Dishwasher
medium
132 / 132 models (Inspector)
Commercial dishwashers on board run the same rack-and-spray principle as ashore but add a stainless build against salt air, a fresh-water final rinse independent of any recirculated tank, and a duty cycle sized for a fixed crew sitting rather than a variable restaurant flow.
Read more — Dishwasher explained ▾
What sets a marine dishwasher apart
A galley dishwasher at sea does the same job as a commercial unit ashore, a wash cycle followed by a hot final rinse to sanitise crockery and cutlery, but it is built and operated differently. It has to survive continuous vibration and rolling motion without door seals working loose, its drain and supply connections are fixed piping rather than a floor gully, and it usually runs a known number of cycles per meal sitting for a fixed crew count rather than a variable commercial covers count. Many units are single-tank hood or rack types rather than the flight or conveyor machines found in shore catering, because galley space and crew numbers rarely justify anything larger.
Main components
Wash tank and pump
A recirculating pump draws detergent solution from the tank and sprays it through upper and lower rotating arms. Tank heating is usually electric, sometimes with a steam coil on vessels that already run a steam plant for the galley.
Final rinse system
A separate booster heater raises rinse water to 82-88 degrees C for the final sanitising rinse, drawn fresh each cycle rather than recirculated, which is what actually controls bacteria rather than the wash cycle itself.
Door and seal arrangement
Hood-type machines lift by hand or motor; door-type machines seal with a gasket that is the single most common wear item on board due to constant thermal cycling and vibration loosening hinges over time.
Detergent and rinse-aid dosing
Peristaltic dosing pumps meter detergent and rinse aid per cycle; calibration drifts over months and is rarely checked unless wash results visibly deteriorate.
Selection and sizing
- Cycles per hour needed against crew size and meal sitting length; a 90-second to 2-minute cycle machine copes with most crew complements under 40.
- Fresh water and electrical supply available, since the booster heater alone can draw several kilowatts.
- Rack size against the vessel's crockery and galley tray standard.
- Corrosion-resistant grade of stainless steel for the tank and frame, given the humid, salty galley atmosphere.
Typical faults
| Fault | Cause | Consequence |
|---|---|---|
| Cloudy or spotted glassware | Rinse-aid dosing pump empty or miscalibrated | Fails visual hygiene check, crew complaints |
| Poor wash results | Blocked spray arm jets from food debris | Items returned for rewash, extra water and power use |
| Rinse temperature not reached | Scaled booster heater element | Sanitising rinse below target, hygiene risk |
| Door seal leak | Gasket hardened or hinge misaligned from vibration | Water on galley deck, slip hazard |
What to look for in a supplier
- Spare gaskets, spray arms and heating elements held as standard stock rather than made to order.
- A booster heater with a descaling routine suited to the feed water quality expected on board, since RO permeate and shore water differ in hardness.
- A control panel that survives galley humidity; a sealed membrane keypad outlasts an unsealed switch by a wide margin.
Descale the booster heater on a fixed calendar rather than waiting for the rinse temperature alarm; by the time the alarm trips, scale has usually already cut heater life and the sanitising rinse has been under-temperature for weeks.
8 manufacturers · 132 models
Winterhalter Marine
36
UC-S Marine electric
unverified
· 6.0 kW
Power (kW)
6
Voltage (V)
400
Capacity
6 GN 1/1
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
UC-S Marine gas
unverified
· 6.0 kW
Power (kW)
6
Voltage (V)
400
Capacity
6 GN 1/1
Fuel
gas
Common Failures & Inspection Points
- Scale, grease or food residue restricts water, air or heat transfer and causes poor performance
- Door seals, valves or hose connections can leak, noticed as water, air or temperature loss
- Heating, refrigeration or motor components can fail, noticed as inability to reach operating condition
- Temperature, level or door sensors can drift or fail and cause alarms or interrupted cycles
- Corroded electrical connections or moisture ingress can cause intermittent operation or protective trips
Service: Keep food-contact and ventilation surfaces clean, inspect seals, filters, drains and electrical condition and verify safe operation of doors and guards. Function-test heating, cooling, wash or extraction modes applicable to the appliance. Exact temperatures, cleaning chemicals and electrical test values must follow the appliance manufacturer documentation and onboard hygiene procedures.
Spare Parts: Typical spares include door gaskets, filters, spray or drain parts, lamps or indicators, thermostats or sensors, heating elements or contactors and service seals appropriate to the appliance.
Use Cases: Used in merchant, passenger, offshore and service vessels for onboard catering, food storage and galley operations.
UC-M Marine electric
unverified
· 6.0 kW
Power (kW)
6
Voltage (V)
400
Capacity
6 GN 1/1
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
UC-M Marine gas
unverified
· 6.0 kW
Power (kW)
6
Voltage (V)
400
Capacity
6 GN 1/1
Fuel
gas
Common Failures & Inspection Points
- Scale, grease or food residue restricts water, air or heat transfer and causes poor performance
- Door seals, valves or hose connections can leak, noticed as water, air or temperature loss
- Heating, refrigeration or motor components can fail, noticed as inability to reach operating condition
- Temperature, level or door sensors can drift or fail and cause alarms or interrupted cycles
- Corroded electrical connections or moisture ingress can cause intermittent operation or protective trips
Service: Keep food-contact and ventilation surfaces clean, inspect seals, filters, drains and electrical condition and verify safe operation of doors and guards. Function-test heating, cooling, wash or extraction modes applicable to the appliance. Exact temperatures, cleaning chemicals and electrical test values must follow the appliance manufacturer documentation and onboard hygiene procedures.
Spare Parts: Typical spares include door gaskets, filters, spray or drain parts, lamps or indicators, thermostats or sensors, heating elements or contactors and service seals appropriate to the appliance.
Use Cases: Used in merchant, passenger, offshore and service vessels for onboard catering, food storage and galley operations.
UC-L Marine electric
unverified
· 6.0 kW
Power (kW)
6
Voltage (V)
400
Capacity
6 GN 1/1
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
UC-L Marine gas
unverified
· 6.0 kW
Power (kW)
6
Voltage (V)
400
Capacity
6 GN 1/1
Fuel
gas
Common Failures & Inspection Points
- Scale, grease or food residue restricts water, air or heat transfer and causes poor performance
- Door seals, valves or hose connections can leak, noticed as water, air or temperature loss
- Heating, refrigeration or motor components can fail, noticed as inability to reach operating condition
- Temperature, level or door sensors can drift or fail and cause alarms or interrupted cycles
- Corroded electrical connections or moisture ingress can cause intermittent operation or protective trips
Service: Keep food-contact and ventilation surfaces clean, inspect seals, filters, drains and electrical condition and verify safe operation of doors and guards. Function-test heating, cooling, wash or extraction modes applicable to the appliance. Exact temperatures, cleaning chemicals and electrical test values must follow the appliance manufacturer documentation and onboard hygiene procedures.
Spare Parts: Typical spares include door gaskets, filters, spray or drain parts, lamps or indicators, thermostats or sensors, heating elements or contactors and service seals appropriate to the appliance.
Use Cases: Used in merchant, passenger, offshore and service vessels for onboard catering, food storage and galley operations.
UC-XL Marine electric
unverified
· 6.0 kW
Power (kW)
6
Voltage (V)
400
Capacity
6 GN 1/1
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
UC-XL Marine gas
unverified
· 6.0 kW
Power (kW)
6
Voltage (V)
400
Capacity
6 GN 1/1
Fuel
gas
Common Failures & Inspection Points
- Scale, grease or food residue restricts water, air or heat transfer and causes poor performance
- Door seals, valves or hose connections can leak, noticed as water, air or temperature loss
- Heating, refrigeration or motor components can fail, noticed as inability to reach operating condition
- Temperature, level or door sensors can drift or fail and cause alarms or interrupted cycles
- Corroded electrical connections or moisture ingress can cause intermittent operation or protective trips
Service: Keep food-contact and ventilation surfaces clean, inspect seals, filters, drains and electrical condition and verify safe operation of doors and guards. Function-test heating, cooling, wash or extraction modes applicable to the appliance. Exact temperatures, cleaning chemicals and electrical test values must follow the appliance manufacturer documentation and onboard hygiene procedures.
Spare Parts: Typical spares include door gaskets, filters, spray or drain parts, lamps or indicators, thermostats or sensors, heating elements or contactors and service seals appropriate to the appliance.
Use Cases: Used in merchant, passenger, offshore and service vessels for onboard catering, food storage and galley operations.
PT-500 Marine electric
unverified
· 6.0 kW
Power (kW)
6
Voltage (V)
400
Capacity
6 GN 1/1
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
PT-500 Marine gas
unverified
· 6.0 kW
Power (kW)
6
Voltage (V)
400
Capacity
6 GN 1/1
Fuel
gas
Common Failures & Inspection Points
- Heating or drive component failure caused by wear, overheating or electrical faults, resulting in slow operation, no heat or inability to complete the normal cycle
- Temperature, level or control-sensor malfunction caused by drift or component failure, resulting in unstable operation, alarms or incorrect temperature
- Door, lid, seal or duct deterioration caused by repeated use and heat, resulting in leakage, heat loss or poor extraction
- Electrical-control fault caused by moisture, loose terminals or failed relays, resulting in intermittent operation or breaker trips
- Drain, filter, grease path or ventilation restriction where applicable caused by food deposits or poor cleaning, resulting in leakage, odor, overheating or reduced performance
Service: Keep heating surfaces, filters, drains, grease paths and ventilation openings clean as applicable to the appliance. Inspect electrical terminals, controls, doors, guards and safety interlocks for heat damage or looseness. Verify temperature or cycle control using the vessel's approved maintenance method and investigate repeated overheating or breaker trips. Check secure fastening to the galley structure and inspect flexible service connections where fitted. Use cleaning chemicals compatible with stainless steel, seals and heating components. Refer to manufacturer documentation for exact electrical ratings, calibration procedures and service limits.
Spare Parts: Keep door or lid seals, thermostats or temperature sensors, selected heating elements, pumps or fans where applicable, fuses, switches and manufacturer-recommended control parts. High-use passenger vessels may justify additional wear components. Verify all electrical and mechanical parts against the appliance nameplate.
Use Cases: Food preparation, cleaning and catering service in merchant-ship, ferry, cruise-ship and offshore galley installations.
PT-700 Marine electric
unverified
· 6.0 kW
Power (kW)
6
Voltage (V)
400
Capacity
6 GN 1/1
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
PT-700 Marine gas
unverified
· 6.0 kW
Power (kW)
6
Voltage (V)
400
Capacity
6 GN 1/1
Fuel
gas
Common Failures & Inspection Points
- Heating or drive component failure caused by wear, overheating or electrical faults, resulting in slow operation, no heat or inability to complete the normal cycle
- Temperature, level or control-sensor malfunction caused by drift or component failure, resulting in unstable operation, alarms or incorrect temperature
- Door, lid, seal or duct deterioration caused by repeated use and heat, resulting in leakage, heat loss or poor extraction
- Electrical-control fault caused by moisture, loose terminals or failed relays, resulting in intermittent operation or breaker trips
- Drain, filter, grease path or ventilation restriction where applicable caused by food deposits or poor cleaning, resulting in leakage, odor, overheating or reduced performance
Service: Keep heating surfaces, filters, drains, grease paths and ventilation openings clean as applicable to the appliance. Inspect electrical terminals, controls, doors, guards and safety interlocks for heat damage or looseness. Verify temperature or cycle control using the vessel's approved maintenance method and investigate repeated overheating or breaker trips. Check secure fastening to the galley structure and inspect flexible service connections where fitted. Use cleaning chemicals compatible with stainless steel, seals and heating components. Refer to manufacturer documentation for exact electrical ratings, calibration procedures and service limits.
Spare Parts: Keep door or lid seals, thermostats or temperature sensors, selected heating elements, pumps or fans where applicable, fuses, switches and manufacturer-recommended control parts. High-use passenger vessels may justify additional wear components. Verify all electrical and mechanical parts against the appliance nameplate.
