Outboard Engine (Petrol/SI)
A petrol outboard is a self-contained propulsion unit — engine, gearbox, and propeller in one clamp-on housing — chosen for small craft and tenders specifically because it can be removed, serviced, and swapped without any shaft line work on the boat itself.
What to check on an Outboard Engine (Petrol/SI).
252 models from Mercury Marine in Outboard Engine (Petrol/SI). Below: the full model list.
What makes this type
A spark-ignition (SI) outboard combines engine, cooling, gearbox, steering pivot, and propeller into a single unit that clamps or bolts to the transom, with no shaft line, no stern tube, and no separate rudder needed on small craft since the whole lower unit steers. This is what separates it from an inboard or sterndrive: the entire propulsion package tilts up out of the water for beach launching, storage, or to clear debris, and can be unbolted and replaced in a few hours. On a ship's tenders, rescue boats, and workboats, that swap-out simplicity is usually the deciding factor over an inboard diesel, alongside lighter weight for a given power output. Petrol/SI units differ from diesel outboards mainly in fuel handling and the ignition system — a spark plug and timed ignition rather than compression ignition — which brings petrol's flash point and vapour-handling hazards onto the boat.
Legend
- Powerhead (engine) under the cowling
- Transom clamp bracket
- Midsection (driveshaft housing)
- Tiller / steering arm
- Exhaust passage
- Driveshaft
- Cooling water intake
- Gearcase (lower unit)
- Cavitation plate
- Propeller
Main components
Powerhead
The engine itself, two-stroke or four-stroke, air- or (more commonly on modern units) water-cooled using raw seawater drawn through the lower unit.
Mid-section and exhaust
Routes exhaust down through the propeller hub on most designs, which quiets the exhaust note by discharging it underwater.
Read the full guide
Lower unit / gearcase
Contains the gear shift (forward-neutral-reverse) and the right-angle drive to the propeller shaft; gear oil in this housing is the first place water intrusion shows up, usually from a damaged propeller shaft seal after a strike on debris or the bottom.
Steering and tilt/trim
Manual or hydraulic steering pivots the whole lower unit; power trim adjusts the propeller thrust angle for load and speed, and manual tilt lifts the unit clear of the water when not in use.
Selection / Sizing
Power is matched to hull weight (including full complement and equipment for a rescue boat) and the required speed for its role — SOLAS rescue boats have minimum speed requirements that directly set the horsepower needed. Shaft length must match transom height; too short exposes the propeller and cavitation plate, too long drags the lower unit and adds resistance. For rescue boats and MOB (man overboard) boats, cold-start reliability and the ability to run inverted briefly or self-right without stalling the engine are practical selection factors beyond raw power.
Regulations / Class
Where the outboard powers a SOLAS rescue boat or fast rescue boat, LSA Code and SOLAS III performance requirements (minimum speed, ability to manoeuvre, engine starting in cold conditions) apply to the boat-and-engine combination as tested, not the engine alone. EPA 40 CFR 1045 (or the equivalent IMO/flag emissions standard) governs exhaust emissions for the engine as manufactured; class does not typically survey the outboard itself in detail but does survey the rescue boat and its readiness, including a functional engine start, at each inspection.
Typical faults
- Stale fuel / ethanol-blended petrol degradation — gum deposits in carburettors or injectors after long lay-up periods between drills, causing hard starting.
- Water-pump impeller wear — reduced raw-water cooling flow, leading to overheating that is often not noticed until the engine has already suffered damage.
- Propeller shaft seal damage from grounding or debris strike — allows water into the gearcase, contaminating the gear oil and corroding gears if not caught.
- Corroded electrical connections — salt air affects ignition and starting circuits faster on outboards than on enclosed inboard engines.
- Sacrificial anode depletion — accelerated galvanic corrosion of the lower unit once anodes are consumed and not replaced.
What to look for in a supplier
- Documented compliance testing for the specific rescue-boat combination, if the outboard is going onto a SOLAS boat, not just a generic power rating.
- Parts availability for the gearcase seals and water-pump impeller, the two highest-wear serviceable items.
- Cold-start reliability data if the vessel trades in cold climates, since a rescue boat engine that will not start defeats the boat's purpose.
- Corrosion protection package (anodes, coatings) suited to salt-water immersion and storage on davits exposed to spray.
Run rescue-boat outboards under load, not just a dockside start, at every drill — a warm start on the bench tells you nothing about whether the engine will push the boat clear of the ship's side.
Models in this type.
The best-documented model of each manufacturer first, then the next — 100 of 252 models in Outboard Engine (Petrol/SI). Every row links to full specifications, documents and service notes.
Manufacturers.
All 29 manufacturers with models of Outboard Engine (Petrol/SI). Names with a manufacturer page open it; the others open a search across the full library.
All manufacturersAlso in Shaft Line & Propulsion.
The other equipment types in this category.
One request. A person reads it and replies by e-mail.
Tell us the manufacturer, the model and what you need — a part, a service call, a second opinion. A person reads every request and replies by e-mail.
No details at hand? A photo of the rating plate or the part is enough — simply attach it to the request.
Three things people ask first.
Is Outboard Engine (Petrol/SI) data free?
Yes. Every model page, every guide and every datasheet for this type is readable without an account. An account adds saved searches and requests, nothing is taken away.
My model is missing — what now?
Send us the nameplate. We identify it by hand, add it to the library, and if you need a part or a service, the request is already on our desk.
Can you source a Outboard Engine (Petrol/SI) part?
Yes. Tell us the manufacturer, the model and what you need — a person reads every request and replies by e-mail.