Wheeled Extinguisher
A wheeled extinguisher is a large-capacity, trolley-mounted extinguisher for hazards too big for a handheld unit, typically 50-150 kg of agent, moved to the fire on its own wheels rather than fixed in place or carried by one person.
What to check on a Wheeled Extinguisher.
3 models from Amerex in Wheeled Extinguisher. Below: the full model list.
What sets a wheeled extinguisher apart
A handheld portable extinguisher holds a few kilograms of agent and is meant to be grabbed and used within seconds by one person. A wheeled extinguisher is a different class of equipment entirely: a cylinder of 50 kg or more, sometimes well over 100 kg, mounted on a two-wheel trolley with its own hose reel, meant to be pushed to a fire that a handheld unit cannot handle — a large deck fire, an engine room bilge fire, or a hazard at a fixed high-risk location such as a paint locker or a bunker station. It sits between the handheld extinguisher and a fixed system: faster to bring into action than rigging a fire hose from the main, with far more agent and throw range than anything one person can carry. Because of its size, positioning matters as much as capacity — a wheeled unit stowed where it cannot be manoeuvred to the hazard in time is no better than none at all.
Legend
- cylinder valve
- towing handle
- agent cylinder
- carrying handle
- hose and discharge nozzle
- wheeled frame
- wheels
Main components
- Cylinder — pressure vessel holding the extinguishing agent, dry powder, CO2 or foam depending on the hazard it protects
- Trolley and wheels — frame built to move the loaded unit over deck plating and coamings without tipping
- Hose and nozzle — longer hose than a handheld unit, reeled, with a control valve at the nozzle so discharge can be stopped and restarted
- Pressure gauge or indicator — shows charge state at a glance, critical given how rarely these units are actually discharged
- Propellant — either stored pressure or a separate CO2 cartridge, depending on agent type
Selection and sizing
- Agent type matched to the hazard class at the location it protects — dry powder for flammable liquid and electrical hazards, foam for flammable liquid spill fires, CO2 where a clean, non-conductive agent is needed
- Agent quantity against the fire risk assessment for that location, not a blanket figure for the whole ship
- Discharge time and throw range needed to keep the operator at a safe distance from the hazard it is meant to cover
- Trolley mobility over the actual deck surfaces and thresholds between the stowage position and the protected area
Regulations and class
SOLAS Chapter II-2 and the associated Fire Safety Systems Code set requirements for portable and wheeled fire-fighting appliances, including where wheeled extinguishers are mandated (engine rooms above a certain size, near bunker stations, in paint stores) and their minimum agent quantities. Class and flag state surveys check that units are in date, correctly charged, and stowed at their approved location rather than moved elsewhere for convenience.
Typical faults
| Fault | Cause | Consequence |
|---|---|---|
| Low or lost pressure charge | Slow leakage past valve seals over years without use | Unit fails to discharge or discharges weakly when actually needed |
| Caked dry powder agent | Moisture ingress into the cylinder over time | Powder fails to fluidise and discharge cleanly through the hose |
| Seized or damaged wheels | Corrosion or physical damage from cargo operations nearby | Unit cannot be moved quickly to the fire location |
| Unit stowed away from its designated position | Moved temporarily during maintenance work and not returned | Delay finding the unit, or the protected hazard left effectively uncovered |
What to look for in a supplier
- Agent and cylinder approval matching the flag state and class requirements for the specific hazard location
- A hose and nozzle assembly rated for the full charge pressure with a shut-off at the nozzle
- Servicing and refill support reachable from the ship's actual trading ports, since wheeled units need specialist recharge equipment
- Trolley construction suited to the deck conditions where the unit will actually be stowed and moved
Check the pressure gauge and inspect for caking on the routine rounds, not only at the annual service — a wheeled extinguisher that has sat untouched for years is exactly the one most likely to fail silently.
Models in this type.
The best-documented model of each manufacturer first, then the next — 3 of 3 models in Wheeled Extinguisher. Every row links to full specifications, documents and service notes.
Manufacturers.
All 10 manufacturers with models of Wheeled Extinguisher. Names with a manufacturer page open it; the others open a search across the full library.
All manufacturers in the libraryAlso in Portable Fire Extinguishers.
The other equipment types in this category.
Write to us about this model — the answer comes by e-mail.
Name the make and the model and what the job is: a spare, a service call, a second opinion on a data sheet. We answer by e-mail.
No details at hand? A photo of the rating plate or the part is enough — simply attach it to the request.
Questions that come up with this equipment.
Is Wheeled Extinguisher data free?
Yes. Every model page, every guide and every datasheet for this type is readable without an account. An account adds saved searches and requests, nothing is taken away.
My model is missing — what now?
Send us the nameplate. We identify it by hand, add it to the library, and if you need a part or a service, the request is already on our desk.
Can you source a Wheeled Extinguisher part?
Yes. Tell us the manufacturer, the model and what you need — a person reads every request and replies by e-mail.