Pipe & Valve Coating
Coating a valve is not the same job as coating a straight run of pipe: seat faces, stem threads and flange gaskets must stay coating-free, so pipe and valve coating is specified and applied differently even when the base paint system is identical.
What to check on a Pipe & Valve Coating.
1 models from Carboline in Pipe & Valve Coating. Below: the full model list.
What sets pipe and valve coating apart
Hull and tank coatings are applied to large flat or gently curved steel areas and judged mainly on dry film thickness and adhesion. Piping and valve coating has to deal with threads, flanges, seat faces, small internal bores and, in sea chests and overboard lines, near-permanent immersion combined with biofouling pressure. The coating has to survive being masked around moving or mating parts, and in way of valves it must not be applied anywhere it could interfere with sealing or operation, which makes masking discipline as important as the paint itself.
Main components of the system
Surface preparation
Abrasive blasting or power tool cleaning to the specified standard before coating; residual mill scale or old coating left under a new system is the single most common cause of early failure.
Primer
Zinc-rich epoxy or equivalent primer for corrosion protection, chosen for compatibility with the intended topcoat and with the pipe's service, whether that is seawater, fuel, ballast or a dry utility line.
Read the full guide
Intermediate and topcoat
Epoxy or polyurethane systems for external piping and exposed valve bodies; specialist foul-release or biocidal coatings for sea chests and overboard piping where marine growth restricts flow.
Masking of functional surfaces
Valve seats, stem threads, gasket faces and any machined mating surface are masked before coating and the masking is only removed after cure, since coating on a seat face causes a leak path that no amount of torque on the bolts will close.
Selection and sizing
- Service medium and temperature, since fuel and steam lines need a different resin system than seawater or bilge piping
- Immersion category, because permanently wetted sea chest and overboard piping needs antifouling performance that a dry cargo line does not
- Dry film thickness specified per coat and in total, checked with a calibrated gauge rather than assumed from the number of coats applied
- Compatibility with any cathodic protection already fitted in sea chests, since some coatings interact with sacrificial anodes
Regulations and class
There is no single dedicated SOLAS or MARPOL chapter for pipe and valve coating, but class rules require coatings in way of ballast and void spaces to meet recognised performance standards, and the IMO Performance Standard for Protective Coatings applies where ballast tank piping and supports are concerned. Antifouling coatings used on sea chests and overboard piping must comply with the AFS Convention's restrictions on biocidal active substances, which ruled out tributyltin systems and continues to restrict others.
Typical faults
| Fault | Cause | Consequence |
|---|---|---|
| Coating failure at welds and flanges | Inadequate surface preparation or insufficient film build at edges and corners | Localised corrosion starting exactly where inspection is hardest, under insulation or lagging |
| Valve seized or leaking | Coating applied over seat face or stem thread despite masking instructions | Valve fails to seal or fails to operate, sometimes not discovered until the next overhaul |
| Premature biofouling | Wrong coating class specified for a permanently immersed sea chest | Reduced flow, increased pumping power, blocked strainers |
| Blistering | Coating applied over residual moisture or contamination | Disbondment and accelerated corrosion under the blister |
What to look for in a supplier
- A written coating specification stating surface preparation standard, number of coats and dry film thickness per coat, not just a product name
- Confirmation that seat faces, threads and gaskets are masked as standard practice, with masking removal as a signed-off step
- Performance history or independent test data for antifouling coatings on sea chests, not only hull antifouling data applied by extension
- Batch traceability so a coating failure can be traced back to a specific application date and applicator
If a valve is hard to operate right after a coating job, do not force it — check for paint on the seat or stem before assuming it just needs breaking in.
Models in this type.
The best-documented model of each manufacturer first, then the next — 1 of 1 models in Pipe & Valve Coating. Every row links to full specifications, documents and service notes.
Manufacturers.
All 4 manufacturers with models of Pipe & Valve Coating. Names with a manufacturer page open it; the others open a search across the full library.
All manufacturersAlso in Paint & Coating Systems.
The other equipment types in this category.
One request. A person reads it and replies by e-mail.
Tell us the manufacturer, the model and what you need — a part, a service call, a second opinion. A person reads every request and replies by e-mail.
No details at hand? A photo of the rating plate or the part is enough — simply attach it to the request.
Three things people ask first.
Is Pipe & Valve Coating data free?
Yes. Every model page, every guide and every datasheet for this type is readable without an account. An account adds saved searches and requests, nothing is taken away.
My model is missing — what now?
Send us the nameplate. We identify it by hand, add it to the library, and if you need a part or a service, the request is already on our desk.
Can you source a Pipe & Valve Coating part?
Yes. Tell us the manufacturer, the model and what you need — a person reads every request and replies by e-mail.