Skip to content
OceanSphereENGINES
Library› Engine Room› Shaft Line & Propulsion› Sterndrive / Inboard Engine (Petrol/SI)
Shaft Line & Propulsion

Sterndrive / Inboard Engine (Petrol/SI)

A petrol sterndrive or inboard engine is a spark-ignition, marinized automotive-derived block certified under EPA 40 CFR 1045, used on recreational and light commercial craft where its power-to-weight and low first cost beat a diesel of the same output, at the cost of a strict ventilation and ignition-protection regime that diesel installations do not carry.

KEM Equipment
Knowledge

What to check on a Sterndrive / Inboard Engine (Petrol/SI).

95 models from KEM Equipment in Sterndrive / Inboard Engine (Petrol/SI). Below: the full model list.

What defines this type

This type covers spark-ignition (SI) petrol engines in two installation forms: sterndrive, where the engine sits forward of the transom and drives an outdrive leg through the hull, and straight inboard, where the engine drives a conventional shaft, often through a V-drive gearbox to keep the engine aft. Both share the same certified engine family; what differs is the drive train behind the flywheel. The defining risk that separates this type from any diesel propulsion engine is fuel vapour: petrol vapour is heavier than air, ignitable at far lower concentrations than diesel fumes, and a source of engine-space explosions if ventilation is neglected.

Sterndrive propulsion arrangement
Side view of an inboard petrol engine mounted forward of the transom, driving through the gimbal housing to a sterndrive outdrive with propeller, skeg and trim and tilt cylinder.

Legend

  1. Transom
  2. Engine block
  3. Trim / tilt cylinder
  4. Gimbal housing (drive shaft)
  5. Outdrive (upper gearcase)
  6. Engine mounts
  7. Lower unit (leg)
  8. Propeller
  9. Skeg

Main components

  • Marinized SI block – an automotive-derived engine adapted with marine cooling, exhaust and ignition-protected ancillaries, sold under an EPA-certified engine family.
  • Ignition system – coil-on-plug or distributor ignition; corrosion and moisture at plug boots and connectors are the leading cause of misfire in this environment.
  • Fuel system – electronic fuel injection on current models, fitted with a flame arrestor on the air intake where the engine sits in an enclosed space.
  • Raw water cooling – a rubber impeller pump drawing seawater through a heat exchanger, keeping the engine on a closed antifreeze circuit.
  • Wet exhaust – raw water injected into the exhaust manifold and riser to cool the exhaust gas before it exits, avoiding a dry high-temperature exhaust run through a fibreglass or wood hull.
  • Sterndrive leg or V-drive gearbox – the sterndrive unit carries its own gear ratio, trim range and bellows sealing the hull penetration; a V-drive routes shaft drive back through the boat to an aft-facing engine.

Selection and sizing

Selection is driven by installed horsepower against hull displacement and intended speed, then by the outdrive or gearbox ratio matched to the propeller. Relevant figures:

  • Rated horsepower and torque curve for the certified engine family, not a tuned or aftermarket figure.
  • Sterndrive gear ratio and trim range if steep hull deadrise or high-speed running is expected.
  • Cooling system capacity relative to expected raw water temperature at the operating area.
  • Propeller shaft diameter and material where the installation is a straight inboard rather than a sterndrive leg.

Regulations

The engine family itself is certified under EPA 40 CFR 1045 for spark-ignition marine engines. Around the installation, gasoline engine spaces are subject to mandatory power ventilation with a bilge blower run before starting, and electrical components in the engine space must be ignition-protected to avoid becoming an ignition source for accumulated vapour. Builders commonly reference recognised recreational marine industry standards for fuel systems, ventilation and ignition protection when specifying these installations.

