Skip to content
OceanSphereENGINES
Library› Deck› RoRo Equipment› Side Ramp
RoRo Equipment

Side Ramp

A side ramp lets a ferry load and discharge vehicles through an opening in the shell plating rather than over the stern, which matters at berths where stern access is blocked by other traffic or where the ship needs to work cargo from both a stern ramp and a side door at once to cut port time.

Damen Marine Components
Knowledge

What to check on a Side Ramp.

5 models from Damen Marine Components in Side Ramp. Below: the full model list.

What sets a side ramp apart

A side ramp is hinged into an opening in the shell plating, usually amidships or towards the bow, and swings or slides out to reach the quay independently of the stern ramp. It lets a ferry run simultaneous loading at two points, or serve berths where the stern is occupied by mooring gear, other vessels or a quay layout that does not line up with a stern ramp. Because it penetrates the hull below or near the waterline on many designs, its watertight integrity in the closed position is treated as seriously as any shell door.

Side ramp arrangement
Side view of a ferry side ramp lowered from a shell door opening to the quay, showing the hinge, the hydraulic operating ram and the vehicle deck it serves.

Legend

  1. shell door opening
  2. hydraulic ram
  3. vehicle deck
  4. hinge
  5. ramp
  6. quay

Main components

Ramp platform

A steel deck plate, often with a folding outer flap to extend reach onto the quay, rated for the axle loads of the vehicle traffic it is designed to take.

Hinges and pivot structure

Heavy pivot bearings built into reinforced hull framing, since the ramp must transmit both its own dead weight and moving vehicle loads back into the ship's structure.

Read the full guide

Hydraulic operating cylinders

Raise, lower and in side-loading designs also slew the ramp, with a separate locking system that holds the closed position independently of hydraulic pressure.

Watertight closing arrangement

Cleats, rubber gaskets and indicator lights confirming the ramp is fully closed and locked before the ship can sail, wired into the bridge indicator panel.

Selection and sizing

ParameterRelevance
Vehicle load ratingDetermines whether cars only or also trucks and trailers can use the ramp
Freeboard at the openingSets how far below the waterline the opening sits and therefore the closure and alarm requirements
Ramp angle rangeMust match the tidal range and quay height variation of the routes served
Slewing capabilitySide-loading versus straight side ramps changes berthing flexibility at irregular quays

Regulations and class

Side ramps and shell doors below the freeboard deck fall under SOLAS Chapter II-1 requirements for watertight doors and openings, developed after several high-profile RoRo losses linked to bow and stern door failures; indicator systems showing the closed and locked state must be provided on the bridge. Class rules set structural scantlings for the ramp and hinge structure based on vehicle loading, and periodic surveys include operational testing of the closing and locking arrangement, not just a visual check.

Typical faults

  • Hinge pin wear - years of vehicle loading work the pins loose, letting the ramp rack slightly and strain the locking cleats out of alignment.
  • Gasket degradation - UV and salt exposure harden the rubber seal, and a ramp that closes fine visually can still leak under sea state.
  • Indicator light faults - a false closed indication is more dangerous than an obvious fault, since the bridge team has no reason to check further.
  • Hydraulic cylinder drift - slow seal wear lets the ramp sag over a port stay, loading the locking cleats instead of the hydraulics as designed.

What to look for in a supplier

  • Structural certification tied to the actual vehicle load rating required, not a generic ramp design
  • Independent mechanical locking that holds position without relying on hydraulic pressure
  • Indicator system compatible with the bridge's existing hull opening monitoring panel
  • Spare gasket and seal kits sized for the specific ramp, since these wear faster than the steelwork

Test the closed-and-locked indicator against a physical check on a set schedule, not just at survey - an indicator fault that shows closed when the ramp is not fully cleated has been a direct cause of RoRo flooding casualties.

Models

Models in this type.

The best-documented model of each manufacturer first, then the next — 5 of 5 models in Side Ramp. Every row links to full specifications, documents and service notes.

Showing only Damen Marine Components. Show all manufacturers
5 models
By manufacturer

Manufacturers.

All 4 manufacturers with models of Side Ramp. Names with a manufacturer page open it; the others open a search across the full library.

All manufacturers in the library
Related types

Also in RoRo Equipment.

The other equipment types in this category.

Hoistable Car DeckInternal RampQuarter RampRoRo DoorStern Ramp
More than the data sheet shows

Write to us about this model — the answer comes by e-mail.

Name the make and the model and what the job is: a spare, a service call, a second opinion on a data sheet. We answer by e-mail.

No details at hand? A photo of the rating plate or the part is enough — simply attach it to the request.

Frequently asked

Questions that come up with this equipment.

Is Side Ramp data free?

Yes. Every model page, every guide and every datasheet for this type is readable without an account. An account adds saved searches and requests, nothing is taken away.

My model is missing — what now?

Send us the nameplate. We identify it by hand, add it to the library, and if you need a part or a service, the request is already on our desk.

Can you source a Side Ramp part?

Yes. Tell us the manufacturer, the model and what you need — a person reads every request and replies by e-mail.