Freefall Launch Platform
A freefall lifeboat leaves its stern ramp under its own weight and hits the water in free fall, a deliberately aggressive launch designed for the moment a crew cannot safely stand at davits to lower a boat under control.
What to check on a Freefall Launch Platform.
1 models from MacGregor in Freefall Launch Platform. Below: the full model list.
What makes a freefall launch platform different from a gravity davit
A gravity davit lowers a lifeboat on wire falls, under a winch brake, at a controlled speed the whole way to the water. A freefall arrangement does something deliberately more aggressive: the lifeboat sits on an inclined ramp at the stern, held by a single release hook, and when that hook is triggered from inside the boat the boat slides down the ramp under its own weight and leaves the ramp end in free fall, hitting the water bow-first with enough momentum to drive itself clear of the ship's side before the engine is even started. That design exists specifically for the worst case, a ship on fire, listing, or still making way, where crew cannot safely stand at davits to lower a boat under control and need to get away in one uninterrupted motion. Occupants are secured in seats with harnesses because the fall and water entry produce real deceleration loads that a standing or unsecured occupant would not survive well.
Legend
- deck / stern
- structure
- ramp incline
- lifeboat
- release hook (bow)
- release control (inside boat)
- cradle / skid
- sea level
Main components
Ramp and cradle
A fixed, angled steel ramp at the stern with a cradle or skid that holds the boat in its stowed position and guides it during the slide, angled and finished to give the boat the release speed the type approval testing was based on.
Release mechanism
A single on-load release hook holding the boat at the top of the ramp, triggered by a control inside the boat itself, deliberately kept independent of any winch or wire system so a power or hydraulic failure elsewhere on the launching appliance cannot prevent release.
Read the full guide
Secondary lowering arrangement
Many installations also provide a davit-launch or lowering mode using the same appliance, allowing the boat to be lowered under winch control for training, maintenance recovery, or a controlled launch when freefall conditions are not needed, without altering the primary freefall capability.
Retrieval winch
A powered winch and wire system to recover the boat back up the ramp after use or drill, separate in function from the release mechanism even where they share some structure.
Securing gripes and hydraulic dampers
Gripes or lashings hold the boat firmly on the ramp against ship motion at sea, released as part of the launch sequence, while some installations include a hydraulic damper at the ramp end to manage the transition from slide to free fall consistently regardless of sea state.
Selection and sizing
Ramp angle and length, boat weight, and the height of the stern above the waterline are all fixed together during type approval testing, so a freefall boat and its launching appliance are certified as a matched set rather than components chosen independently. Selecting a system means matching boat capacity to the complement it must carry, and checking that the vessel's actual freeboard at the stern falls within the range the appliance and boat were tested for, since a mismatch changes the entry speed and angle the boat was designed around.
Regulations and class
The LSA Code sets the design, testing and launching performance requirements for freefall lifeboats and their launching appliances, including the drop test height and entry conditions the combination must be proven against before certification. Class surveys require periodic winch load testing, release gear function tests, and a full launch drill at intervals set by SOLAS and the LSA Code, with the on-load release hook specifically checked for free and correct operation since a hook that will not release under load defeats the entire system.
Typical faults
| Fault | Consequence |
|---|---|
| Release hook corroded or seized from infrequent full-load testing | Boat fails to release when triggered, defeating the one function the system exists for |
| Ramp surface fouled, corroded or coated unevenly | Boat does not reach the release speed the design was tested for, changing water entry behaviour |
| Retrieval winch wire or hydraulics neglected between drills | Boat cannot be recovered after a drill or maintenance launch, taking the lifesaving appliance out of service |
| Gripes or lashings incorrectly re-secured after a drill | Boat not properly restrained at sea, risking damage or premature release in heavy weather |
What to look for in a supplier
- Boat and launching appliance supplied and certified as a matched, type-approved set, since substituting components from different manufacturers can void the approval basis
- Documented ramp angle and freeboard compatibility for the specific vessel, not a generic installation drawing
- Full-load release hook testing included as standard commissioning and periodic service, not left to the crew to arrange separately
- Accessible, serviceable retrieval winch arrangement, since a system that is hard to service after a drill discourages the regular drilling the crew actually needs
Insist on seeing the on-load release hook exercised under actual load during commissioning, not just cycled by hand with the boat empty, because a hook that moves freely with no load can still bind under the boat's full weight.
Models in this type.
The best-documented model of each manufacturer first, then the next — 1 of 1 models in Freefall Launch Platform. Every row links to full specifications, documents and service notes.
Manufacturers.
All 2 manufacturers with models of Freefall Launch Platform. Names with a manufacturer page open it; the others open a search across the full library.
All manufacturers in the libraryAlso in Davits.
The other equipment types in this category.
Write to us about your machine — the answer comes by e-mail.
Name the make and the model and what the job is: a spare, a service call, a second opinion on a data sheet. We answer by e-mail.
No details at hand? A photo of the rating plate or the part is enough — simply attach it to the request.
Questions that come up with this equipment.
Is Freefall Launch Platform data free?
Yes. Every model page, every guide and every datasheet for this type is readable without an account. An account adds saved searches and requests, nothing is taken away.
My model is missing — what now?
Send us the nameplate. We identify it by hand, add it to the library, and if you need a part or a service, the request is already on our desk.
Can you source a Freefall Launch Platform part?
Yes. Tell us the manufacturer, the model and what you need — a person reads every request and replies by e-mail.