Use Cases: Food preparation, cleaning and catering service in merchant-ship, ferry, cruise-ship and offshore galley installations.
PT-M Marine electric
unverified
· 6.0 kW
Power (kW)
6
Voltage (V)
400
Capacity
6 GN 1/1
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
PT-M Marine gas
unverified
· 6.0 kW
Power (kW)
6
Voltage (V)
400
Capacity
6 GN 1/1
Fuel
gas
Common Failures & Inspection Points
- Scale, grease or food residue restricts water, air or heat transfer and causes poor performance
- Door seals, valves or hose connections can leak, noticed as water, air or temperature loss
- Heating, refrigeration or motor components can fail, noticed as inability to reach operating condition
- Temperature, level or door sensors can drift or fail and cause alarms or interrupted cycles
- Corroded electrical connections or moisture ingress can cause intermittent operation or protective trips
Service: Keep food-contact and ventilation surfaces clean, inspect seals, filters, drains and electrical condition and verify safe operation of doors and guards. Function-test heating, cooling, wash or extraction modes applicable to the appliance. Exact temperatures, cleaning chemicals and electrical test values must follow the appliance manufacturer documentation and onboard hygiene procedures.
Spare Parts: Typical spares include door gaskets, filters, spray or drain parts, lamps or indicators, thermostats or sensors, heating elements or contactors and service seals appropriate to the appliance.
Use Cases: Used in merchant, passenger, offshore and service vessels for onboard catering, food storage and galley operations.
MT-M Marine electric
unverified
· 6.0 kW
Power (kW)
6
Voltage (V)
400
Capacity
6 GN 1/1
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
MT-M Marine gas
unverified
· 6.0 kW
Power (kW)
6
Voltage (V)
400
Capacity
6 GN 1/1
Fuel
gas
Common Failures & Inspection Points
- Scale, grease or food residue restricts water, air or heat transfer and causes poor performance
- Door seals, valves or hose connections can leak, noticed as water, air or temperature loss
- Heating, refrigeration or motor components can fail, noticed as inability to reach operating condition
- Temperature, level or door sensors can drift or fail and cause alarms or interrupted cycles
- Corroded electrical connections or moisture ingress can cause intermittent operation or protective trips
Service: Keep food-contact and ventilation surfaces clean, inspect seals, filters, drains and electrical condition and verify safe operation of doors and guards. Function-test heating, cooling, wash or extraction modes applicable to the appliance. Exact temperatures, cleaning chemicals and electrical test values must follow the appliance manufacturer documentation and onboard hygiene procedures.
Spare Parts: Typical spares include door gaskets, filters, spray or drain parts, lamps or indicators, thermostats or sensors, heating elements or contactors and service seals appropriate to the appliance.
Use Cases: Used in merchant, passenger, offshore and service vessels for onboard catering, food storage and galley operations.
MTR Marine electric
unverified
· 6.0 kW
Power (kW)
6
Voltage (V)
400
Capacity
6 GN 1/1
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
MTR Marine gas
unverified
· 6.0 kW
Power (kW)
6
Voltage (V)
400
Capacity
6 GN 1/1
Fuel
gas
Common Failures & Inspection Points
- Spray-arm or nozzle blockage reduces washing performance and leaves food or detergent residue
- Heating-element or thermostat failure causes poor wash or rinse temperature and cycle alarms
- Pump wear or seal leakage causes weak circulation, abnormal noise or water leakage
- Door-switch or safety-interlock failure prevents a cycle from starting or causes nuisance stoppage
- Scale, detergent buildup or drain blockage causes poor rinsing, slow draining or flooding
Service: Inspect spray arms, filters, pumps, heaters, door seals, safety switches, dosing equipment and drains. Remove scale using approved methods and verify secure electrical and water connections. Check for leaks and overheating at terminals. Refer to manufacturer documentation for exact detergent, temperature and service settings.
Spare Parts: Carry pump seals, door seals, spray nozzles, heater or thermostat parts, drain-valve components, filters, fuses and control relays.
Use Cases: Commercial ship galleys, passenger-service areas and offshore accommodation facilities.
STR-110 Marine electric
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
400
Capacity
10 GN 1/1
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner or thermostat faults caused by ageing, contamination or control failure can result in slow heating, overheating or failure to reach operating condition
- Door, seal or gasket deterioration caused by heat and repeated use can cause heat loss, steam leakage or poor washing performance
- Drain, spray or filter blockage caused by food debris or scale can produce poor cleaning, standing water or overflow
- Switch, contactor or control-board faults caused by moisture or component wear can lead to intermittent operation or failure to start
- Ventilation or cooling obstruction caused by grease or dust can increase appliance temperature and cause nuisance trips or component damage
Service: Inspect cleanliness, guards, wiring, controls, seals, drains, ventilation and utility connections. Confirm safety cut-outs and protective devices operate without bypassing them, and remove grease or scale according to the maker's procedure. Refer to manufacturer documentation for exact electrical, gas, temperature and service values.
Spare Parts: Useful spares include seals, heating or control components, filters, switches, contactors, fuses, spray or drain parts and other maker-approved consumables suited to the appliance.
Use Cases: Merchant, passenger, ferry and offshore-vessel galleys and catering spaces.
STR-110 Marine gas
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
400
Capacity
10 GN 1/1
Fuel
gas
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
STR-130 Marine electric
unverified
· 6.0 kW
Power (kW)
6
Voltage (V)
400
Capacity
6 GN 1/1
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
STR-130 Marine gas
unverified
· 6.0 kW
Power (kW)
6
Voltage (V)
400
Capacity
6 GN 1/1
Fuel
gas
Common Failures & Inspection Points
- Heating, cooling or drive-component failure causes poor performance, slow cycles or inability to operate
- Temperature sensor, thermostat or control faults cause unstable operation or protective shutdown
- Door seal, hose, drain or valve deterioration causes leakage, heat loss or water accumulation
- Fan, pump, motor or bearing wear causes abnormal noise, reduced circulation or vibration
- Electrical, ignition or safety-interlock faults cause failed starts, nuisance trips or error indications
Service: Inspect seals, controls, heaters or refrigeration components, pumps or fans, water and drain connections, ventilation and secure mounting according to the appliance type. Clean grease, lint, scale or food residues from approved areas. Verify safety interlocks and look for heat-damaged wiring. Refer to the manufacturer documentation for the exact figure for temperature, loading and service criteria.
Spare Parts: Carry seals, sensors, fuses, control relays, pump or fan parts, heating or ignition components and appliance-specific consumables.
Use Cases: Galley, pantry, accommodation and laundry service on merchant, passenger and offshore vessels.
STR-155 Marine electric
unverified
· 6.0 kW
Power (kW)
6
Voltage (V)
400
Capacity
6 GN 1/1
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
STR-155 Marine gas
unverified
· 6.0 kW
Power (kW)
6
Voltage (V)
400
Capacity
6 GN 1/1
Fuel
gas
Common Failures & Inspection Points
- Heating, cooling or drive-component failure causes poor performance, slow cycles or inability to operate
- Temperature sensor, thermostat or control faults cause unstable operation or protective shutdown
- Door seal, hose, drain or valve deterioration causes leakage, heat loss or water accumulation
- Fan, pump, motor or bearing wear causes abnormal noise, reduced circulation or vibration
- Electrical, ignition or safety-interlock faults cause failed starts, nuisance trips or error indications
Service: Inspect seals, controls, heaters or refrigeration components, pumps or fans, water and drain connections, ventilation and secure mounting according to the appliance type. Clean grease, lint, scale or food residues from approved areas. Verify safety interlocks and look for heat-damaged wiring. Refer to the manufacturer documentation for the exact figure for temperature, loading and service criteria.
Spare Parts: Carry seals, sensors, fuses, control relays, pump or fan parts, heating or ignition components and appliance-specific consumables.
Use Cases: Galley, pantry, accommodation and laundry service on merchant, passenger and offshore vessels.
Dishwasher Small 230V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
230
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Loss of electrical, hydraulic, pneumatic, fluid, or other service supply from a protection trip, leakage, blockage, or upstream fault results in failed starting or loss of function
- Mechanical wear, corrosion, fouling, or contamination of moving and wetted parts causes increased noise, leakage, sticking, vibration, or reduced performance
- Seal, gasket, hose, cable, or connection deterioration from age, heat, vibration, or environmental exposure produces visible leakage, intermittent signals, or loss of pressure
- Sensor, switch, actuator, relay, or control-system faults cause incorrect indication, nuisance alarms, failed automatic sequences, or loss of remote control
- Incorrect adjustment, assembly, or maintenance leads to unstable operation, recurrent alarms, or performance that differs from the vessel's normal baseline
Service: Inspect the unit for leakage, corrosion, contamination, loose connections, abnormal noise or vibration, condition of guards and mountings, service supplies, controls, alarms, and functional performance. Use maintenance history to identify deterioration trends and refer to manufacturer documentation for exact settings, tolerances, test values, and overhaul criteria.
Spare Parts: Keep the manufacturer-recommended seals and gaskets, filters where fitted, fuses or protection items, common sensors and switches, and critical actuator, control, or wear components appropriate to the installed configuration. Exact part numbers and quantities must come from the manufacturer spare-parts documentation.
Use Cases: Used on vessel types fitted with galley & domestic equipment, including merchant, offshore, passenger, fishing, or workboat installations where this specific dishwasher duty is required.
Dishwasher Small 400V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
400
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Loss of electrical, hydraulic, pneumatic, fluid, or other service supply from a protection trip, leakage, blockage, or upstream fault results in failed starting or loss of function
- Mechanical wear, corrosion, fouling, or contamination of moving and wetted parts causes increased noise, leakage, sticking, vibration, or reduced performance
- Seal, gasket, hose, cable, or connection deterioration from age, heat, vibration, or environmental exposure produces visible leakage, intermittent signals, or loss of pressure
- Sensor, switch, actuator, relay, or control-system faults cause incorrect indication, nuisance alarms, failed automatic sequences, or loss of remote control
- Incorrect adjustment, assembly, or maintenance leads to unstable operation, recurrent alarms, or performance that differs from the vessel's normal baseline
Service: Inspect the unit for leakage, corrosion, contamination, loose connections, abnormal noise or vibration, condition of guards and mountings, service supplies, controls, alarms, and functional performance. Use maintenance history to identify deterioration trends and refer to manufacturer documentation for exact settings, tolerances, test values, and overhaul criteria.
Spare Parts: Keep the manufacturer-recommended seals and gaskets, filters where fitted, fuses or protection items, common sensors and switches, and critical actuator, control, or wear components appropriate to the installed configuration. Exact part numbers and quantities must come from the manufacturer spare-parts documentation.
Use Cases: Used on vessel types fitted with galley & domestic equipment, including merchant, offshore, passenger, fishing, or workboat installations where this specific dishwasher duty is required.
Dishwasher Small 440V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
440
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Loss of electrical, hydraulic, pneumatic, fluid, or other service supply from a protection trip, leakage, blockage, or upstream fault results in failed starting or loss of function
- Mechanical wear, corrosion, fouling, or contamination of moving and wetted parts causes increased noise, leakage, sticking, vibration, or reduced performance
- Seal, gasket, hose, cable, or connection deterioration from age, heat, vibration, or environmental exposure produces visible leakage, intermittent signals, or loss of pressure
- Sensor, switch, actuator, relay, or control-system faults cause incorrect indication, nuisance alarms, failed automatic sequences, or loss of remote control
- Incorrect adjustment, assembly, or maintenance leads to unstable operation, recurrent alarms, or performance that differs from the vessel's normal baseline
Service: Inspect the unit for leakage, corrosion, contamination, loose connections, abnormal noise or vibration, condition of guards and mountings, service supplies, controls, alarms, and functional performance. Use maintenance history to identify deterioration trends and refer to manufacturer documentation for exact settings, tolerances, test values, and overhaul criteria.
Spare Parts: Keep the manufacturer-recommended seals and gaskets, filters where fitted, fuses or protection items, common sensors and switches, and critical actuator, control, or wear components appropriate to the installed configuration. Exact part numbers and quantities must come from the manufacturer spare-parts documentation.
