than the data sheet shows

Write to us about this model — the answer comes by e-mail.

Name the make and the model and what the job is: a spare, a service call, a second opinion on a data sheet. We answer by e-mail.

No details at hand? A photo of the rating plate or the part is enough — simply attach it to the request.

Frequently asked

Questions that come up with this equipment.

Is Main Lube Oil Pump data free?

Yes. Every model page, every guide and every datasheet for this type is readable without an account. An account adds saved searches and requests, nothing is taken away.

My model is missing — what now?

Send us the nameplate. We identify it by hand, add it to the library, and if you need a part or a service, the request is already on our desk.

Can you source a Main Lube Oil Pump part?

Yes. Tell us the manufacturer, the model and what you need — a person reads every request and replies by e-mail.