High Velocity Vent Valve
A high velocity vent valve is the PV valve variant built to discharge cargo vapor upward at speed so it disperses well clear of the deck, rather than simply relieving pressure locally, which is what separates it from a standard pressure/vacuum breaker.
What to check on a High Velocity Vent Valve.
7 models from Emerson Marine in High Velocity Vent Valve. Below: the full model list.
What Sets a High Velocity Vent Valve Apart
Standard PV valves protect the tank against over- and under-pressure but do little to control where the vented vapor goes once it leaves the valve. A high velocity vent valve is built with a narrowed outlet orifice so that, once it opens, gas escapes at high jet speed, typically well above 30 metres per second, so the flammable vapor cloud is thrown clear of the deck instead of rolling across it toward accommodation or ignition sources. It is not a separate protective function from the PV valve, it is the same overpressure and vacuum protection built with a discharge geometry aimed at safe dispersal. On tankers venting flammable cargo vapor this dispersal behaviour is the entire point of the design, and it is why these valves are fitted at the top of the venting mast rather than lower on the tank.
Legend
- deflector head
- loading weight
- high-velocity vapor jet
- valve body
- seat
- pallet (disc)
- riser from tank
- deck / tank connection
- cargo tank below deck
Main Components
Pressure Pallet and Vacuum Pallet
Two independent, spring-loaded discs that lift at their respective set pressures, one for overpressure relief on loading or heating, one for vacuum relief on discharge or cooling.
High Velocity Outlet Head
The shaped nozzle section that accelerates the escaping gas, distinguishing this valve from a low-velocity or free-vent design.
Read the full guide
Flame Screen or Deflagration Element
Where fitted for cargoes requiring it, a screen intended to arrest flame propagation into the tank; not all high velocity valves carry one, and the valve should not be assumed fire-safe without checking the specific approval.
Weather Cover / Bird Guard
A cap that keeps rain, salt spray and debris off the pallets without restricting the vent path when the valve lifts.
Selection and Sizing
- Required venting capacity in cubic metres per hour, sized against the tank's maximum loading and discharge rates plus thermal venting.
- Set pressures for both the pressure and vacuum pallets, matched to the tank design pressure and the cargo's vapour characteristics.
- Discharge velocity achieved at the design flow, which must clear the deck safety distance required for the cargo class carried.
- Material compatibility with the cargo vapour, since some chemical cargoes attack standard valve trim materials.
Regulations and Class
High velocity vent valves on tankers fall under SOLAS Chapter II-2 venting arrangements for cargo tanks and under MARPOL Annex I or II venting provisions depending on cargo type, with set pressures and capacities reviewed against the ship's approved venting calculations. Class rules require these valves to be type-tested and certified for their rated capacity and set pressure, and they are subject to periodic testing, typically annually, to confirm the pallets lift and reseat within tolerance. A valve found stuck or fouled at survey is a recurring deficiency category on tanker inspections.
Typical Faults
| Fault | Cause | Consequence |
|---|---|---|
| Pallet stuck closed | Polymerized cargo residue, corrosion, or paint overspray on the seat | Tank overpressure during loading or heating, risk of structural failure |
| Pallet stuck open | Debris on the seat or spring fatigue | Continuous vapour loss and loss of tank inerting or gas-free status |
| Set pressure drift | Spring fatigue or incorrect adjustment after maintenance | Valve lifts too early or too late relative to design intent |
| Blocked flame screen | Residue buildup not cleaned during routine maintenance | Restricted flow area, effective venting capacity below rated value |
What to Look for in a Supplier
- Type approval certificate showing tested capacity and velocity at the specific set pressures ordered, not a generic catalogue figure.
- Trim materials confirmed against the cargo list the vessel actually carries, especially for chemical tankers with varying cargoes.
- A maintenance kit and seat material that can be serviced on board without returning the whole valve ashore.
- Documented annual test procedure compatible with the ship's own test rig or portable test equipment.
A high velocity vent valve that lifts quietly and closes with a solid seated feel is doing its job; one that seeps continuously after closing has already lost its dispersal margin, not just a little cargo.
Models in this type.
The best-documented model of each manufacturer first, then the next — 7 of 7 models in High Velocity Vent Valve. Every row links to full specifications, documents and service notes.
Manufacturers.
All 9 manufacturers with models of High Velocity Vent Valve. Names with a manufacturer page open it; the others open a search across the full library.
All manufacturers in the libraryAlso in PV Valves & Vent Systems.
The other equipment types in this category.
Inspection findings for this equipment
From public port state control and US Coast Guard records; OceanSphere assigns them to this equipment type from the descriptions.
Deficiency codes – USCG port state control – foreign-flag vessels
- 02126 · Cargo tank vent system – 49 findings
USCG components
- Cargo tank vent system – 111 findings
Write to us about your machine — the answer comes by e-mail.
Name the make and the model and what the job is: a spare, a service call, a second opinion on a data sheet. We answer by e-mail.
No details at hand? A photo of the rating plate or the part is enough — simply attach it to the request.
Questions that come up with this equipment.
Is High Velocity Vent Valve data free?
Yes. Every model page, every guide and every datasheet for this type is readable without an account. An account adds saved searches and requests, nothing is taken away.
My model is missing — what now?
Send us the nameplate. We identify it by hand, add it to the library, and if you need a part or a service, the request is already on our desk.
Can you source a High Velocity Vent Valve part?
Yes. Tell us the manufacturer, the model and what you need — a person reads every request and replies by e-mail.