Use Cases: Used on vessel types fitted with galley & domestic equipment, including merchant, offshore, passenger, fishing, or workboat installations where this specific dishwasher duty is required.
Dishwasher Medium 230V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
230
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating, refrigeration or motor element failure, typically indicated by loss of temperature control, inability to operate or protective trip
- Thermostat/sensor/control fault, typically indicated by incorrect temperature, nuisance alarms or unstable cycling
- Water, drain or door-seal leakage where applicable, typically indicated by leaks, poor cleaning performance or condensation
- Fan, pump or compressor wear where fitted, typically indicated by noise, reduced performance or trip alarms
- Grease/dirt accumulation or blocked filters, typically indicated by reduced airflow, overheating, odor or hygiene issues
Service: Inspect electrical safety, controls, thermostats, seals, drains, filters, fans/pumps/compressors as applicable, ventilation and cleanliness; exact operating temperatures and service limits come from manufacturer documentation.
Spare Parts: Keep door seals, heating elements or thermostats, filters, relays/contactors, pumps/fans and appliance-specific wear parts for critical galley equipment.
Use Cases: Used in ship galleys and domestic spaces on merchant, passenger, offshore and naval vessels. This entry applies specifically to the Dishwasher variant identified as Winterhalter Marine Dishwasher Medium 230V Marine.
Dishwasher Medium 400V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
400
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating, refrigeration or motor element failure, typically indicated by loss of temperature control, inability to operate or protective trip
- Thermostat/sensor/control fault, typically indicated by incorrect temperature, nuisance alarms or unstable cycling
- Water, drain or door-seal leakage where applicable, typically indicated by leaks, poor cleaning performance or condensation
- Fan, pump or compressor wear where fitted, typically indicated by noise, reduced performance or trip alarms
- Grease/dirt accumulation or blocked filters, typically indicated by reduced airflow, overheating, odor or hygiene issues
Service: Inspect electrical safety, controls, thermostats, seals, drains, filters, fans/pumps/compressors as applicable, ventilation and cleanliness; exact operating temperatures and service limits come from manufacturer documentation.
Spare Parts: Keep door seals, heating elements or thermostats, filters, relays/contactors, pumps/fans and appliance-specific wear parts for critical galley equipment.
Use Cases: Used in ship galleys and domestic spaces on merchant, passenger, offshore and naval vessels. This entry applies specifically to the Dishwasher variant identified as Winterhalter Marine Dishwasher Medium 400V Marine.
Dishwasher Medium 440V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
440
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating, refrigeration or motor element failure, typically indicated by loss of temperature control, inability to operate or protective trip
- Thermostat/sensor/control fault, typically indicated by incorrect temperature, nuisance alarms or unstable cycling
- Water, drain or door-seal leakage where applicable, typically indicated by leaks, poor cleaning performance or condensation
- Fan, pump or compressor wear where fitted, typically indicated by noise, reduced performance or trip alarms
- Grease/dirt accumulation or blocked filters, typically indicated by reduced airflow, overheating, odor or hygiene issues
Service: Inspect electrical safety, controls, thermostats, seals, drains, filters, fans/pumps/compressors as applicable, ventilation and cleanliness; exact operating temperatures and service limits come from manufacturer documentation.
Spare Parts: Keep door seals, heating elements or thermostats, filters, relays/contactors, pumps/fans and appliance-specific wear parts for critical galley equipment.
Use Cases: Used in ship galleys and domestic spaces on merchant, passenger, offshore and naval vessels. This entry applies specifically to the Dishwasher variant identified as Winterhalter Marine Dishwasher Medium 440V Marine.
Dishwasher Large 230V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
230
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Loss of electrical, hydraulic, pneumatic, fluid, or other service supply from a protection trip, leakage, blockage, or upstream fault results in failed starting or loss of function
- Mechanical wear, corrosion, fouling, or contamination of moving and wetted parts causes increased noise, leakage, sticking, vibration, or reduced performance
- Seal, gasket, hose, cable, or connection deterioration from age, heat, vibration, or environmental exposure produces visible leakage, intermittent signals, or loss of pressure
- Sensor, switch, actuator, relay, or control-system faults cause incorrect indication, nuisance alarms, failed automatic sequences, or loss of remote control
- Incorrect adjustment, assembly, or maintenance leads to unstable operation, recurrent alarms, or performance that differs from the vessel's normal baseline
Service: Inspect the unit for leakage, corrosion, contamination, loose connections, abnormal noise or vibration, condition of guards and mountings, service supplies, controls, alarms, and functional performance. Use maintenance history to identify deterioration trends and refer to manufacturer documentation for exact settings, tolerances, test values, and overhaul criteria.
Spare Parts: Keep the manufacturer-recommended seals and gaskets, filters where fitted, fuses or protection items, common sensors and switches, and critical actuator, control, or wear components appropriate to the installed configuration. Exact part numbers and quantities must come from the manufacturer spare-parts documentation.
Use Cases: Used on vessel types fitted with galley & domestic equipment, including merchant, offshore, passenger, fishing, or workboat installations where this specific dishwasher duty is required.
Dishwasher Large 400V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
400
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Loss of electrical, hydraulic, pneumatic, fluid, or other service supply from a protection trip, leakage, blockage, or upstream fault results in failed starting or loss of function
- Mechanical wear, corrosion, fouling, or contamination of moving and wetted parts causes increased noise, leakage, sticking, vibration, or reduced performance
- Seal, gasket, hose, cable, or connection deterioration from age, heat, vibration, or environmental exposure produces visible leakage, intermittent signals, or loss of pressure
- Sensor, switch, actuator, relay, or control-system faults cause incorrect indication, nuisance alarms, failed automatic sequences, or loss of remote control
- Incorrect adjustment, assembly, or maintenance leads to unstable operation, recurrent alarms, or performance that differs from the vessel's normal baseline
Service: Inspect the unit for leakage, corrosion, contamination, loose connections, abnormal noise or vibration, condition of guards and mountings, service supplies, controls, alarms, and functional performance. Use maintenance history to identify deterioration trends and refer to manufacturer documentation for exact settings, tolerances, test values, and overhaul criteria.
Spare Parts: Keep the manufacturer-recommended seals and gaskets, filters where fitted, fuses or protection items, common sensors and switches, and critical actuator, control, or wear components appropriate to the installed configuration. Exact part numbers and quantities must come from the manufacturer spare-parts documentation.
Use Cases: Used on vessel types fitted with galley & domestic equipment, including merchant, offshore, passenger, fishing, or workboat installations where this specific dishwasher duty is required.
Dishwasher Large 440V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
440
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Loss of electrical, hydraulic, pneumatic, fluid, or other service supply from a protection trip, leakage, blockage, or upstream fault results in failed starting or loss of function
- Mechanical wear, corrosion, fouling, or contamination of moving and wetted parts causes increased noise, leakage, sticking, vibration, or reduced performance
- Seal, gasket, hose, cable, or connection deterioration from age, heat, vibration, or environmental exposure produces visible leakage, intermittent signals, or loss of pressure
- Sensor, switch, actuator, relay, or control-system faults cause incorrect indication, nuisance alarms, failed automatic sequences, or loss of remote control
- Incorrect adjustment, assembly, or maintenance leads to unstable operation, recurrent alarms, or performance that differs from the vessel's normal baseline
Service: Inspect the unit for leakage, corrosion, contamination, loose connections, abnormal noise or vibration, condition of guards and mountings, service supplies, controls, alarms, and functional performance. Use maintenance history to identify deterioration trends and refer to manufacturer documentation for exact settings, tolerances, test values, and overhaul criteria.
Spare Parts: Keep the manufacturer-recommended seals and gaskets, filters where fitted, fuses or protection items, common sensors and switches, and critical actuator, control, or wear components appropriate to the installed configuration. Exact part numbers and quantities must come from the manufacturer spare-parts documentation.
Use Cases: Used on vessel types fitted with galley & domestic equipment, including merchant, offshore, passenger, fishing, or workboat installations where this specific dishwasher duty is required.
Dishwasher XL 230V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
230
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner or thermostat faults caused by ageing, contamination or control failure can result in slow heating, overheating or failure to reach operating condition
- Door, seal or gasket deterioration caused by heat and repeated use can cause heat loss, steam leakage or poor washing performance
- Drain, spray or filter blockage caused by food debris or scale can produce poor cleaning, standing water or overflow
- Switch, contactor or control-board faults caused by moisture or component wear can lead to intermittent operation or failure to start
- Ventilation or cooling obstruction caused by grease or dust can increase appliance temperature and cause nuisance trips or component damage
Service: Inspect cleanliness, guards, wiring, controls, seals, drains, ventilation and utility connections. Confirm safety cut-outs and protective devices operate without bypassing them, and remove grease or scale according to the maker's procedure. Refer to manufacturer documentation for exact electrical, gas, temperature and service values.
Spare Parts: Useful spares include seals, heating or control components, filters, switches, contactors, fuses, spray or drain parts and other maker-approved consumables suited to the appliance.
Use Cases: Merchant, passenger, ferry and offshore-vessel galleys and catering spaces.
Dishwasher XL 400V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
400
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner or thermostat faults caused by ageing, contamination or control failure can result in slow heating, overheating or failure to reach operating condition
- Door, seal or gasket deterioration caused by heat and repeated use can cause heat loss, steam leakage or poor washing performance
- Drain, spray or filter blockage caused by food debris or scale can produce poor cleaning, standing water or overflow
- Switch, contactor or control-board faults caused by moisture or component wear can lead to intermittent operation or failure to start
- Ventilation or cooling obstruction caused by grease or dust can increase appliance temperature and cause nuisance trips or component damage
Service: Inspect cleanliness, guards, wiring, controls, seals, drains, ventilation and utility connections. Confirm safety cut-outs and protective devices operate without bypassing them, and remove grease or scale according to the maker's procedure. Refer to manufacturer documentation for exact electrical, gas, temperature and service values.
Spare Parts: Useful spares include seals, heating or control components, filters, switches, contactors, fuses, spray or drain parts and other maker-approved consumables suited to the appliance.
Use Cases: Merchant, passenger, ferry and offshore-vessel galleys and catering spaces.
Dishwasher XL 440V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
440
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner or thermostat faults caused by ageing, contamination or control failure can result in slow heating, overheating or failure to reach operating condition
- Door, seal or gasket deterioration caused by heat and repeated use can cause heat loss, steam leakage or poor washing performance
- Drain, spray or filter blockage caused by food debris or scale can produce poor cleaning, standing water or overflow
- Switch, contactor or control-board faults caused by moisture or component wear can lead to intermittent operation or failure to start
- Ventilation or cooling obstruction caused by grease or dust can increase appliance temperature and cause nuisance trips or component damage
Service: Inspect cleanliness, guards, wiring, controls, seals, drains, ventilation and utility connections. Confirm safety cut-outs and protective devices operate without bypassing them, and remove grease or scale according to the maker's procedure. Refer to manufacturer documentation for exact electrical, gas, temperature and service values.
Spare Parts: Useful spares include seals, heating or control components, filters, switches, contactors, fuses, spray or drain parts and other maker-approved consumables suited to the appliance.
Use Cases: Merchant, passenger, ferry and offshore-vessel galleys and catering spaces.
Electrolux Professional Marine
20
EUC1 Marine electric
unverified
· 6.0 kW
Power (kW)
6
Voltage (V)
400
Capacity
6 GN 1/1
Fuel
electric
Common Failures & Inspection Points
- Heating, refrigeration or motor element failure, typically indicated by loss of temperature control, inability to operate or protective trip
- Thermostat/sensor/control fault, typically indicated by incorrect temperature, nuisance alarms or unstable cycling
- Water, drain or door-seal leakage where applicable, typically indicated by leaks, poor cleaning performance or condensation
- Fan, pump or compressor wear where fitted, typically indicated by noise, reduced performance or trip alarms
- Grease/dirt accumulation or blocked filters, typically indicated by reduced airflow, overheating, odor or hygiene issues
Service: Inspect electrical safety, controls, thermostats, seals, drains, filters, fans/pumps/compressors as applicable, ventilation and cleanliness; exact operating temperatures and service limits come from manufacturer documentation.
