Piggyback Hatch Cover
A piggyback hatch cover stacks two panels at one end of the hatch instead of folding or rolling them clear, trading some hold length for a mechanism with far fewer moving parts to jam or flood.
What to check on a Piggyback Hatch Cover.
36 models from MacGregor in Piggyback Hatch Cover. Below: the full model list.
What sets a piggyback cover apart from folding and rolling types
Folding hatch covers hinge their panels up and over each other; rolling covers run panels sideways on wheels along the coaming. A piggyback cover instead lifts one panel and stacks it directly on top of the neighbouring panel at one end of the hatch, using hydraulic cylinders rather than a chain or wire haul system. Because the panels simply lift and stack rather than folding through a hinge or travelling on a wheel track, there are fewer wear points exposed to green water and cargo dust, which is why the type is common on bulk carriers carrying abrasive cargoes.
Legend
- hydraulic lifting cylinder
- upper panel (lifted clear)
- wheels ride coaming rail
- lower panel (rests on rail)
- clear opening (hold access)
- coaming top rail
- coaming (hold end)
Main components
- Panels - steel pontoon-type sections, one designed to sit beneath and one to stack above at the parked end of the hatch.
- Hydraulic lifting cylinders - raise and lower each panel; power comes from a dedicated hydraulic power pack rather than a shared deck machinery system on most installations.
- Guide rollers and side guides - keep the panel aligned as it lifts clear of the coaming and travels to the stacking position.
- Cleating and compression system - hydraulic or manual cleats that pull the closed panel down onto the coaming compression bar to make the weathertight seal.
- Rubber sealing gasket - continuous gasket around the panel and coaming compression bar that does the actual watertight sealing work.
Selection and sizing
Panel count and stacking arrangement are set by hatch length and the headroom available above the coaming for the stacked panel - a piggyback system needs enough clear height that the stacked panel does not foul deck cranes, hatch coamings, or cargo gear stowed nearby. Hydraulic cylinder capacity is sized to the panel's loaded weight including any accumulated cargo residue, with margin, since cylinders that are only just adequate when new lose margin as seals wear.
Regulations and class
The International Load Line Convention and class rules for hatch cover strength set the required weathertight standard and the load the panel must withstand from green water and stowed cargo above it, where applicable. Class surveys include a hose test or ultrasonic test of the sealing line at each hatch cover and periodic examination of the securing and compression system; IACS unified requirements cover hatch cover design loads for bulk carriers specifically.
Read the full guide
Typical faults
- Gasket compression set - the rubber seal loses its spring after years of compression and no longer closes the gap when cleated, letting water track along the coaming.
- Guide roller wear allowing panel misalignment - a worn roller lets the panel drift sideways during lifting, catching the coaming and jamming mid-cycle.
- Hydraulic cylinder seal leakage - slow loss of lift capacity shows up as a panel that hesitates or drifts down under its own weight when parked.
- Corrosion at the coaming compression bar - pitting on the bar the gasket seats against prevents a full seal even with a healthy gasket.
What to look for in a supplier
- Gasket material rated for the trade's temperature range and cargo chemical exposure, not a generic rubber compound.
- Documented cylinder capacity margin above the calculated panel weight.
- Spare parts availability for guide rollers and cleating hardware specifically, the components that wear fastest.
- Reference installations on a comparable hatch size and cargo profile.
A hose test that passes on a piggyback cover does not confirm the cleating force is even across the whole panel - check compression at both ends and the middle, since a gasket can seal at the cleats and still leak at the panel's centre.
Models in this type.
The best-documented model of each manufacturer first, then the next — 36 of 36 models in Piggyback Hatch Cover. Every row links to full specifications, documents and service notes.
Manufacturers.
All 1 manufacturers with models of Piggyback Hatch Cover. Names with a manufacturer page open it; the others open a search across the full library.
All manufacturers in the libraryAlso in Hatch Covers & Cargo Access.
The other equipment types in this category.
Write to us about your machine — the answer comes by e-mail.
Name the make and the model and what the job is: a spare, a service call, a second opinion on a data sheet. We answer by e-mail.
No details at hand? A photo of the rating plate or the part is enough — simply attach it to the request.
Questions that come up with this equipment.
Is Piggyback Hatch Cover data free?
Yes. Every model page, every guide and every datasheet for this type is readable without an account. An account adds saved searches and requests, nothing is taken away.
My model is missing — what now?
Send us the nameplate. We identify it by hand, add it to the library, and if you need a part or a service, the request is already on our desk.
Can you source a Piggyback Hatch Cover part?
Yes. Tell us the manufacturer, the model and what you need — a person reads every request and replies by e-mail.