Read the full guide

Typical faults

FaultConsequence
Ventilation blower not run before starting, or blower failureFuel vapour accumulation in the bilge with explosion risk on ignition
Raw water pump impeller wearOverheating that can warp the exhaust manifold and crack a cylinder head
Corroded ignition componentsMisfire and rough running, worse in humid or salt-spray conditions
Sterndrive bellows or seal failureWater ingress at the transom penetration, in the worst case sinking at the berth
Depleted outdrive anodesAccelerated galvanic corrosion of the drive leg and propeller shaft

What to look for in a supplier

  • Confirmed EPA-certified engine family and emissions label for the installation's flag or market.
  • Ignition-protected electrical fittings throughout the engine space, not just at the engine itself.
  • Outdrive gear ratio and trim range matched to the specific hull, not a generic recommendation.
  • Availability of the automotive-block parts platform locally, since this drives long-term serviceability more than any marine-specific part.
  • A documented anode replacement programme as part of the supply and commissioning package.

Never skip the pre-start blower run on a petrol installation, even for a quick trip to the fuel dock; it is the one habit that separates a routine start from a bilge explosion.

Models

Models in this type.

The best-documented model of each manufacturer first, then the next — 95 of 95 models in Sterndrive / Inboard Engine (Petrol/SI). Every row links to full specifications, documents and service notes.