Spare Parts: Keep door seals, heating elements or thermostats, filters, relays/contactors, pumps/fans and appliance-specific wear parts for critical galley equipment.
Use Cases: Used in ship galleys and domestic spaces on merchant, passenger, offshore and naval vessels. This entry applies specifically to the Dishwasher variant identified as Electrolux Professional Marine EUC1 Marine electric.
EUC1 Marine gas
unverified
· 6.0 kW
Power (kW)
6
Voltage (V)
400
Capacity
6 GN 1/1
Fuel
gas
Common Failures & Inspection Points
- Heating-element, burner or thermostat faults caused by ageing, contamination or control failure can result in slow heating, overheating or failure to reach operating condition
- Door, seal or gasket deterioration caused by heat and repeated use can cause heat loss, steam leakage or poor washing performance
- Drain, spray or filter blockage caused by food debris or scale can produce poor cleaning, standing water or overflow
- Switch, contactor or control-board faults caused by moisture or component wear can lead to intermittent operation or failure to start
- Ventilation or cooling obstruction caused by grease or dust can increase appliance temperature and cause nuisance trips or component damage
Service: Inspect cleanliness, guards, wiring, controls, seals, drains, ventilation and utility connections. Confirm safety cut-outs and protective devices operate without bypassing them, and remove grease or scale according to the maker's procedure. Refer to manufacturer documentation for exact electrical, gas, temperature and service values.
Spare Parts: Useful spares include seals, heating or control components, filters, switches, contactors, fuses, spray or drain parts and other maker-approved consumables suited to the appliance.
Use Cases: Merchant, passenger, ferry and offshore-vessel galleys and catering spaces.
EUC3 Marine electric
unverified
· 6.0 kW
Power (kW)
6
Voltage (V)
400
Capacity
6 GN 1/1
Fuel
electric
Common Failures & Inspection Points
- Heating, refrigeration or motor element failure, typically indicated by loss of temperature control, inability to operate or protective trip
- Thermostat/sensor/control fault, typically indicated by incorrect temperature, nuisance alarms or unstable cycling
- Water, drain or door-seal leakage where applicable, typically indicated by leaks, poor cleaning performance or condensation
- Fan, pump or compressor wear where fitted, typically indicated by noise, reduced performance or trip alarms
- Grease/dirt accumulation or blocked filters, typically indicated by reduced airflow, overheating, odor or hygiene issues
Service: Inspect electrical safety, controls, thermostats, seals, drains, filters, fans/pumps/compressors as applicable, ventilation and cleanliness; exact operating temperatures and service limits come from manufacturer documentation.
Spare Parts: Keep door seals, heating elements or thermostats, filters, relays/contactors, pumps/fans and appliance-specific wear parts for critical galley equipment.
Use Cases: Used in ship galleys and domestic spaces on merchant, passenger, offshore and naval vessels. This entry applies specifically to the Dishwasher variant identified as Electrolux Professional Marine EUC3 Marine electric.
EUC3 Marine gas
unverified
· 6.0 kW
Power (kW)
6
Voltage (V)
400
Capacity
6 GN 1/1
Fuel
gas
Common Failures & Inspection Points
- Heating-element, burner or thermostat faults caused by ageing, contamination or control failure can result in slow heating, overheating or failure to reach operating condition
- Door, seal or gasket deterioration caused by heat and repeated use can cause heat loss, steam leakage or poor washing performance
- Drain, spray or filter blockage caused by food debris or scale can produce poor cleaning, standing water or overflow
- Switch, contactor or control-board faults caused by moisture or component wear can lead to intermittent operation or failure to start
- Ventilation or cooling obstruction caused by grease or dust can increase appliance temperature and cause nuisance trips or component damage
Service: Inspect cleanliness, guards, wiring, controls, seals, drains, ventilation and utility connections. Confirm safety cut-outs and protective devices operate without bypassing them, and remove grease or scale according to the maker's procedure. Refer to manufacturer documentation for exact electrical, gas, temperature and service values.
Spare Parts: Useful spares include seals, heating or control components, filters, switches, contactors, fuses, spray or drain parts and other maker-approved consumables suited to the appliance.
Use Cases: Merchant, passenger, ferry and offshore-vessel galleys and catering spaces.
EHT8 Marine electric
unverified
· 6.0 kW
Power (kW)
6
Voltage (V)
400
Capacity
6 GN 1/1
Fuel
electric
Common Failures & Inspection Points
- Heating, refrigeration or motor element failure, typically indicated by loss of temperature control, inability to operate or protective trip
- Thermostat/sensor/control fault, typically indicated by incorrect temperature, nuisance alarms or unstable cycling
- Water, drain or door-seal leakage where applicable, typically indicated by leaks, poor cleaning performance or condensation
- Fan, pump or compressor wear where fitted, typically indicated by noise, reduced performance or trip alarms
- Grease/dirt accumulation or blocked filters, typically indicated by reduced airflow, overheating, odor or hygiene issues
Service: Inspect electrical safety, controls, thermostats, seals, drains, filters, fans/pumps/compressors as applicable, ventilation and cleanliness; exact operating temperatures and service limits come from manufacturer documentation.
Spare Parts: Keep door seals, heating elements or thermostats, filters, relays/contactors, pumps/fans and appliance-specific wear parts for critical galley equipment.
Use Cases: Used in ship galleys and domestic spaces on merchant, passenger, offshore and naval vessels. This entry applies specifically to the Dishwasher variant identified as Electrolux Professional Marine EHT8 Marine electric.
EHT8 Marine gas
unverified
· 6.0 kW
Power (kW)
6
Voltage (V)
400
Capacity
6 GN 1/1
Fuel
gas
Common Failures & Inspection Points
- Heating-element, burner or thermostat faults caused by ageing, contamination or control failure can result in slow heating, overheating or failure to reach operating condition
- Door, seal or gasket deterioration caused by heat and repeated use can cause heat loss, steam leakage or poor washing performance
- Drain, spray or filter blockage caused by food debris or scale can produce poor cleaning, standing water or overflow
- Switch, contactor or control-board faults caused by moisture or component wear can lead to intermittent operation or failure to start
- Ventilation or cooling obstruction caused by grease or dust can increase appliance temperature and cause nuisance trips or component damage
Service: Inspect cleanliness, guards, wiring, controls, seals, drains, ventilation and utility connections. Confirm safety cut-outs and protective devices operate without bypassing them, and remove grease or scale according to the maker's procedure. Refer to manufacturer documentation for exact electrical, gas, temperature and service values.
Spare Parts: Useful spares include seals, heating or control components, filters, switches, contactors, fuses, spray or drain parts and other maker-approved consumables suited to the appliance.
Use Cases: Merchant, passenger, ferry and offshore-vessel galleys and catering spaces.
EHT8IL Marine electric
unverified
· 6.0 kW
Power (kW)
6
Voltage (V)
400
Capacity
6 GN 1/1
Fuel
electric
Common Failures & Inspection Points
- Heating, refrigeration or extraction-component failure causes poor performance, slow operation or inability to reach the required condition
- Temperature sensor, thermostat or control faults cause unstable operation or protective shutdown
- Door seal, hose, drain or valve deterioration causes leakage, heat loss, icing or water accumulation
- Fan, pump, motor or bearing wear causes abnormal noise, reduced circulation or vibration
- Electrical, ignition or safety-interlock faults cause failed starts, nuisance trips or error indications
Service: Inspect seals, controls, heaters or refrigeration components, pumps or fans, water and drain connections, extraction and secure mounting according to the appliance type. Clean grease, scale, ice or food residues from approved areas. Verify safety interlocks and look for heat-damaged wiring, leaks or poor ventilation. Refer to the manufacturer documentation for the exact figure for temperature, loading and service criteria.
Spare Parts: Carry seals, sensors, fuses, control relays, pump or fan parts, heating or ignition components and appliance-specific consumables.
Use Cases: Galley, pantry, food storage and domestic service on merchant, passenger and offshore vessels.
EHT8IL Marine gas
unverified
· 6.0 kW
Power (kW)
6
Voltage (V)
400
Capacity
6 GN 1/1
Fuel
gas
Common Failures & Inspection Points
- Loss of electrical, hydraulic, pneumatic, fluid, or other service supply from a protection trip, leakage, blockage, or upstream fault results in failed starting or loss of function
- Mechanical wear, corrosion, fouling, or contamination of moving and wetted parts causes increased noise, leakage, sticking, vibration, or reduced performance
- Seal, gasket, hose, cable, or connection deterioration from age, heat, vibration, or environmental exposure produces visible leakage, intermittent signals, or loss of pressure
- Sensor, switch, actuator, relay, or control-system faults cause incorrect indication, nuisance alarms, failed automatic sequences, or loss of remote control
- Incorrect adjustment, assembly, or maintenance leads to unstable operation, recurrent alarms, or performance that differs from the vessel's normal baseline
Service: Inspect the unit for leakage, corrosion, contamination, loose connections, abnormal noise or vibration, condition of guards and mountings, service supplies, controls, alarms, and functional performance. Use maintenance history to identify deterioration trends and refer to manufacturer documentation for exact settings, tolerances, test values, and overhaul criteria.
Spare Parts: Keep the manufacturer-recommended seals and gaskets, filters where fitted, fuses or protection items, common sensors and switches, and critical actuator, control, or wear components appropriate to the installed configuration. Exact part numbers and quantities must come from the manufacturer spare-parts documentation.
Use Cases: Used on vessel types fitted with galley & domestic equipment, including merchant, offshore, passenger, fishing, or workboat installations where this specific dishwasher duty is required.
Dishwasher Small 230V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
230
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating, refrigeration, wash-pump, fan or drive failure caused by component wear, blockage or electrical faults, resulting in poor performance or an incomplete cycle
- Temperature or control-sensor malfunction caused by drift, contamination or electrical failure, resulting in unstable operation or incorrect temperature
- Electrical terminal or contact deterioration caused by heat, moisture or loose connections, resulting in intermittent operation, overheating or breaker trips
- Door, lid, seal, roller or guard deterioration caused by repeated use, resulting in leakage, heat loss, poor finishing or unsafe access
- Drain, filter or ventilation restriction caused by food, lint or grease deposits, resulting in poor performance, odor, water leakage or overheating
Service: Keep working surfaces, filters, drains and ventilation openings clean as applicable to the appliance. Inspect electrical terminals, controls, doors, guards and safety interlocks for heat damage or looseness. Verify temperature or cycle control using the vessel's approved maintenance method and investigate repeated trips before resetting. Check secure fastening to the ship structure and inspect flexible service connections where fitted. Use cleaning chemicals compatible with stainless steel, seals and electrical components. Refer to the manufacturer documentation for the exact figure for electrical ratings, calibration and service settings.
Spare Parts: Keep door or lid seals, temperature sensors, thermostats, heating elements, pumps, fans, belts or refrigeration components as applicable, together with fuses, switches and manufacturer-recommended control parts.
Use Cases: It is used for galley and catering service on merchant ships, passenger vessels, offshore units or other vessel types where this equipment category is fitted.
Dishwasher Small 400V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
400
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating, refrigeration, wash-pump, fan or drive failure caused by component wear, blockage or electrical faults, resulting in poor performance or an incomplete cycle
- Temperature or control-sensor malfunction caused by drift, contamination or electrical failure, resulting in unstable operation or incorrect temperature
- Electrical terminal or contact deterioration caused by heat, moisture or loose connections, resulting in intermittent operation, overheating or breaker trips
- Door, lid, seal, roller or guard deterioration caused by repeated use, resulting in leakage, heat loss, poor finishing or unsafe access
- Drain, filter or ventilation restriction caused by food, lint or grease deposits, resulting in poor performance, odor, water leakage or overheating
Service: Keep working surfaces, filters, drains and ventilation openings clean as applicable to the appliance. Inspect electrical terminals, controls, doors, guards and safety interlocks for heat damage or looseness. Verify temperature or cycle control using the vessel's approved maintenance method and investigate repeated trips before resetting. Check secure fastening to the ship structure and inspect flexible service connections where fitted. Use cleaning chemicals compatible with stainless steel, seals and electrical components. Refer to the manufacturer documentation for the exact figure for electrical ratings, calibration and service settings.
