UV-Based BWMS
UV treatment inactivates organisms in ballast water by damaging their DNA under ultraviolet light rather than killing them outright, which is why UV systems live and die by water clarity rather than by chemical dose.
What to check on a UV-Based BWMS.
110 models from BIO-UV in UV-Based BWMS. Below: the full model list.
What sets UV treatment apart
A UV-based ballast water management system passes ballast water through a reactor chamber lined with UV lamps that damage the DNA of organisms so they cannot reproduce, rather than killing them outright the way a biocide or electrochlorination system does. Because UV works by line-of-sight exposure through the water column, its performance depends directly on how much light actually reaches the organism — turbidity, suspended solids and biofouling on the lamp sleeves all cut effective dose, which is the main reason UV systems are paired with a filtration stage rather than sold as UV alone.
Legend
- monitoring and control
- filter
- UV reactor chamber
- UV lamps in quartz sleeves
- to ballast tanks
- ballast water inlet
- UV intensity sensor
Main components
Filter
A self-cleaning screen or disc filter, typically 20 to 50 micron, that strips out sediment, plankton and debris before the UV reactor so the remaining organisms are exposed to full-strength light.
UV reactor
A chamber holding banks of medium or low-pressure UV lamps in quartz sleeves, sized so every litre passing through receives the minimum dose the system was type-approved for at the vessel's rated flow.
Read the full guide
UV intensity sensors
Sensors that monitor light transmission through the water in real time and signal the control system to reduce flow or raise an alarm if dose falls below the approved threshold.
Control and monitoring unit
Logs treatment records for port state control and IMO compliance, and interlocks the ballast pumps so water cannot bypass the reactor.
Selection / Sizing
- Ballast pump flow rate, since the reactor must treat the full rated flow within its type-approved UV dose — undersizing the reactor for the pump forces a flow restriction that slows ballasting operations.
- Typical water turbidity for the vessel's trading pattern; a ship regularly ballasting in silty coastal or river water needs a more robust filter stage than one loading in open ocean.
- Lamp type and expected lamp life, since medium-pressure lamps run hotter and shorter but treat higher flows in a smaller footprint than low-pressure lamps.
- Space and power available, as UV systems draw meaningful electrical load and need a straight reactor run without tight bends.
Regulations / Class
Every seagoing ship has been required to carry an operational ballast water management system under the IMO BWM Convention since the 2024 compliance deadline, and the treatment system itself must hold IMO type approval (or USCG approval for US waters) confirming it meets the D-2 discharge standard for organism concentration. Class surveys check that treatment records are logged for every ballasting operation and that the system's approval certificate matches the installed configuration, including any approved operating envelope for turbidity or salinity.
Typical faults
| Fault | Cause | Consequence |
|---|---|---|
| Dose alarm during ballasting | High turbidity exceeding the system's approved operating range | Ballast operation slows or stops until water clarity improves |
| Reduced UV transmission | Biofouling or scaling on the quartz lamp sleeves | Effective dose drops even though lamps show as functioning |
| Filter backwash failure | Screen clogged faster than the automatic flush cycle clears it | Flow restriction forces reduced ballast pump throughput |
| Lamp failure undetected | Lamp ballast fault not cross-checked against intensity sensor reading | Water passes with an under-treated dose without an alarm |
What to look for in a supplier
- IMO type approval covering the actual flow rate and turbidity range the vessel will operate in, not just the headline capacity.
- Spare lamp and quartz sleeve availability at ports the vessel actually calls, since UV lamps are a wear item with a finite rated life.
- A service network able to recalibrate UV intensity sensors, which drift over time and are easy to overlook during routine maintenance.
A UV system logging a compliant dose in clear open-ocean water can still fail the same voyage in a silty river estuary — check the type-approval turbidity envelope against the vessel's actual ports before assuming coverage.
Models in this type.
The best-documented model of each manufacturer first, then the next — 100 of 110 models in UV-Based BWMS. Every row links to full specifications, documents and service notes.
Manufacturers.
All 26 manufacturers with models of UV-Based BWMS. Names with a manufacturer page open it; the others open a search across the full library.
All manufacturersAlso in Ballast Water Treatment Systems.
The other equipment types in this category.
One request. A person reads it and replies by e-mail.
Tell us the manufacturer, the model and what you need — a part, a service call, a second opinion. A person reads every request and replies by e-mail.
No details at hand? A photo of the rating plate or the part is enough — simply attach it to the request.
Three things people ask first.
Is UV-Based BWMS data free?
Yes. Every model page, every guide and every datasheet for this type is readable without an account. An account adds saved searches and requests, nothing is taken away.
My model is missing — what now?
Send us the nameplate. We identify it by hand, add it to the library, and if you need a part or a service, the request is already on our desk.
Can you source a UV-Based BWMS part?
Yes. Tell us the manufacturer, the model and what you need — a person reads every request and replies by e-mail.