OceanSphereENGINES

5X35

Main Engine 2-Stroke · Main Engines (2-Stroke)

Technical data from manufacturer or class sources · not yet verified by a person​​‍‌‌⁠​⁠⁠‌‌⁠​‌‍​‌⁠​⁠
4,450 kWPower
5Cylinders
350 mmBore
1,550 mmStroke
167 rpmMCR RPM

The WinGD 5X35 is a low-speed, five‑cylinder, two‑stroke marine diesel engine delivering up to 4 450 kW at 167 rpm, distinguished by its electronic common‑rail fuel system and WiDE intelligent control platform.

Specifications

Technical data.reference — unverified

Do you have the manufacturer datasheet for this model? Send it with the enquiry form — we check it and name the source.

BoreX35-B: 350 mm
StrokeX35-B: 1550 mm
Stroke/Bore Ratio4.43 (both models)
Power RangeX35-B: 2,450–6,960 kW
RPM RangeX35-B: 118–167 rpm
SFOC (Specific Fuel Oil Consumption)X35-B: ~175.8 g/kWh
Fuel TypeMarine Diesel (HFO/MDO) - Single-Fuel; X40DF-Variante: LNG Dual-Fuel
Fuel Injection SystemElectronically Controlled Common Rail mit Zeit-gesteuerte Einspritzung
Emissions ComplianceIMO Tier II/Tier III (SCR-Nachrüstung für Tier III)
Production StatusLegacy (Produktion beendet, technische Unterstützung aktiv)
Inspection

Inspector Detail

Designation decoded

WinGD 5X35 – 5-cylinder in-line engine, X-series (latest generation), 35 = 350 mm bore. Two-stroke crosshead diesel engine with fully electronic control (camshaft-less). WinGD = Winterthur Gas & Diesel (formerly Wärtsilä two-stroke division, owned by CSSC since 2015). 350 mm bore, 1550 mm stroke, 5 cylinders.

Background

The WinGD X35 belongs to the X-series, the latest generation of fully electronically controlled two-stroke crosshead engines from WinGD. The X-series is the successor to the Sulzer RT-flex series (which in turn was the successor to the RTA). The concept is completely camshaft-less: fuel injection is via an electronically controlled common-rail high-pressure system (W-FIS = WinGD Fuel Injection System), exhaust valve control via hydraulic actuators (W-EVC = WinGD Exhaust Valve Control). The entire engine control runs via the UNIC system (Unified Controls). FlexCam enables flexible electronic cam profiles for various operating modes. Delta Tuning optimizes the engine for slow-steaming operation. The X35 is the smallest engine in the X-series, designed for small commercial vessels and feeder container ships. The 5-cylinder configuration requires special attention to torsional vibrations. iCER (intelligent Control by Exhaust Recycling) can be retrofitted for IMO Tier III compliance.

Calculated metrics

Stroke to bore ratio4.429

Inspector checklist

  • Common-rail high-pressure system (W-FIS): Check accumulators, high-pressure lines, and injectors for leaks and pressure retention
  • Hydraulic exhaust valve control (W-EVC): Check hydraulic pressure, valve lift, and closing damping
  • UNIC control system: Read fault memory, check sensors (pressure transducers, speed sensors, temperature sensors)
  • Pulse Lubrication System (cylinder lubrication): Check dosing, distributors, and condition monitoring
  • Torsional vibration damper: Particularly important for 5-cylinder configuration – check condition and silicone filling

Logbook reference values

ParameterExpectedDeviation means
Firing pressures (Pmax) of all 5 cylindersPmax deviation ≤ ±2 bar between cylinders (electronic control allows for tighter tolerances)With electronic control, deviations >2 bar indicate injector malfunction, W-EVC problems, or sensor errors
Exhaust gas temperatures per cylinder340–420 °C at rated loadAsymmetries indicate injector degradation, exhaust valve leakage, or errors in electronic timing
Common-rail pressure (W-FIS)800–1000 bar (load-dependent, system-specific)Pressure drop indicates injector leakage, high-pressure pump wear, or pressure control valve malfunction
Exhaust valve hydraulic pressure (W-EVC)According to WinGD specification, typically 200–300 barDeviations may indicate hydraulic leaks, defective actuators, or control valve errors
Scavenge air pressure1.5–3.0 bar abs. (load-dependent)Too low pressure indicates turbocharger fouling or charge air cooler problems
Cylinder oil consumption (Pulse Lubrication)0.5–1.0 g/kWh (load-dependent optimized)Increased consumption with simultaneously poor running condition indicates system failure or incorrect oil quality