Spare Parts: Keep door or lid seals, temperature sensors, thermostats, heating elements, pumps, fans, belts or refrigeration components as applicable, together with fuses, switches and manufacturer-recommended control parts.
Use Cases: It is used for galley and catering service on merchant ships, passenger vessels, offshore units or other vessel types where this equipment category is fitted.
Dishwasher Small 440V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
440
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating, refrigeration, wash-pump, fan or drive failure caused by component wear, blockage or electrical faults, resulting in poor performance or an incomplete cycle
- Temperature or control-sensor malfunction caused by drift, contamination or electrical failure, resulting in unstable operation or incorrect temperature
- Electrical terminal or contact deterioration caused by heat, moisture or loose connections, resulting in intermittent operation, overheating or breaker trips
- Door, lid, seal, roller or guard deterioration caused by repeated use, resulting in leakage, heat loss, poor finishing or unsafe access
- Drain, filter or ventilation restriction caused by food, lint or grease deposits, resulting in poor performance, odor, water leakage or overheating
Service: Keep working surfaces, filters, drains and ventilation openings clean as applicable to the appliance. Inspect electrical terminals, controls, doors, guards and safety interlocks for heat damage or looseness. Verify temperature or cycle control using the vessel's approved maintenance method and investigate repeated trips before resetting. Check secure fastening to the ship structure and inspect flexible service connections where fitted. Use cleaning chemicals compatible with stainless steel, seals and electrical components. Refer to the manufacturer documentation for the exact figure for electrical ratings, calibration and service settings.
Spare Parts: Keep door or lid seals, temperature sensors, thermostats, heating elements, pumps, fans, belts or refrigeration components as applicable, together with fuses, switches and manufacturer-recommended control parts.
Use Cases: It is used for galley and catering service on merchant ships, passenger vessels, offshore units or other vessel types where this equipment category is fitted.
Dishwasher Medium 230V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
230
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating, refrigeration, wash-pump, fan or drive failure caused by component wear, blockage or electrical faults, resulting in poor performance or an incomplete cycle
- Temperature or control-sensor malfunction caused by drift, contamination or electrical failure, resulting in unstable operation or incorrect temperature
- Electrical terminal or contact deterioration caused by heat, moisture or loose connections, resulting in intermittent operation, overheating or breaker trips
- Door, lid, seal, roller or guard deterioration caused by repeated use, resulting in leakage, heat loss, poor finishing or unsafe access
- Drain, filter or ventilation restriction caused by food, lint or grease deposits, resulting in poor performance, odor, water leakage or overheating
Service: Keep working surfaces, filters, drains and ventilation openings clean as applicable to the appliance. Inspect electrical terminals, controls, doors, guards and safety interlocks for heat damage or looseness. Verify temperature or cycle control using the vessel's approved maintenance method and investigate repeated trips before resetting. Check secure fastening to the ship structure and inspect flexible service connections where fitted. Use cleaning chemicals compatible with stainless steel, seals and electrical components. Refer to the manufacturer documentation for the exact figure for electrical ratings, calibration and service settings.
Spare Parts: Keep door or lid seals, temperature sensors, thermostats, heating elements, pumps, fans, belts or refrigeration components as applicable, together with fuses, switches and manufacturer-recommended control parts.
Use Cases: It is used for galley and catering service on merchant ships, passenger vessels, offshore units or other vessel types where this equipment category is fitted.
Dishwasher Medium 400V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
400
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating, refrigeration, wash-pump, fan or drive failure caused by component wear, blockage or electrical faults, resulting in poor performance or an incomplete cycle
- Temperature or control-sensor malfunction caused by drift, contamination or electrical failure, resulting in unstable operation or incorrect temperature
- Electrical terminal or contact deterioration caused by heat, moisture or loose connections, resulting in intermittent operation, overheating or breaker trips
- Door, lid, seal, roller or guard deterioration caused by repeated use, resulting in leakage, heat loss, poor finishing or unsafe access
- Drain, filter or ventilation restriction caused by food, lint or grease deposits, resulting in poor performance, odor, water leakage or overheating
Service: Keep working surfaces, filters, drains and ventilation openings clean as applicable to the appliance. Inspect electrical terminals, controls, doors, guards and safety interlocks for heat damage or looseness. Verify temperature or cycle control using the vessel's approved maintenance method and investigate repeated trips before resetting. Check secure fastening to the ship structure and inspect flexible service connections where fitted. Use cleaning chemicals compatible with stainless steel, seals and electrical components. Refer to the manufacturer documentation for the exact figure for electrical ratings, calibration and service settings.
Spare Parts: Keep door or lid seals, temperature sensors, thermostats, heating elements, pumps, fans, belts or refrigeration components as applicable, together with fuses, switches and manufacturer-recommended control parts.
Use Cases: It is used for galley and catering service on merchant ships, passenger vessels, offshore units or other vessel types where this equipment category is fitted.
Dishwasher Medium 440V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
440
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating, refrigeration, wash-pump, fan or drive failure caused by component wear, blockage or electrical faults, resulting in poor performance or an incomplete cycle
- Temperature or control-sensor malfunction caused by drift, contamination or electrical failure, resulting in unstable operation or incorrect temperature
- Electrical terminal or contact deterioration caused by heat, moisture or loose connections, resulting in intermittent operation, overheating or breaker trips
- Door, lid, seal, roller or guard deterioration caused by repeated use, resulting in leakage, heat loss, poor finishing or unsafe access
- Drain, filter or ventilation restriction caused by food, lint or grease deposits, resulting in poor performance, odor, water leakage or overheating
Service: Keep working surfaces, filters, drains and ventilation openings clean as applicable to the appliance. Inspect electrical terminals, controls, doors, guards and safety interlocks for heat damage or looseness. Verify temperature or cycle control using the vessel's approved maintenance method and investigate repeated trips before resetting. Check secure fastening to the ship structure and inspect flexible service connections where fitted. Use cleaning chemicals compatible with stainless steel, seals and electrical components. Refer to the manufacturer documentation for the exact figure for electrical ratings, calibration and service settings.
Spare Parts: Keep door or lid seals, temperature sensors, thermostats, heating elements, pumps, fans, belts or refrigeration components as applicable, together with fuses, switches and manufacturer-recommended control parts.
Use Cases: It is used for galley and catering service on merchant ships, passenger vessels, offshore units or other vessel types where this equipment category is fitted.
Dishwasher Large 230V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
230
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, thermostat or temperature-sensing failure, noticed as poor wash/rinse performance or incomplete cycles
- Wash/rinse pump or seal deterioration, noticed as weak spray pressure, noise or leakage
- Blocked spray nozzles and filters from food debris or scale, noticed as poor cleaning results
- Door gasket or latch wear, noticed as water leakage during operation
- Drain restriction or pump blockage, noticed as standing water or cycle alarms
- Control or electrical faults promoted by humidity or power disturbance, noticed as intermittent operation or failure to start
Service: Clean strainers, spray arms and accessible wash chamber surfaces routinely and control scale according to the vessel water condition and maker guidance. Inspect door seals, pumps, hoses, electrical connections and drainage for leakage or deterioration. Verify heating and temperature indication operate correctly and that electrical protection and earthing remain intact. Secure the appliance and connected services against shipboard vibration. Use manufacturer documentation for exact cleaning chemicals, temperatures, test procedures and service intervals; class attention is normally limited to safe electrical installation unless the appliance is part of a wider approved galley arrangement.
Spare Parts: Keep door seals, pump seals where serviceable, common filters/strainers, spray-arm components, fuses and frequently failing sensors or switches appropriate to the exact model. A critical heating element, thermostat or drain-pump component may be sensible on vessels with long supply routes. Confirm voltage and part revision from the appliance serial data.
Use Cases: Used in galleys and pantries on passenger ships, ferries, cruise vessels, offshore units and merchant ships with commercial-scale catering requirements.
Dishwasher Large 400V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
400
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating, refrigeration, wash-pump, fan or drive failure caused by component wear, blockage or electrical faults, resulting in poor performance or an incomplete cycle
- Temperature or control-sensor malfunction caused by drift, contamination or electrical failure, resulting in unstable operation or incorrect temperature
- Electrical terminal or contact deterioration caused by heat, moisture or loose connections, resulting in intermittent operation, overheating or breaker trips
- Door, lid, seal, roller or guard deterioration caused by repeated use, resulting in leakage, heat loss, poor finishing or unsafe access
- Drain, filter or ventilation restriction caused by food, lint or grease deposits, resulting in poor performance, odor, water leakage or overheating
Service: Keep working surfaces, filters, drains and ventilation openings clean as applicable to the appliance. Inspect electrical terminals, controls, doors, guards and safety interlocks for heat damage or looseness. Verify temperature or cycle control using the vessel's approved maintenance method and investigate repeated trips before resetting. Check secure fastening to the ship structure and inspect flexible service connections where fitted. Use cleaning chemicals compatible with stainless steel, seals and electrical components. Refer to the manufacturer documentation for the exact figure for electrical ratings, calibration and service settings.
Spare Parts: Keep door or lid seals, temperature sensors, thermostats, heating elements, pumps, fans, belts or refrigeration components as applicable, together with fuses, switches and manufacturer-recommended control parts.
Use Cases: It is used for galley and catering service on merchant ships, passenger vessels, offshore units or other vessel types where this equipment category is fitted.
Dishwasher Large 440V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
440
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating, refrigeration, wash-pump, fan or drive failure caused by component wear, blockage or electrical faults, resulting in poor performance or an incomplete cycle
- Temperature or control-sensor malfunction caused by drift, contamination or electrical failure, resulting in unstable operation or incorrect temperature
- Electrical terminal or contact deterioration caused by heat, moisture or loose connections, resulting in intermittent operation, overheating or breaker trips
- Door, lid, seal, roller or guard deterioration caused by repeated use, resulting in leakage, heat loss, poor finishing or unsafe access
- Drain, filter or ventilation restriction caused by food, lint or grease deposits, resulting in poor performance, odor, water leakage or overheating
Service: Keep working surfaces, filters, drains and ventilation openings clean as applicable to the appliance. Inspect electrical terminals, controls, doors, guards and safety interlocks for heat damage or looseness. Verify temperature or cycle control using the vessel's approved maintenance method and investigate repeated trips before resetting. Check secure fastening to the ship structure and inspect flexible service connections where fitted. Use cleaning chemicals compatible with stainless steel, seals and electrical components. Refer to the manufacturer documentation for the exact figure for electrical ratings, calibration and service settings.
Spare Parts: Keep door or lid seals, temperature sensors, thermostats, heating elements, pumps, fans, belts or refrigeration components as applicable, together with fuses, switches and manufacturer-recommended control parts.
Use Cases: It is used for galley and catering service on merchant ships, passenger vessels, offshore units or other vessel types where this equipment category is fitted.
Dishwasher XL 230V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
230
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating, refrigeration, fan, pump or drive component failure caused by wear, blockage or electrical faults, resulting in poor appliance performance or an incomplete cycle
- Temperature or control-sensor malfunction caused by drift, contamination or electrical failure, resulting in unstable operation or incorrect temperature
- Electrical terminal or contact deterioration caused by heat, moisture or loose connections, resulting in intermittent operation, overheating or breaker trips
- Door, lid, seal or guard deterioration caused by repeated use, resulting in leakage, heat loss, cold loss or unsafe access
- Drain, filter or ventilation restriction caused by food residue or grease, resulting in poor performance, odor, water leakage or overheating
Service: Keep cooking, cooling or wash surfaces, filters, drains and ventilation openings clean as applicable to the appliance. Inspect electrical terminals, controls, doors, guards and safety interlocks for heat damage or looseness. Verify temperature or cycle control using the vessel's approved maintenance method and investigate repeated trips before resetting. Check secure fastening to the galley structure and inspect flexible service connections where fitted. Use cleaning chemicals compatible with stainless steel, seals and electrical components. Refer to the manufacturer documentation for the exact figure for electrical ratings, calibration and service settings.