Showing only KEM Equipment. Show all manufacturers
KEM EquipmentBKEMM02.4SIM 93 kW KEM EquipmentBKEMM04.3SIM 160 kW KEM EquipmentBKEMM06.0SIM 231 kW KEM EquipmentCKEMM02.4SIM 93 kW KEM EquipmentCKEMM04.3SIM 160 kW KEM EquipmentCKEMM06.0SIM 231 kW KEM EquipmentCKEMM06.2SIM 310 kW KEM EquipmentDKEMM02.4SIM 93 kW KEM EquipmentDKEMM04.3SIM 160 kW KEM EquipmentDKEMM06.0SIM 231 kW KEM EquipmentEKEMM02.4SIM 93 kW KEM EquipmentEKEMM06.0SIM 231 kW KEM EquipmentEKEMM06.2SIM 310 kW KEM EquipmentFKEMM02.4SIM 93 kW KEM EquipmentFKEMM04.3DIM 235 kW KEM EquipmentFKEMM04.3SIM 160 kW KEM EquipmentFKEMM06.0SIM 231 kW KEM EquipmentFKEMM06.2LSA 379 kW KEM EquipmentFKEMM06.2SIM 310 kW KEM EquipmentGKEMM02.4SIM 93 kW KEM EquipmentGKEMM04.3SIM 160 kW KEM EquipmentGKEMM06.2DIM 302 kW KEM EquipmentGKEMM06.2LSA 379 kW KEM EquipmentHKEMM02.4SIM 93 kW KEM EquipmentHKEMM04.3DIM 235 kW KEM EquipmentHKEMM04.3SIM 160 kW KEM EquipmentHKEMM05.3DIM 251 kW KEM EquipmentHKEMM06.0SIM 231 kW KEM EquipmentHKEMM06.2DIM 302 kW KEM EquipmentHKEMM06.2LSA 379 kW KEM EquipmentJKEMM02.4SIM 93 kW KEM EquipmentJKEMM04.3DIM 235 kW KEM EquipmentJKEMM04.3SIM 160 kW KEM EquipmentJKEMM05.3DIM 251 kW KEM EquipmentJKEMM06.0SIM 231 kW KEM EquipmentJKEMM06.2DIM 302 kW KEM EquipmentJKEMM06.2LSA 379 kW KEM EquipmentKKEMM02.4SIM 93 kW KEM EquipmentKKEMM04.3DIM 235 kW KEM EquipmentKKEMM04.3SIM 160 kW KEM EquipmentKKEMM06.2LSA 379 kW KEM EquipmentLKEMM02.4SIM 93 kW KEM EquipmentLKEMM04.3DIM 235 kW KEM EquipmentLKEMM04.3SIM 160 kW KEM EquipmentLKEMM05.3DIM 251 kW KEM EquipmentLKEMM06.0SIM 231 kW KEM EquipmentLKEMM06.2DIM 302 kW KEM EquipmentLKEMM06.2LSA 379 kW KEM EquipmentLKEMM06.2LT4 444 kW KEM EquipmentLKEMM07.4LSX 381 kW KEM EquipmentMKEMM04.3DIM 235 kW KEM EquipmentMKEMM04.3SIM 160 kW KEM EquipmentMKEMM05.3DIM 251 kW KEM EquipmentMKEMM06.0SIM 231 kW KEM EquipmentMKEMM06.2DIM 302 kW KEM EquipmentMKEMM06.2LT4 444 kW KEM EquipmentMKEMM07.4LSX 381 kW KEM EquipmentNKEMM05.3DIM 251 kW KEM EquipmentNKEMM06.2DIM 302 kW KEM EquipmentNKEMM06.2LT4 444 kW KEM EquipmentNKEMM07.4LSX 381 kW KEM EquipmentPKEMM05.3DIM 251 kW KEM EquipmentPKEMM06.0SIM 231 kW KEM EquipmentPKEMM06.2LT4 444 kW KEM EquipmentPKEMM07.4LSX 381 kW KEM EquipmentRKEMM04.3DIM 235 kW KEM EquipmentRKEMM05.3DIM 251 kW KEM EquipmentRKEMM06.0SIM 231 kW KEM EquipmentRKEMM06.2LT4 444 kW KEM EquipmentRKEMM07.4LSX 381 kW KEM EquipmentSKEMM04.3DIM 235 kW KEM EquipmentSKEMM06.0SIM 231 kW KEM EquipmentSKEMM06.2DIM 302 kW KEM EquipmentSKEMM06.2LT4 444 kW KEM EquipmentSKEMM07.4LSX 381 kW KEM EquipmentTKEMM04.3DIM 235 kW KEM EquipmentTKEMM05.3DIM 251 kW KEM EquipmentTKEMM06.2DIM 302 kW KEM EquipmentTKEMM06.2LT4 444 kW KEM EquipmentTKEMM07.4LSX 381 kW KEM EquipmentDKEMM06.2SIM 310 kW KEM EquipmentEKEMM04.3SIM 160 kW KEM EquipmentGKEMM04.3DIM 235 kW KEM EquipmentGKEMM05.3DIM 251 kW KEM EquipmentGKEMM06.0SIM 231 kW KEM EquipmentKKEMM05.3DIM 251 kW KEM EquipmentKKEMM06.0SIM 231 kW KEM EquipmentKKEMM06.2DIM 302 kW KEM EquipmentNKEMM04.3DIM 235 kW KEM EquipmentNKEMM06.0SIM 231 kW KEM EquipmentPKEMM04.3DIM 235 kW KEM EquipmentPKEMM06.2DIM 302 kW KEM EquipmentRKEMM06.2DIM 302 kW KEM EquipmentSKEMM05.3DIM 251 kW KEM EquipmentTKEMM06.0SIM 231 kW
95 models
More than the data sheet shows

Write to us about this model — the answer comes by e-mail.

Name the make and the model and what the job is: a spare, a service call, a second opinion on a data sheet. We answer by e-mail.

No details at hand? A photo of the rating plate or the part is enough — simply attach it to the request.

Frequently asked

Questions that come up with this equipment.

Is Sterndrive / Inboard Engine (Petrol/SI) data free?

Yes. Every model page, every guide and every datasheet for this type is readable without an account. An account adds saved searches and requests, nothing is taken away.

My model is missing — what now?

Send us the nameplate. We identify it by hand, add it to the library, and if you need a part or a service, the request is already on our desk.

Can you source a Sterndrive / Inboard Engine (Petrol/SI) part?

Yes. Tell us the manufacturer, the model and what you need — a person reads every request and replies by e-mail.