Common Failure Modes

  • Common rail injector coking or wear

    Symptoms: Increased exhaust gas temperature at the affected cylinder Altered combustion pattern Pmax deviation despite electronic correction

    Causes: Fuel quality (catalytic fines, asphaltenes), Inadequate fuel treatment, Nozzle needle wear

    Preventive: Carefully monitor fuel treatment (separators), adhere to injector maintenance intervals per WinGD Service Letter, utilize UNIC combustion monitoring

  • W-EVC hydraulic system leakage

    Symptoms: Irregular valve lift Increased hydraulic oil consumption Fault messages in the UNIC system

    Causes: Seal wear on hydraulic actuators, Hydraulic oil contamination, Thermal fatigue of high-pressure components

    Preventive: Regularly check hydraulic oil cleanliness (particle counting), replace seals according to maintenance plan, evaluate UNIC diagnostic data

  • Torsional vibration issues (5-cylinder specific)

    Symptoms: Unusual vibrations in the lower speed range Noise from the vibration damper Increased wear on drive components

    Causes: Operation in prohibited speed ranges (Barred Speed Range), Vibration damper degradation, Propeller resonance

    Preventive: Strictly adhere to Barred Speed Range, inspect torsional vibration damper at every docking, document torsional vibration behavior during sea trials

Expert tips

  • The fully electronic control of the X35 enables very tight tolerances (Pmax ±2 bar) – deviations that would be acceptable on conventional engines are already a warning signal for component issues here
  • Verify the Barred Speed Range for 5-cylinder engines at the wheelhouse and bridge console – rapid traversal must be ensured
  • Check the UNIC fault memory not only for active faults but also for historical entries – recurring temporary faults may indicate gradual degradation

Related components

  • Common rail high-pressure pumps and accumulators
  • UNIC control units (CCU, ECU, FCM)
  • Hydraulic oil conditioning system for W-EVC
  • Turbocharger and charge air cooler
  • Pulse Lubrication System (metering pumps, distributors)
  • Torsional vibration damper
  • Fuel treatment plant (separators, preheaters)

Classification & regulatory

IMO Tier II compliance as standard. Tier III possible via iCER (intelligent Control by Exhaust Recycling) or SCR retrofit. Check NOx Technical File and EIAPP Certificate. For operation with Delta Tuning: class approval for deviating engine parameters is required. Verify UNIC software version against approved baseline – unauthorized software updates may affect NOx compliance.

Reference content for inspector orientation. Always verify against manufacturer's manual, latest service letters and class society requirements.

Need this part?

Request a quote for this model.

Free of charge — send us your request for WinGD equipment. Our team checks it and replies by e-mail.

For marine equipment hardly any maker or authorised dealer will name a price while the vessel is unknown. With the vessel details, availability and price can be settled faster; without them we may have to ask first, which costs a few days. If you are not allowed to name the vessel, a photo of the rating plate is enough — attach it below or send it as a reply to our confirmation e-mail.

Your contact details are not published. No account required.
Related models

Also in Main Engine 2-Stroke.

Other models of the same equipment type, WinGD first.

By manufacturer MAN Energy SolutionsWinGDSulzerWärtsiläMitsubishiElectro-Motive DieselHyundaiDoosanHudong-ZhonghuaJapan EngineAkasaka Diesel (Mitsubishi UEC licensed)National Railway EquipmentHSD EngineKawasakiProgress Rail Locomotive, Inc.All manufacturersSpare parts by equipmentNew here? Create a free account Can't read the plate? Try the nameplate scanner All WinGD models More like 5X35
More than the data sheet shows

We answer by e-mail, never with an automatic reply.

Tell us what you need for this WinGD 5X35 — a part, a service call, a second opinion. Are you WinGD? Claim this brand page.

Service engineer? Write the day report for this 5X35 in OceanSphere Work — photos, hours and parts, as a PDF for the owner. Try it free for 14 days →

Frequently asked

Questions that come up with this equipment.

Is this model's data free?

Yes. Specifications, documents and service notes for this model are readable without an account. An account adds saved searches and requests, nothing is taken away.

Can you find a part for this exact model?

Yes. Tell us the manufacturer, the model and what you need — a person reads every request and replies by e-mail.

The specifications look wrong — what now?

Send us the nameplate or the correct value. We check it against the manufacturer datasheet or class-society record and update the page.