Spare Parts: Keep door or lid seals, temperature sensors, thermostats, selected heating elements, pumps, fans or refrigeration components where applicable, fuses, switches and manufacturer-recommended control parts. High-use passenger vessels may justify additional wear components. Verify all electrical and mechanical parts against the appliance nameplate.
Use Cases: Food preparation, cleaning, extraction, holding and cold storage in merchant-ship, ferry, cruise-ship and offshore galley installations.
Dishwasher XL 400V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
400
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating, refrigeration, fan, pump or drive component failure caused by wear, blockage or electrical faults, resulting in poor appliance performance or an incomplete cycle
- Temperature or control-sensor malfunction caused by drift, contamination or electrical failure, resulting in unstable operation or incorrect temperature
- Electrical terminal or contact deterioration caused by heat, moisture or loose connections, resulting in intermittent operation, overheating or breaker trips
- Door, lid, seal or guard deterioration caused by repeated use, resulting in leakage, heat loss, cold loss or unsafe access
- Drain, filter or ventilation restriction caused by food residue or grease, resulting in poor performance, odor, water leakage or overheating
Service: Keep cooking, cooling or wash surfaces, filters, drains and ventilation openings clean as applicable to the appliance. Inspect electrical terminals, controls, doors, guards and safety interlocks for heat damage or looseness. Verify temperature or cycle control using the vessel's approved maintenance method and investigate repeated trips before resetting. Check secure fastening to the galley structure and inspect flexible service connections where fitted. Use cleaning chemicals compatible with stainless steel, seals and electrical components. Refer to the manufacturer documentation for the exact figure for electrical ratings, calibration and service settings.
Spare Parts: Keep door or lid seals, temperature sensors, thermostats, selected heating elements, pumps, fans or refrigeration components where applicable, fuses, switches and manufacturer-recommended control parts. High-use passenger vessels may justify additional wear components. Verify all electrical and mechanical parts against the appliance nameplate.
Use Cases: Food preparation, cleaning, extraction, holding and cold storage in merchant-ship, ferry, cruise-ship and offshore galley installations.
Dishwasher XL 440V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
440
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating, refrigeration, fan, pump or drive component failure caused by wear, blockage or electrical faults, resulting in poor appliance performance or an incomplete cycle
- Temperature or control-sensor malfunction caused by drift, contamination or electrical failure, resulting in unstable operation or incorrect temperature
- Electrical terminal or contact deterioration caused by heat, moisture or loose connections, resulting in intermittent operation, overheating or breaker trips
- Door, lid, seal or guard deterioration caused by repeated use, resulting in leakage, heat loss, cold loss or unsafe access
- Drain, filter or ventilation restriction caused by food residue or grease, resulting in poor performance, odor, water leakage or overheating
Service: Keep cooking, cooling or wash surfaces, filters, drains and ventilation openings clean as applicable to the appliance. Inspect electrical terminals, controls, doors, guards and safety interlocks for heat damage or looseness. Verify temperature or cycle control using the vessel's approved maintenance method and investigate repeated trips before resetting. Check secure fastening to the galley structure and inspect flexible service connections where fitted. Use cleaning chemicals compatible with stainless steel, seals and electrical components. Refer to the manufacturer documentation for the exact figure for electrical ratings, calibration and service settings.
Spare Parts: Keep door or lid seals, temperature sensors, thermostats, selected heating elements, pumps, fans or refrigeration components where applicable, fuses, switches and manufacturer-recommended control parts. High-use passenger vessels may justify additional wear components. Verify all electrical and mechanical parts against the appliance nameplate.
Use Cases: Food preparation, cleaning, extraction, holding and cold storage in merchant-ship, ferry, cruise-ship and offshore galley installations.
Metos Marine
16
WD-6 Marine electric
unverified
· 6.0 kW
Power (kW)
6
Voltage (V)
400
Capacity
6 GN 1/1
Fuel
electric
Common Failures & Inspection Points
- Spray-arm or nozzle blockage reduces washing performance and leaves food or detergent residue
- Heating-element or thermostat failure causes poor wash or rinse temperature and cycle alarms
- Pump wear or seal leakage causes weak circulation, abnormal noise or water leakage
- Door-switch or safety-interlock failure prevents a cycle from starting or causes nuisance stoppage
- Scale, detergent buildup or drain blockage causes poor rinsing, slow draining or flooding
Service: Inspect spray arms, filters, pumps, heaters, door seals, safety switches, dosing equipment and drains. Remove scale using approved methods and verify secure electrical and water connections. Check for leaks and overheating at terminals. Refer to manufacturer documentation for exact detergent, temperature and service settings.
Spare Parts: Carry pump seals, door seals, spray nozzles, heater or thermostat parts, drain-valve components, filters, fuses and control relays.
Use Cases: Commercial ship galleys, passenger-service areas and offshore accommodation facilities.
WD-6 Marine gas
unverified
· 6.0 kW
Power (kW)
6
Voltage (V)
400
Capacity
6 GN 1/1
Fuel
gas
Common Failures & Inspection Points
- Heating or wash-process failure caused by heater, burner, pump or control faults, noticed as poor temperature rise or incomplete cycles
- Water/steam/drain fault caused by scale, blocked filters, valves or pumps, noticed as alarms, leakage or standing water
- Door seal or interlock failure caused by wear, noticed as leakage or inability to start safely
- Fan/spray/dosing failure caused by motor, nozzle or chemical-feed faults, noticed as uneven cooking or poor cleaning results
- Temperature sensor or controller failure caused by probe/electronics faults, noticed as unstable operation or error codes
Service: Inspect heating source, water system, drains, filters, pumps/fans, door seals and interlocks, dosing or steam systems where fitted, and secure marine mounting. Verify ventilation and safe electrical/gas isolation. Descale and clean only using manufacturer-approved methods.
Spare Parts: Carry door seals, fuses, temperature sensors, water filters, pump/fan service parts, spray/dosing components and manufacturer-approved burner/ignition parts for gas versions. Maintain specified cleaning and treatment consumables.
Use Cases: Used in merchant and passenger-ship galleys for high-volume cooking, steaming or washing of crockery and utensils.
WD-7 Marine electric
unverified
· 6.0 kW
Power (kW)
6
Voltage (V)
400
Capacity
6 GN 1/1
Fuel
electric
Common Failures & Inspection Points
- Spray-arm or nozzle blockage reduces washing performance and leaves food or detergent residue
- Heating-element or thermostat failure causes poor wash or rinse temperature and cycle alarms
- Pump wear or seal leakage causes weak circulation, abnormal noise or water leakage
- Door-switch or safety-interlock failure prevents a cycle from starting or causes nuisance stoppage
- Scale, detergent buildup or drain blockage causes poor rinsing, slow draining or flooding
Service: Inspect spray arms, filters, pumps, heaters, door seals, safety switches, dosing equipment and drains. Remove scale using approved methods and verify secure electrical and water connections. Check for leaks and overheating at terminals. Refer to manufacturer documentation for exact detergent, temperature and service settings.
Spare Parts: Carry pump seals, door seals, spray nozzles, heater or thermostat parts, drain-valve components, filters, fuses and control relays.
Use Cases: Commercial ship galleys, passenger-service areas and offshore accommodation facilities.
WD-7 Marine gas
unverified
· 6.0 kW
Power (kW)
6
Voltage (V)
400
Capacity
6 GN 1/1
Fuel
gas
Common Failures & Inspection Points
- Heating or wash-process failure caused by heater, burner, pump or control faults, noticed as poor temperature rise or incomplete cycles
- Water/steam/drain fault caused by scale, blocked filters, valves or pumps, noticed as alarms, leakage or standing water
- Door seal or interlock failure caused by wear, noticed as leakage or inability to start safely
- Fan/spray/dosing failure caused by motor, nozzle or chemical-feed faults, noticed as uneven cooking or poor cleaning results
- Temperature sensor or controller failure caused by probe/electronics faults, noticed as unstable operation or error codes
Service: Inspect heating source, water system, drains, filters, pumps/fans, door seals and interlocks, dosing or steam systems where fitted, and secure marine mounting. Verify ventilation and safe electrical/gas isolation. Descale and clean only using manufacturer-approved methods.
Spare Parts: Carry door seals, fuses, temperature sensors, water filters, pump/fan service parts, spray/dosing components and manufacturer-approved burner/ignition parts for gas versions. Maintain specified cleaning and treatment consumables.
Use Cases: Used in merchant and passenger-ship galleys for high-volume cooking, steaming or washing of crockery and utensils.
Dishwasher Small 230V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
230
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher Small 400V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
400
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher Small 440V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
440
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher Medium 230V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
230
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher Medium 400V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
400
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher Medium 440V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
440
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher Large 230V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
230
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher Large 400V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
400
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher Large 440V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
440
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher XL 230V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
230
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher XL 400V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
400
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher XL 440V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
440
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Franke Marine
12
Dishwasher Small 230V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
230
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher Small 400V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
400
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher Small 440V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
440
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher Medium 230V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
230
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner or thermostat faults caused by ageing, contamination or control failure can result in slow heating, overheating or failure to reach operating condition
- Door, seal or gasket deterioration caused by heat and repeated use can cause heat loss, steam leakage or poor washing performance
- Drain, spray or filter blockage caused by food debris or scale can produce poor cleaning, standing water or overflow
- Switch, contactor or control-board faults caused by moisture or component wear can lead to intermittent operation or failure to start
- Ventilation or cooling obstruction caused by grease or dust can increase appliance temperature and cause nuisance trips or component damage
Service: Inspect cleanliness, guards, wiring, controls, seals, drains, ventilation and utility connections. Confirm safety cut-outs and protective devices operate without bypassing them, and remove grease or scale according to the maker's procedure. Refer to manufacturer documentation for exact electrical, gas, temperature and service values.
Spare Parts: Useful spares include seals, heating or control components, filters, switches, contactors, fuses, spray or drain parts and other maker-approved consumables suited to the appliance.
Use Cases: Merchant, passenger, ferry and offshore-vessel galleys and catering spaces.
Dishwasher Medium 400V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
400
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner or thermostat faults caused by ageing, contamination or control failure can result in slow heating, overheating or failure to reach operating condition
- Door, seal or gasket deterioration caused by heat and repeated use can cause heat loss, steam leakage or poor washing performance
- Drain, spray or filter blockage caused by food debris or scale can produce poor cleaning, standing water or overflow
- Switch, contactor or control-board faults caused by moisture or component wear can lead to intermittent operation or failure to start
- Ventilation or cooling obstruction caused by grease or dust can increase appliance temperature and cause nuisance trips or component damage
Service: Inspect cleanliness, guards, wiring, controls, seals, drains, ventilation and utility connections. Confirm safety cut-outs and protective devices operate without bypassing them, and remove grease or scale according to the maker's procedure. Refer to manufacturer documentation for exact electrical, gas, temperature and service values.
Spare Parts: Useful spares include seals, heating or control components, filters, switches, contactors, fuses, spray or drain parts and other maker-approved consumables suited to the appliance.
Use Cases: Merchant, passenger, ferry and offshore-vessel galleys and catering spaces.
Dishwasher Medium 440V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
440
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner or thermostat faults caused by ageing, contamination or control failure can result in slow heating, overheating or failure to reach operating condition
- Door, seal or gasket deterioration caused by heat and repeated use can cause heat loss, steam leakage or poor washing performance
- Drain, spray or filter blockage caused by food debris or scale can produce poor cleaning, standing water or overflow
- Switch, contactor or control-board faults caused by moisture or component wear can lead to intermittent operation or failure to start
- Ventilation or cooling obstruction caused by grease or dust can increase appliance temperature and cause nuisance trips or component damage
Service: Inspect cleanliness, guards, wiring, controls, seals, drains, ventilation and utility connections. Confirm safety cut-outs and protective devices operate without bypassing them, and remove grease or scale according to the maker's procedure. Refer to manufacturer documentation for exact electrical, gas, temperature and service values.
