Skip to content
OceanSphereENGINES
Library› Safety & LSA› Fixed Fire Suppression› Fixed Gas Extinguishing System
Fixed Fire Suppression

Fixed Gas Extinguishing System

A fixed gas system floods an entire enclosed space with an inert or chemical agent to strip a fire of oxygen, which means it can only be released once the space is confirmed empty and sealed — a step that has cost crew lives on ships when skipped or rushed.

Minimax Marine
Knowledge

What to check on a Fixed Gas Extinguishing System.

2 models from Minimax Marine in Fixed Gas Extinguishing System. Below: the full model list.

What defines this type

A fixed gas extinguishing system protects a whole enclosed space rather than a point source, releasing an agent, most commonly CO2 but also increasingly inert gas blends, that displaces or dilutes oxygen below the level needed for combustion. That mechanism is exactly why it differs so sharply from water-based fixed systems: the space has to be evacuated and sealed before release, because the same agent that suffocates a fire suffocates a person, and CO2 in particular has caused fatalities on ships when crew entered a space during or shortly after discharge.

Fixed gas extinguishing system
Flow of a fixed gas fire suppression system from the cylinder storage room through a manifold and release valve into distribution piping that carries the agent to nozzles inside a sealed protected space, with the pre-discharge alarm shown outside the entrance.

Legend

  1. cylinder room
  2. protected space (engine room)
  3. distribution piping
  4. discharge nozzles
  5. cylinder bank
  6. release valve
  7. audible alarm before release
  8. door

Main components

Agent storage

A bank of high-pressure cylinders, typically for CO2, or a bulk low-pressure storage tank on larger installations, sized to deliver the design concentration to the largest single protected space.

Release mechanism

A manually operated pull-cable or pneumatic release station outside the protected space, deliberately requiring a human decision rather than being fully automatic on most cargo ship engine room installations, paired with an alarm that sounds inside the space before discharge.

Read the full guide

Distribution piping

Fixed pipework from the cylinder bank to discharge nozzles positioned to flood the space evenly, sized so the design concentration is reached within the time class rules require.

Space sealing arrangements

Dampers or shutters that close ventilation openings automatically or manually before release, since the system cannot hold its concentration in a space that is still being ventilated.

Selection and sizing

The extinguishing concentration and quantity of agent are calculated from the protected space's gross volume, with allowances for permanent openings that cannot be closed. CO2 systems are sized to deliver a specified percentage of the space volume within a set number of minutes; inert gas and other clean agent systems use different design concentrations depending on the agent's extinguishing mechanism. The choice between CO2 and an alternative agent often comes down to space size and occupancy pattern, since some alternative agents are approved for use in normally occupied spaces at lower risk than CO2, at higher cost and storage volume for the same protection.

Regulations and class

SOLAS Chapter II-2 and the Fire Safety Systems Code set the required extinguishing concentration, discharge time and alarm sequencing for fixed gas systems by space type. A pre-discharge alarm audible throughout the protected space, with enough delay to allow evacuation before release, is mandatory. Class surveys include a weighing or pressure check of a sample of cylinders to confirm agent quantity has not leaked away, since a cylinder can appear intact while having lost enough gas to fail the design concentration.

Typical faults

FaultCauseConsequence
Low cylinder weight or pressureSlow leakage past the cylinder valve seal over years of serviceInsufficient agent quantity to reach the design concentration if the system is released
Release cable stiff or bindingCorrosion or incorrect routing of the pull-cable through its guidesDelayed or failed manual release in an emergency
Ventilation dampers not closing fullyMechanical wear or seized linkage on rarely operated dampersAgent concentration cannot build up to the extinguishing level, or dilutes out through the opening
Pre-discharge alarm inaudible in part of the spaceAlarm sounder count or placement not matching the space's actual noise levels and layoutCrew in the space may not receive adequate warning before discharge

What to look for in a supplier

  • Type-approved system design matching the actual protected volume, including documented allowance for openings that cannot be sealed
  • Cylinder testing and refill service that returns a weight or pressure certificate, not just a visual inspection
  • Compatibility of new components with the existing pipework and nozzle layout if only part of the system is being renewed
  • Clear documentation of the release sequence and delay timing for crew training, not only for the installation itself

Never treat a CO2 space entry as routine — confirm the release lockout is engaged and the space has been ventilated and gas-tested, every time, regardless of how long ago the system was last discharged.

Models

Models in this type.

The best-documented model of each manufacturer first, then the next — 2 of 2 models in Fixed Gas Extinguishing System. Every row links to full specifications, documents and service notes.

Showing only Minimax Marine. Show all manufacturers
2 models
By manufacturer

Manufacturers.

All 12 manufacturers with models of Fixed Gas Extinguishing System. Names with a manufacturer page open it; the others open a search across the full library.

All manufacturers in the library

Inspection findings for this equipment

From public port state control and US Coast Guard records; OceanSphere assigns them to this equipment type from the descriptions.

Deficiency codes – USCG port state control – foreign-flag vessels

USCG components

All inspection & safety data ›

More than the data sheet shows

Write to us about this model — the answer comes by e-mail.

Name the make and the model and what the job is: a spare, a service call, a second opinion on a data sheet. We answer by e-mail.

No details at hand? A photo of the rating plate or the part is enough — simply attach it to the request.

Frequently asked

Questions that come up with this equipment.

Is Fixed Gas Extinguishing System data free?

Yes. Every model page, every guide and every datasheet for this type is readable without an account. An account adds saved searches and requests, nothing is taken away.

My model is missing — what now?

Send us the nameplate. We identify it by hand, add it to the library, and if you need a part or a service, the request is already on our desk.

Can you source a Fixed Gas Extinguishing System part?

Yes. Tell us the manufacturer, the model and what you need — a person reads every request and replies by e-mail.