Fuel Oil Separator
A fuel oil separator spins raw bunkered fuel at several thousand rpm to throw water and abrasive catalyst fines out before the oil reaches an injector, and a unit running with the wrong gravity disc for that fuel's density will pass the contamination through instead of removing it.
What to check on a Fuel Oil Separator.
6 models from Wärtsilä in Fuel Oil Separator. Below: the full model list.
What defines this type
A fuel oil separator uses centrifugal force in a spinning bowl to exploit the density difference between oil, water and solid contaminants such as catalyst fines and sludge. Run as a purifier, it removes both water and solids and needs a gravity disc or automatic water-detection interface matched to the fuel's density; run as a clarifier, with no water outlet in use, it handles solids removal alone on fuel with very low water content. Compared with a lube oil separator, a fuel oil separator built for heavy fuel oil duty adds a pre-heater to bring viscosity down into the separable range and is built for higher continuous throughput, and modern units self-clean the bowl automatically at intervals instead of needing manual stripping down.
Legend
- Drive spindle
- Feed inlet
- Clean oil outlet
- Water outlet
- Gravity disc
- Disc stack
- Distributor
- Sludge space
- Rotating bowl
- Sludge outlet
Main components
- Bowl and disc stack — the rotating assembly where separation actually happens.
- Self-cleaning mechanism — a hydraulic sliding piston that ejects accumulated solids from the bowl at set intervals without stopping the unit.
- Gravity disc or automatic interface control — sets the separation boundary for the fuel's actual density, manually on older units or automatically on modern ones.
- Feed pump and pre-heater — deliver fuel at the flow and temperature the bowl needs, the pre-heater being essential for heavy fuel oil viscosity.
- Drive motor, gearbox and control panel — bring the bowl to operating speed and manage the automatic cycle.
Selection / sizing
Throughput is set from daily fuel consumption with a margin for cleaning cycles and downtime, expressed in litres per hour at the bowl. The gravity disc or automatic interface must cover the density range of the fuels actually carried — heavy fuel oil running close to 991 kg/m3 needs a very different setting from a light marine gas oil — and vessels now bunkering a mix of conventional and low-sulphur fuels need a unit whose interface handles that whole range without a disc change between fuels. Pre-heater temperature must be matched to the viscosity of the heaviest fuel carried, since under-heating is one of the most common causes of poor separation.
Regulations / Class
Class rules require duplicate fuel oil separators so treatment continues while one unit is out of service for overhaul. Sludge generated during separation must be logged in the Oil Record Book and discharged only to a shore reception facility or disposed of by an approved incinerator, under MARPOL Annex I and Annex VI. The oily water separator used for bilge water is a related but entirely separate piece of equipment, not to be confused with the fuel oil purifier.
Read the full guide
Typical faults
| Fault | Cause | Consequence |
|---|---|---|
| Bowl imbalance | Uneven sludge buildup between cleaning cycles | Vibration, bearing wear, automatic safety trip |
| Wrong gravity disc for fuel density | Disc not changed after a bunker of different density | Oil lost to the water outlet, or water carried through to the service tank |
| Pre-heater under-temperature | Heater fouling or control fault | Poor separation, catalyst fines reaching the injectors |
| Worn discs | Normal wear over service life | Reduced separation efficiency, more water and sediment in clean fuel |
What to look for in a supplier
- Throughput and density range matched to the vessel's actual and future fuel mix, including low-sulphur and biofuel blends.
- Spare disc stack and seal kits genuinely available, not just listed.
- Control system compatible with the vessel's existing alarm monitoring.
- A documented separation efficiency figure at the temperature the vessel actually operates at, not an idealised test condition.
Recheck the gravity disc or interface setting whenever the bunkered fuel's density changes meaningfully — a separator left set for the previous grade will quietly pass contamination through rather than flag anything wrong.
Models in this type.
The best-documented model of each manufacturer first, then the next — 6 of 6 models in Fuel Oil Separator. Every row links to full specifications, documents and service notes.
Manufacturers.
All 30 manufacturers with models of Fuel Oil Separator. Names with a manufacturer page open it; the others open a search across the full library.
All manufacturersAlso in Separators & Purifiers.
The other equipment types in this category.
One request. A person reads it and replies by e-mail.
Tell us the manufacturer, the model and what you need — a part, a service call, a second opinion. A person reads every request and replies by e-mail.
No details at hand? A photo of the rating plate or the part is enough — simply attach it to the request.
Three things people ask first.
Is Fuel Oil Separator data free?
Yes. Every model page, every guide and every datasheet for this type is readable without an account. An account adds saved searches and requests, nothing is taken away.
My model is missing — what now?
Send us the nameplate. We identify it by hand, add it to the library, and if you need a part or a service, the request is already on our desk.
Can you source a Fuel Oil Separator part?
Yes. Tell us the manufacturer, the model and what you need — a person reads every request and replies by e-mail.