Spare Parts: Useful spares include seals, heating or control components, filters, switches, contactors, fuses, spray or drain parts and other maker-approved consumables suited to the appliance.
Use Cases: Merchant, passenger, ferry and offshore-vessel galleys and catering spaces.
Dishwasher Large 230V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
230
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher Large 400V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
400
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher Large 440V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
440
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher XL 230V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
230
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher XL 400V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
400
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher XL 440V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
440
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Hupfer Marine
12
Dishwasher Small 230V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
230
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher Small 400V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
400
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher Small 440V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
440
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher Medium 230V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
230
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner or thermostat faults caused by ageing, contamination or control failure can result in slow heating, overheating or failure to reach operating condition
- Door, seal or gasket deterioration caused by heat and repeated use can cause heat loss, steam leakage or poor washing performance
- Drain, spray or filter blockage caused by food debris or scale can produce poor cleaning, standing water or overflow
- Switch, contactor or control-board faults caused by moisture or component wear can lead to intermittent operation or failure to start
- Ventilation or cooling obstruction caused by grease or dust can increase appliance temperature and cause nuisance trips or component damage
Service: Inspect cleanliness, guards, wiring, controls, seals, drains, ventilation and utility connections. Confirm safety cut-outs and protective devices operate without bypassing them, and remove grease or scale according to the maker's procedure. Refer to manufacturer documentation for exact electrical, gas, temperature and service values.
Spare Parts: Useful spares include seals, heating or control components, filters, switches, contactors, fuses, spray or drain parts and other maker-approved consumables suited to the appliance.
Use Cases: Merchant, passenger, ferry and offshore-vessel galleys and catering spaces.
Dishwasher Medium 400V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
400
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner or thermostat faults caused by ageing, contamination or control failure can result in slow heating, overheating or failure to reach operating condition
- Door, seal or gasket deterioration caused by heat and repeated use can cause heat loss, steam leakage or poor washing performance
- Drain, spray or filter blockage caused by food debris or scale can produce poor cleaning, standing water or overflow
- Switch, contactor or control-board faults caused by moisture or component wear can lead to intermittent operation or failure to start
- Ventilation or cooling obstruction caused by grease or dust can increase appliance temperature and cause nuisance trips or component damage
Service: Inspect cleanliness, guards, wiring, controls, seals, drains, ventilation and utility connections. Confirm safety cut-outs and protective devices operate without bypassing them, and remove grease or scale according to the maker's procedure. Refer to manufacturer documentation for exact electrical, gas, temperature and service values.
Spare Parts: Useful spares include seals, heating or control components, filters, switches, contactors, fuses, spray or drain parts and other maker-approved consumables suited to the appliance.
Use Cases: Merchant, passenger, ferry and offshore-vessel galleys and catering spaces.
Dishwasher Medium 440V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
440
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner or thermostat faults caused by ageing, contamination or control failure can result in slow heating, overheating or failure to reach operating condition
- Door, seal or gasket deterioration caused by heat and repeated use can cause heat loss, steam leakage or poor washing performance
- Drain, spray or filter blockage caused by food debris or scale can produce poor cleaning, standing water or overflow
- Switch, contactor or control-board faults caused by moisture or component wear can lead to intermittent operation or failure to start
- Ventilation or cooling obstruction caused by grease or dust can increase appliance temperature and cause nuisance trips or component damage
Service: Inspect cleanliness, guards, wiring, controls, seals, drains, ventilation and utility connections. Confirm safety cut-outs and protective devices operate without bypassing them, and remove grease or scale according to the maker's procedure. Refer to manufacturer documentation for exact electrical, gas, temperature and service values.
Spare Parts: Useful spares include seals, heating or control components, filters, switches, contactors, fuses, spray or drain parts and other maker-approved consumables suited to the appliance.
Use Cases: Merchant, passenger, ferry and offshore-vessel galleys and catering spaces.
Dishwasher Large 230V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
230
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher Large 400V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
400
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher Large 440V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
440
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher XL 230V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
230
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher XL 400V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
400
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher XL 440V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
440
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
MKN Marine
12
Dishwasher Small 230V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
230
Capacity
standard
Fuel
electric
Dishwasher Small 400V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
400
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher Small 440V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
440
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher Medium 230V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
230
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher Medium 400V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
400
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher Medium 440V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
440
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher Large 230V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
230
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher Large 400V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
400
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher Large 440V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
440
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher XL 230V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
230
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating or drive component failure caused by wear, overheating or electrical faults, resulting in slow operation, no heat or inability to complete the normal cycle
- Temperature, level or control-sensor malfunction caused by drift or component failure, resulting in unstable operation, alarms or incorrect temperature
- Door, lid, seal or duct deterioration caused by repeated use and heat, resulting in leakage, heat loss or poor extraction
- Electrical-control fault caused by moisture, loose terminals or failed relays, resulting in intermittent operation or breaker trips
- Drain, filter, grease path or ventilation restriction where applicable caused by food deposits or poor cleaning, resulting in leakage, odor, overheating or reduced performance
Service: Keep heating surfaces, filters, drains, grease paths and ventilation openings clean as applicable to the appliance. Inspect electrical terminals, controls, doors, guards and safety interlocks for heat damage or looseness. Verify temperature or cycle control using the vessel's approved maintenance method and investigate repeated overheating or breaker trips. Check secure fastening to the galley structure and inspect flexible service connections where fitted. Use cleaning chemicals compatible with stainless steel, seals and heating components. Refer to manufacturer documentation for exact electrical ratings, calibration procedures and service limits.
Spare Parts: Keep door or lid seals, thermostats or temperature sensors, selected heating elements, pumps or fans where applicable, fuses, switches and manufacturer-recommended control parts. High-use passenger vessels may justify additional wear components. Verify all electrical and mechanical parts against the appliance nameplate.
Use Cases: Food preparation, cleaning and catering service in merchant-ship, ferry, cruise-ship and offshore galley installations.
Dishwasher XL 400V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
400
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating or drive component failure caused by wear, overheating or electrical faults, resulting in slow operation, no heat or inability to complete the normal cycle
- Temperature, level or control-sensor malfunction caused by drift or component failure, resulting in unstable operation, alarms or incorrect temperature
- Door, lid, seal or duct deterioration caused by repeated use and heat, resulting in leakage, heat loss or poor extraction
- Electrical-control fault caused by moisture, loose terminals or failed relays, resulting in intermittent operation or breaker trips
- Drain, filter, grease path or ventilation restriction where applicable caused by food deposits or poor cleaning, resulting in leakage, odor, overheating or reduced performance
Service: Keep heating surfaces, filters, drains, grease paths and ventilation openings clean as applicable to the appliance. Inspect electrical terminals, controls, doors, guards and safety interlocks for heat damage or looseness. Verify temperature or cycle control using the vessel's approved maintenance method and investigate repeated overheating or breaker trips. Check secure fastening to the galley structure and inspect flexible service connections where fitted. Use cleaning chemicals compatible with stainless steel, seals and heating components. Refer to manufacturer documentation for exact electrical ratings, calibration procedures and service limits.
Spare Parts: Keep door or lid seals, thermostats or temperature sensors, selected heating elements, pumps or fans where applicable, fuses, switches and manufacturer-recommended control parts. High-use passenger vessels may justify additional wear components. Verify all electrical and mechanical parts against the appliance nameplate.
Use Cases: Food preparation, cleaning and catering service in merchant-ship, ferry, cruise-ship and offshore galley installations.
Dishwasher XL 440V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
440
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating or drive component failure caused by wear, overheating or electrical faults, resulting in slow operation, no heat or inability to complete the normal cycle
- Temperature, level or control-sensor malfunction caused by drift or component failure, resulting in unstable operation, alarms or incorrect temperature
- Door, lid, seal or duct deterioration caused by repeated use and heat, resulting in leakage, heat loss or poor extraction
- Electrical-control fault caused by moisture, loose terminals or failed relays, resulting in intermittent operation or breaker trips
- Drain, filter, grease path or ventilation restriction where applicable caused by food deposits or poor cleaning, resulting in leakage, odor, overheating or reduced performance
Service: Keep heating surfaces, filters, drains, grease paths and ventilation openings clean as applicable to the appliance. Inspect electrical terminals, controls, doors, guards and safety interlocks for heat damage or looseness. Verify temperature or cycle control using the vessel's approved maintenance method and investigate repeated overheating or breaker trips. Check secure fastening to the galley structure and inspect flexible service connections where fitted. Use cleaning chemicals compatible with stainless steel, seals and heating components. Refer to manufacturer documentation for exact electrical ratings, calibration procedures and service limits.
Spare Parts: Keep door or lid seals, thermostats or temperature sensors, selected heating elements, pumps or fans where applicable, fuses, switches and manufacturer-recommended control parts. High-use passenger vessels may justify additional wear components. Verify all electrical and mechanical parts against the appliance nameplate.
Use Cases: Food preparation, cleaning and catering service in merchant-ship, ferry, cruise-ship and offshore galley installations.
RATIONAL Marine
12
Dishwasher Small 230V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
230
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner or thermostat faults caused by ageing, contamination or control failure can result in slow heating, overheating or failure to reach operating condition
- Door, seal or gasket deterioration caused by heat and repeated use can cause heat loss, steam leakage or poor washing performance
- Drain, spray or filter blockage caused by food debris or scale can produce poor cleaning, standing water or overflow
- Switch, contactor or control-board faults caused by moisture or component wear can lead to intermittent operation or failure to start
- Ventilation or cooling obstruction caused by grease or dust can increase appliance temperature and cause nuisance trips or component damage
Service: Inspect cleanliness, guards, wiring, controls, seals, drains, ventilation and utility connections. Confirm safety cut-outs and protective devices operate without bypassing them, and remove grease or scale according to the maker's procedure. Refer to manufacturer documentation for exact electrical, gas, temperature and service values.
Spare Parts: Useful spares include seals, heating or control components, filters, switches, contactors, fuses, spray or drain parts and other maker-approved consumables suited to the appliance.
Use Cases: Merchant, passenger, ferry and offshore-vessel galleys and catering spaces.
Dishwasher Small 400V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
400
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner or thermostat faults caused by ageing, contamination or control failure can result in slow heating, overheating or failure to reach operating condition
- Door, seal or gasket deterioration caused by heat and repeated use can cause heat loss, steam leakage or poor washing performance
- Drain, spray or filter blockage caused by food debris or scale can produce poor cleaning, standing water or overflow
- Switch, contactor or control-board faults caused by moisture or component wear can lead to intermittent operation or failure to start
- Ventilation or cooling obstruction caused by grease or dust can increase appliance temperature and cause nuisance trips or component damage
Service: Inspect cleanliness, guards, wiring, controls, seals, drains, ventilation and utility connections. Confirm safety cut-outs and protective devices operate without bypassing them, and remove grease or scale according to the maker's procedure. Refer to manufacturer documentation for exact electrical, gas, temperature and service values.
Spare Parts: Useful spares include seals, heating or control components, filters, switches, contactors, fuses, spray or drain parts and other maker-approved consumables suited to the appliance.
Use Cases: Merchant, passenger, ferry and offshore-vessel galleys and catering spaces.
Dishwasher Small 440V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
440
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner or thermostat faults caused by ageing, contamination or control failure can result in slow heating, overheating or failure to reach operating condition
- Door, seal or gasket deterioration caused by heat and repeated use can cause heat loss, steam leakage or poor washing performance
- Drain, spray or filter blockage caused by food debris or scale can produce poor cleaning, standing water or overflow
- Switch, contactor or control-board faults caused by moisture or component wear can lead to intermittent operation or failure to start
- Ventilation or cooling obstruction caused by grease or dust can increase appliance temperature and cause nuisance trips or component damage
Service: Inspect cleanliness, guards, wiring, controls, seals, drains, ventilation and utility connections. Confirm safety cut-outs and protective devices operate without bypassing them, and remove grease or scale according to the maker's procedure. Refer to manufacturer documentation for exact electrical, gas, temperature and service values.
