Capstan
A capstan turns on a vertical axis and is built purely for warping lines under power; unlike a windlass it does not stow chain, so where deck space is tight it does the mooring job without a chain locker footprint.
What to check on a Capstan.
14 models from Quick in Capstan. Below: the full model list.
What sets a capstan apart
A capstan is a powered rotating drum on a vertical shaft, used to haul in mooring lines, warp the ship alongside a berth, or recover a line under tension that a crew could not handle by hand. The defining difference from a windlass is the axis: a windlass drum turns horizontally and is built around a chain wildcat to raise and lower the anchor, while a capstan has no wildcat and does not touch chain at all. Where deck arrangement allows a horizontal winch, yards usually fit a combined windlass; a standalone capstan appears where deck space around the winch is too narrow for a horizontal barrel, on poop decks, at midship mooring stations, or wherever a second independent pulling point is needed without running hydraulic or electric supply all the way from the forecastle.
Legend
- warping head
- rope turns on barrel
- local control station
- bolted deck flange
- deck
- gearbox and motor
Because the drum sits vertical, a line can be walked around it from almost any direction and tended by one or two crew standing at the barrel, paying out or taking in by hand while the machine supplies the pulling force. That geometry is why capstans remain common at mooring stations even on ships that also carry full windlass-winch combination units forward.
Main components
Drive unit
Electric motor or hydraulic motor mounted below deck, driving the barrel through a gear reducer. Hydraulic drive dominates on larger units because torque control at low, near-stall speed is easier to manage than with an electric motor alone.
Read the full guide
Warping drum / barrel
The vertical drum the line is walked around, usually with a slightly conical or waisted profile (whelped) so turns of rope do not ride up or jam. Barrel diameter and the number of turns taken determine how much load the friction of the rope against the drum can hold.
Brake
A band or disc brake on the drive shaft that holds a line under load without power to the motor, needed whenever the crew must let go the barrel to tend the line by hand.
Base and foundation
Capstans are through-bolted to a reinforced deck insert; the foundation, not the machine housing, carries the mooring load into the ship's structure, so foundation condition matters as much as the capstan itself.
Selection and sizing
Sizing turns on line pull, not drum diameter alone.
| Parameter | Typical range |
|---|---|
| Rated line pull | 30 - 150 kN depending on vessel size |
| Warping speed | 15 - 20 m/min at rated load |
| Rope diameter handled | usually matched to the ship's mooring line schedule, commonly 40 - 64 mm |
| Drive type | hydraulic for continuous duty stations, electric for lighter, occasional use |
Deck planners also check swept radius of the barrel against adjacent bulwarks, fairleads and bollards, and whether the motor and reducer fit below deck without fouling tanks or piping.
Regulations and class
Mooring equipment including capstans falls under the ship's approved mooring arrangement, reviewed by class against the equipment number calculated from the ship's dimensions, windage and displacement. Class rules require the safe working load to be marked at the machine and require periodic function testing and load-holding checks of the brake as part of the mooring equipment survey. There is no separate IMO convention specific to capstans; they are assessed as part of the anchoring and mooring system under the classification society's own rules.
Typical faults
- Brake slip under load - worn linings or contaminated brake surfaces let the drum creep, and a slipping brake under a loaded mooring line is a direct injury risk to anyone standing in the line's bight.
- Whelp and barrel wear - grooving from years of rope friction reduces grip, so the same number of turns holds less load than it used to.
- Gear reducer oil leakage - seal wear lets lubricant escape, and a reducer run low on oil overheats and can seize under sustained warping load.
- Hydraulic motor loss of torque - internal wear or a failing relief valve setting shows up as a capstan that stalls well below its rated pull.
What to look for in a supplier
- Documented rated line pull and warping speed backed by a test certificate, not just a nameplate figure.
- Brake design that holds rated load with the drive disengaged, verifiable at commissioning.
- Spares availability for the specific gear reducer and hydraulic motor model, since these are often proprietary to the winch maker.
- Deck foundation drawing compatible with the ship's existing bolting pattern where the unit replaces an older capstan.
Never stand in the bight of a line being taken in on a capstan - a slipping brake or a jammed turn on the barrel can put full mooring load through that loop in an instant.
Models in this type.
The best-documented model of each manufacturer first, then the next — 14 of 14 models in Capstan. Every row links to full specifications, documents and service notes.
Manufacturers.
All 40 manufacturers with models of Capstan. Names with a manufacturer page open it; the others open a search across the full library.
All manufacturers in the libraryShow all 40 manufacturers
Also in Anchor & Mooring Equipment.
The other equipment types in this category.
Write to us about this model — the answer comes by e-mail.
Name the make and the model and what the job is: a spare, a service call, a second opinion on a data sheet. We answer by e-mail.
No details at hand? A photo of the rating plate or the part is enough — simply attach it to the request.
Questions that come up with this equipment.
Is Capstan data free?
Yes. Every model page, every guide and every datasheet for this type is readable without an account. An account adds saved searches and requests, nothing is taken away.
My model is missing — what now?
Send us the nameplate. We identify it by hand, add it to the library, and if you need a part or a service, the request is already on our desk.
Can you source a Capstan part?
Yes. Tell us the manufacturer, the model and what you need — a person reads every request and replies by e-mail.