Fire Retardant Coating
A fire retardant coating protects structural steel's load-bearing capacity in a fire, not the steel from corrosion; an intumescent system that has done its corrosion job perfectly can still fail its actual purpose if the fire-rated topcoat is damaged or overpainted incorrectly.
What to check on a Fire Retardant Coating.
10 models from International Paint in Fire Retardant Coating. Below: the full model list.
What sets fire retardant coating apart
Most coating systems on a ship exist to keep steel from rusting. A fire retardant, or intumescent, coating has a different job: keeping structural steel below the temperature at which it loses load-bearing strength for a defined period during a fire, buying time for evacuation and firefighting. Under heat, the intumescent layer swells into a thick, insulating char that slows heat transfer into the steel beneath it. This is passive fire protection, distinct from active systems like sprinklers, and it is rated in minutes of protection, not in years of service life the way anticorrosive coatings are.
Main components
Primer
An anticorrosive base coat compatible with the intumescent layer above it; incompatible primer-topcoat pairing is one of the most common causes of adhesion failure.
Intumescent layer
The reactive coating itself, typically epoxy or water-based, applied at a specific dry film thickness that is calculated, not estimated, for the required fire rating.
Read the full guide
Topcoat / seal coat
A protective finish over the intumescent layer to guard it against mechanical damage and weathering, since a scraped or eroded intumescent film cannot swell evenly when it is needed.
Selection criteria
- Required fire rating in minutes (commonly A-60, A-30 or H-class equivalents), which drives the dry film thickness specification directly.
- Substrate profile the coating is rated for -- beams, columns and hollow sections each have published thickness charts, and a coating tested on one profile is not automatically valid on another.
- Compatibility with the existing corrosion protection system if the intumescent is being applied to previously coated steel.
Regulations and class
SOLAS Chapter II-2 sets the fire integrity requirements for structural divisions and bulkheads that intumescent coatings are used to satisfy, and the coating system must carry fire test approval to the relevant standard for the specific steel profile and rating claimed. Class societies check that the applied dry film thickness matches the approved fire test certificate before accepting the installation, and any later overpainting must be verified against the same approval or it can void the fire rating.
Typical faults
- Overpainting with an incompatible topcoat during routine maintenance, which can insulate the intumescent layer and prevent it from reacting correctly in a fire.
- Dry film thickness below the certified minimum, invisible without a coating thickness gauge and common where application was rushed.
- Mechanical damage from fitting-out work after the fire coating was applied, leaving bare or thin patches on beams later hidden by ceiling panels.
- Cracking or loss of adhesion from substrate movement, more likely where surface preparation or primer selection was inadequate for the intumescent above it.
What to look for in a supplier
- Fire test certification covering the exact steel profile, thickness and orientation used on the vessel, not a generic rating.
- Compatibility guidance for maintenance overcoating so future repainting does not compromise the certified system.
- Application records including dry film thickness measurements at handover, since these are what class and flag state will ask for later.
Never let routine maintenance painting touch a certified fire coating without checking the approved system first -- a well-meaning coat of the wrong topcoat can quietly erase a fire rating that took a full test programme to establish.
Models in this type.
The best-documented model of each manufacturer first, then the next — 10 of 10 models in Fire Retardant Coating. Every row links to full specifications, documents and service notes.
Manufacturers.
All 24 manufacturers with models of Fire Retardant Coating. Names with a manufacturer page open it; the others open a search across the full library.
All manufacturersAlso in Paint & Coating Systems.
The other equipment types in this category.
One request. A person reads it and replies by e-mail.
Tell us the manufacturer, the model and what you need — a part, a service call, a second opinion. A person reads every request and replies by e-mail.
No details at hand? A photo of the rating plate or the part is enough — simply attach it to the request.
Three things people ask first.
Is Fire Retardant Coating data free?
Yes. Every model page, every guide and every datasheet for this type is readable without an account. An account adds saved searches and requests, nothing is taken away.
My model is missing — what now?
Send us the nameplate. We identify it by hand, add it to the library, and if you need a part or a service, the request is already on our desk.
Can you source a Fire Retardant Coating part?
Yes. Tell us the manufacturer, the model and what you need — a person reads every request and replies by e-mail.