Spare Parts: Useful spares include seals, heating or control components, filters, switches, contactors, fuses, spray or drain parts and other maker-approved consumables suited to the appliance.
Use Cases: Merchant, passenger, ferry and offshore-vessel galleys and catering spaces.
Dishwasher Medium 230V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
230
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner or thermostat faults caused by ageing, contamination or control failure can result in slow heating, overheating or failure to reach operating condition
- Door, seal or gasket deterioration caused by heat and repeated use can cause heat loss, steam leakage or poor washing performance
- Drain, spray or filter blockage caused by food debris or scale can produce poor cleaning, standing water or overflow
- Switch, contactor or control-board faults caused by moisture or component wear can lead to intermittent operation or failure to start
- Ventilation or cooling obstruction caused by grease or dust can increase appliance temperature and cause nuisance trips or component damage
Service: Inspect cleanliness, guards, wiring, controls, seals, drains, ventilation and utility connections. Confirm safety cut-outs and protective devices operate without bypassing them, and remove grease or scale according to the maker's procedure. Refer to manufacturer documentation for exact electrical, gas, temperature and service values.
Spare Parts: Useful spares include seals, heating or control components, filters, switches, contactors, fuses, spray or drain parts and other maker-approved consumables suited to the appliance.
Use Cases: Merchant, passenger, ferry and offshore-vessel galleys and catering spaces.
Dishwasher Medium 400V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
400
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner or thermostat faults caused by ageing, contamination or control failure can result in slow heating, overheating or failure to reach operating condition
- Door, seal or gasket deterioration caused by heat and repeated use can cause heat loss, steam leakage or poor washing performance
- Drain, spray or filter blockage caused by food debris or scale can produce poor cleaning, standing water or overflow
- Switch, contactor or control-board faults caused by moisture or component wear can lead to intermittent operation or failure to start
- Ventilation or cooling obstruction caused by grease or dust can increase appliance temperature and cause nuisance trips or component damage
Service: Inspect cleanliness, guards, wiring, controls, seals, drains, ventilation and utility connections. Confirm safety cut-outs and protective devices operate without bypassing them, and remove grease or scale according to the maker's procedure. Refer to manufacturer documentation for exact electrical, gas, temperature and service values.
Spare Parts: Useful spares include seals, heating or control components, filters, switches, contactors, fuses, spray or drain parts and other maker-approved consumables suited to the appliance.
Use Cases: Merchant, passenger, ferry and offshore-vessel galleys and catering spaces.
Dishwasher Medium 440V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
440
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner or thermostat faults caused by ageing, contamination or control failure can result in slow heating, overheating or failure to reach operating condition
- Door, seal or gasket deterioration caused by heat and repeated use can cause heat loss, steam leakage or poor washing performance
- Drain, spray or filter blockage caused by food debris or scale can produce poor cleaning, standing water or overflow
- Switch, contactor or control-board faults caused by moisture or component wear can lead to intermittent operation or failure to start
- Ventilation or cooling obstruction caused by grease or dust can increase appliance temperature and cause nuisance trips or component damage
Service: Inspect cleanliness, guards, wiring, controls, seals, drains, ventilation and utility connections. Confirm safety cut-outs and protective devices operate without bypassing them, and remove grease or scale according to the maker's procedure. Refer to manufacturer documentation for exact electrical, gas, temperature and service values.
Spare Parts: Useful spares include seals, heating or control components, filters, switches, contactors, fuses, spray or drain parts and other maker-approved consumables suited to the appliance.
Use Cases: Merchant, passenger, ferry and offshore-vessel galleys and catering spaces.
Dishwasher Large 230V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
230
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner or thermostat faults caused by ageing, contamination or control failure can result in slow heating, overheating or failure to reach operating condition
- Door, seal or gasket deterioration caused by heat and repeated use can cause heat loss, steam leakage or poor washing performance
- Drain, spray or filter blockage caused by food debris or scale can produce poor cleaning, standing water or overflow
- Switch, contactor or control-board faults caused by moisture or component wear can lead to intermittent operation or failure to start
- Ventilation or cooling obstruction caused by grease or dust can increase appliance temperature and cause nuisance trips or component damage
Service: Inspect cleanliness, guards, wiring, controls, seals, drains, ventilation and utility connections. Confirm safety cut-outs and protective devices operate without bypassing them, and remove grease or scale according to the maker's procedure. Refer to manufacturer documentation for exact electrical, gas, temperature and service values.
Spare Parts: Useful spares include seals, heating or control components, filters, switches, contactors, fuses, spray or drain parts and other maker-approved consumables suited to the appliance.
Use Cases: Merchant, passenger, ferry and offshore-vessel galleys and catering spaces.
Dishwasher Large 400V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
400
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner or thermostat faults caused by ageing, contamination or control failure can result in slow heating, overheating or failure to reach operating condition
- Door, seal or gasket deterioration caused by heat and repeated use can cause heat loss, steam leakage or poor washing performance
- Drain, spray or filter blockage caused by food debris or scale can produce poor cleaning, standing water or overflow
- Switch, contactor or control-board faults caused by moisture or component wear can lead to intermittent operation or failure to start
- Ventilation or cooling obstruction caused by grease or dust can increase appliance temperature and cause nuisance trips or component damage
Service: Inspect cleanliness, guards, wiring, controls, seals, drains, ventilation and utility connections. Confirm safety cut-outs and protective devices operate without bypassing them, and remove grease or scale according to the maker's procedure. Refer to manufacturer documentation for exact electrical, gas, temperature and service values.
Spare Parts: Useful spares include seals, heating or control components, filters, switches, contactors, fuses, spray or drain parts and other maker-approved consumables suited to the appliance.
Use Cases: Merchant, passenger, ferry and offshore-vessel galleys and catering spaces.
Dishwasher Large 440V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
440
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner or thermostat faults caused by ageing, contamination or control failure can result in slow heating, overheating or failure to reach operating condition
- Door, seal or gasket deterioration caused by heat and repeated use can cause heat loss, steam leakage or poor washing performance
- Drain, spray or filter blockage caused by food debris or scale can produce poor cleaning, standing water or overflow
- Switch, contactor or control-board faults caused by moisture or component wear can lead to intermittent operation or failure to start
- Ventilation or cooling obstruction caused by grease or dust can increase appliance temperature and cause nuisance trips or component damage
Service: Inspect cleanliness, guards, wiring, controls, seals, drains, ventilation and utility connections. Confirm safety cut-outs and protective devices operate without bypassing them, and remove grease or scale according to the maker's procedure. Refer to manufacturer documentation for exact electrical, gas, temperature and service values.
Spare Parts: Useful spares include seals, heating or control components, filters, switches, contactors, fuses, spray or drain parts and other maker-approved consumables suited to the appliance.
Use Cases: Merchant, passenger, ferry and offshore-vessel galleys and catering spaces.
Dishwasher XL 230V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
230
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher XL 400V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
400
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher XL 440V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
440
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Rieber Marine
12
Dishwasher Small 230V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
230
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher Small 400V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
400
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher Small 440V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
440
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher Medium 230V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
230
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner or thermostat faults caused by ageing, contamination or control failure can result in slow heating, overheating or failure to reach operating condition
- Door, seal or gasket deterioration caused by heat and repeated use can cause heat loss, steam leakage or poor washing performance
- Drain, spray or filter blockage caused by food debris or scale can produce poor cleaning, standing water or overflow
- Switch, contactor or control-board faults caused by moisture or component wear can lead to intermittent operation or failure to start
- Ventilation or cooling obstruction caused by grease or dust can increase appliance temperature and cause nuisance trips or component damage
Service: Inspect cleanliness, guards, wiring, controls, seals, drains, ventilation and utility connections. Confirm safety cut-outs and protective devices operate without bypassing them, and remove grease or scale according to the maker's procedure. Refer to manufacturer documentation for exact electrical, gas, temperature and service values.
Spare Parts: Useful spares include seals, heating or control components, filters, switches, contactors, fuses, spray or drain parts and other maker-approved consumables suited to the appliance.
Use Cases: Merchant, passenger, ferry and offshore-vessel galleys and catering spaces.
Dishwasher Medium 400V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
400
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner or thermostat faults caused by ageing, contamination or control failure can result in slow heating, overheating or failure to reach operating condition
- Door, seal or gasket deterioration caused by heat and repeated use can cause heat loss, steam leakage or poor washing performance
- Drain, spray or filter blockage caused by food debris or scale can produce poor cleaning, standing water or overflow
- Switch, contactor or control-board faults caused by moisture or component wear can lead to intermittent operation or failure to start
- Ventilation or cooling obstruction caused by grease or dust can increase appliance temperature and cause nuisance trips or component damage
Service: Inspect cleanliness, guards, wiring, controls, seals, drains, ventilation and utility connections. Confirm safety cut-outs and protective devices operate without bypassing them, and remove grease or scale according to the maker's procedure. Refer to manufacturer documentation for exact electrical, gas, temperature and service values.
Spare Parts: Useful spares include seals, heating or control components, filters, switches, contactors, fuses, spray or drain parts and other maker-approved consumables suited to the appliance.
Use Cases: Merchant, passenger, ferry and offshore-vessel galleys and catering spaces.
Dishwasher Medium 440V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
440
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner or thermostat faults caused by ageing, contamination or control failure can result in slow heating, overheating or failure to reach operating condition
- Door, seal or gasket deterioration caused by heat and repeated use can cause heat loss, steam leakage or poor washing performance
- Drain, spray or filter blockage caused by food debris or scale can produce poor cleaning, standing water or overflow
- Switch, contactor or control-board faults caused by moisture or component wear can lead to intermittent operation or failure to start
- Ventilation or cooling obstruction caused by grease or dust can increase appliance temperature and cause nuisance trips or component damage
Service: Inspect cleanliness, guards, wiring, controls, seals, drains, ventilation and utility connections. Confirm safety cut-outs and protective devices operate without bypassing them, and remove grease or scale according to the maker's procedure. Refer to manufacturer documentation for exact electrical, gas, temperature and service values.
Spare Parts: Useful spares include seals, heating or control components, filters, switches, contactors, fuses, spray or drain parts and other maker-approved consumables suited to the appliance.
Use Cases: Merchant, passenger, ferry and offshore-vessel galleys and catering spaces.
Dishwasher Large 230V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
230
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher Large 400V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
400
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher Large 440V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
440
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher XL 230V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
230
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher XL 400V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
400
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.
Dishwasher XL 440V Marine
unverified
· 10.0 kW
Power (kW)
10
Voltage (V)
440
Capacity
standard
Fuel
electric
Common Failures & Inspection Points
- Heating-element, burner, thermostat, or temperature-control failure causes slow heating, overheating, or inability to reach the selected condition
- Pump, fan, motor, or drive faults cause poor circulation, washing, extraction, or cooling depending on the appliance
- Scale, grease, food debris, or blocked filters and drains reduce performance and can cause leakage, odors, or trips
- Door seal, hose, valve, or connection deterioration causes water, steam, gas, or condensate leakage
- Electrical supply, switch, sensor, or control-board faults cause intermittent operation, failed cycles, or protective trips
Service: Inspect cleanliness, guards, doors and seals, electrical supply and earthing, hoses, drains, filters, thermostats, safety cut-outs, ventilation, and leakage. Clean and descale as appropriate and follow the manufacturer documentation for exact electrical, gas, and temperature settings.
Spare Parts: Typical spares include door and connection seals, filters, heating or ignition components, switches, thermostats, fuses, pump or fan service items, and critical control parts recommended for the appliance.
Use Cases: Used on merchant, passenger, offshore, ferry, naval, and accommodation vessels to support crew and passenger hotel services.