Manifold Valve
The manifold valve, not the flange itself, is the ship's last point of positive shutoff for a cargo transfer, closed manually or by actuator within seconds of an emergency shutdown signal from the cargo control room.
What to check on a Manifold Valve.
1 models from Wärtsilä in Manifold Valve. Below: the full model list.
What a Manifold Valve Does That the Manifold Alone Cannot
The manifold valve is the last point of positive shutoff on the ship's side of the cargo transfer connection, distinct from the manifold flange itself, which is just the fixed connection point. Where the manifold provides the physical joint for the hose or loading arm, the valve is what lets the ship or terminal stop flow instantly, in an emergency or at the end of a planned transfer, without relying on a pump being switched off somewhere else in the system.
Main Components
Valve body and disc
Most manifold valves are butterfly or ball type for quick quarter-turn operation, sized to the manifold bore, commonly 150mm to 500mm on tankers depending on cargo grade and vessel size, and rated to the cargo system's design pressure.
Actuator
Hydraulic or pneumatic actuators are standard on larger tankers so the valve can be closed quickly from the cargo control room in an emergency shutdown sequence; smaller vessels may still use hand-operated valves.
Read the full guide
Position indication
Local and remote indicators showing open, closed or intermediate position, feeding the cargo control system so the operator knows the valve state without walking to the manifold.
Spectacle blind or spade
A removable blanking plate fitted just inboard of the valve, used to positively isolate the cargo system for maintenance or when a grade change makes cross-contamination a risk, since a closed valve alone is not always accepted as a positive isolation.
Selection and Sizing
Bore and pressure rating follow the cargo pumping rate the terminal expects and the cargo system's design pressure, while material selection, carbon steel, stainless steel, or a lined valve for corrosive or high-purity cargoes, follows the cargo grades the vessel actually carries. Actuator response time is specified against the emergency shutdown time the terminal and the ship's Ship/Shore Safety Checklist require, commonly a matter of seconds for the final closing stage.
Regulations and Class
MARPOL Annex I and II set requirements around cargo and bunker transfer arrangements including manifold drip trays and spill containment; class rules cover valve pressure testing and material certification for the cargo system. Emergency shutdown requirements linking the manifold valve to a ship/shore link are increasingly specified by terminals and, for gas carriers, referenced in the IGC Code, even where not universally mandated by flag state.
Typical Faults
- An actuator hydraulic or pneumatic supply leak slows or prevents emergency closure exactly when speed matters most.
- Disc or seat wear from repeated cycling and abrasive cargo residue leads to a valve that will not seal fully closed, risking a slow leak past a closed valve.
- A position indicator out of calibration can show closed on the panel when the valve disc is still partly open, a dangerous mismatch during a transfer.
- Corrosion of the spectacle blind or its fasteners from being left in one position too long makes it difficult to swap when a grade change actually requires it.
What to Look for in a Supplier
- Material certification traceable to the cargo grades the vessel trades, especially for corrosive or high-purity cargoes.
- Actuator response time tested and documented against the ship's emergency shutdown requirement.
- Spare parts availability for seats and seals specifically, since these wear faster than the valve body itself.
Never treat a closed manifold valve as a positive isolation on its own: fit the spectacle blind or spade whenever the job, maintenance, grade change or dry-docking, calls for a guaranteed no-flow condition, because a valve can leak past its seat without any visible sign at the flange.
Models in this type.
The best-documented model of each manufacturer first, then the next — 1 of 1 models in Manifold Valve. Every row links to full specifications, documents and service notes.
Manufacturers.
All 12 manufacturers with models of Manifold Valve. Names with a manufacturer page open it; the others open a search across the full library.
All manufacturersAlso in Cargo Hoses & Manifolds.
The other equipment types in this category.
One request. A person reads it and replies by e-mail.
Tell us the manufacturer, the model and what you need — a part, a service call, a second opinion. A person reads every request and replies by e-mail.
No details at hand? A photo of the rating plate or the part is enough — simply attach it to the request.
Three things people ask first.
Is Manifold Valve data free?
Yes. Every model page, every guide and every datasheet for this type is readable without an account. An account adds saved searches and requests, nothing is taken away.
My model is missing — what now?
Send us the nameplate. We identify it by hand, add it to the library, and if you need a part or a service, the request is already on our desk.
Can you source a Manifold Valve part?
Yes. Tell us the manufacturer, the model and what you need — a person reads every request and replies by e-mail.