OceanSphereENGINES
Library› Engine Room› Turbochargers› Turbocharger› Hitachi HT-S HT-68S
Hitachi

HT-S HT-68S

Turbocharger · Turbochargers

Technical data from manufacturer or class sources · not yet verified by a person​‍​‍⁠⁠‌‌​​‌​‍‌⁠‌‍⁠​⁠
Hitachi in the SpecCodex register — view brand page →

Hitachi HT-S HT-68S — HT-S, 30000 kW max.

Specifications

Technical data.reference — unverified

Do you have the manufacturer datasheet for this model? Send it with the enquiry form — we check it and name the source.

Frame SizeHT-68S
Power max (kW)30000
Inspection

Inspector Detail

Common issues

  • Bearing wear and failure (thrust and journal bearings), often due to lubrication issues, contamination, or excessive vibration.
  • Compressor wheel fouling or erosion, leading to reduced efficiency, surging, and potential imbalance.
  • Turbine blade erosion or fouling from exhaust gas contaminants, leading to reduced power and efficiency.
  • Oil leakage from bearing housings, often through worn labyrinth seals or damaged O-rings, leading to oil consumption and potential fire hazard.
  • Rotor imbalance due to blade damage, uneven fouling, or bearing wear, causing excessive vibration and accelerated component wear.
  • Cracks in turbine or compressor casings, especially around high-stress areas or due to thermal cycling.
  • Nozzle ring and diffuser damage or excessive fouling, restricting gas flow and impacting performance.
  • Turbocharger surging, indicated by fluctuating boost pressure and characteristic 'whooshing' sounds, often due to engine load changes, air filter blockage, or compressor fouling.

Inspection checklist

  • Check turbocharger lubricating oil pressure and temperature, ensuring it's within manufacturer's specified range (e.g., 2-4 bar, 50-70°C).
  • Inspect for any oil or exhaust gas leakages from casings, connections, and drain lines.
  • Perform a manual check of rotor axial (end float) and radial clearances (rocking), comparing against manufacturer's limits (e.g., axial float 0.1-0.3 mm, radial play 0.05-0.15 mm).
  • Inspect compressor wheel for fouling, erosion, foreign object damage (FOD), and rubbing marks on the casing.
  • Inspect turbine wheel and blades for erosion, cracks, burning, and heavy carbon deposits (fouling).
  • Check the condition of the air filter elements for cleanliness and integrity.
  • Verify the integrity of all mounting bolts, anti-vibration mounts, and exhaust gas/air duct connections.
  • Inspect the condition of the insulation on the turbine casing and exhaust gas piping for damage or signs of overheating.
  • Check the functionality of the turbocharger speed sensor and overspeed trip mechanism (if accessible and safe to test).

Service intervals

Routine visual inspection (external)Daily/Weekly
Lubricating oil filter element replacement1,000 - 2,000 running hours
Bearing inspection and axial/radial clearance check4,000 - 8,000 running hours (or annually)
Compressor and turbine side cleaning (water wash/dry wash)500 - 1,500 running hours (as required by performance monitoring)
Bearing cartridge replacement (preventive)8,000 - 16,000 running hours
Major overhaul (rotor balancing, full disassembly, inspection, and replacement of wear parts)12,000 - 24,000 running hours (or every 3-5 years)

Typical intervals for this design class, not the manufacturer’s figures for your model. The manufacturer’s manual is binding.

Typical wear limits

Axial (end) clearance of rotorMax. 0.30 - 0.45 mm (check specific model manual)
Radial clearance of rotor (bearing play)Max. 0.15 - 0.25 mm (check specific model manual)
Compressor wheel blade tip clearanceMax. 0.5 - 1.0 mm (check for rubbing marks)
Turbine wheel blade tip clearanceMax. 0.8 - 1.5 mm (check for rubbing marks)
Nozzle ring opening (if adjustable)Deviation from new condition typically +/- 5% (check for erosion/fouling)
Shaft diameter at bearing journalsMax. 0.02 - 0.05 mm ovality or wear from new diameter

Ranges are typical for this design class. Always confirm against the manufacturer documentation for your serial number.

Critical spares

  • Complete bearing cartridge assembly (thrust and journal bearings)
  • Full set of O-rings and gaskets for casing joints and oil lines
  • Labyrinth seals (oil and air side)
  • Lubricating oil filter elements
  • Nozzle ring segments or complete nozzle ring
  • Diffuser segments or complete diffuser
  • Mounting bolts and nuts (high-temperature resistant)

Safety

  • High surface temperatures of turbine casing and exhaust piping (can exceed 400°C), posing severe burn risks. Ensure insulation is intact.
  • High rotational speeds (up to 15,000-20,000 RPM for this size), leading to potential rotor disintegration in case of catastrophic failure. Always ensure overspeed trip is functional.
  • High pressure in compressor discharge and exhaust gas lines. Ensure all connections are secure and pressure relief valves (if fitted) are operational.
  • Hot oil spray or leakage from bearing housings, which can ignite on hot surfaces, leading to engine room fires.
  • Noise levels can be extremely high during operation; hearing protection is mandatory in the vicinity.

Class survey

Class surveyors will typically review the turbocharger's maintenance records, including bearing clearances, cleaning logs, and any reported performance issues. They will visually inspect the external condition for leaks, cracks, and proper insulation. Performance parameters like boost pressure, exhaust gas temperatures (before and after turbine), and turbocharger RPM will be checked against design values. If the turbocharger has been opened for maintenance, the surveyor may request to witness bearing clearance measurements and inspect the condition of the rotor, nozzle ring, and diffuser. The functionality of the overspeed trip device and associated alarms will also be verified.

Estimated lifetime: 12,000 - 24,000 running hours before major overhaul, with proper maintenance and bearing replacements. Total design life can exceed 100,000 hours with continuous component replacement.

Need this part?

Request a quote for this model.

Free of charge — send us your request for Hitachi equipment. Our team checks it and replies by e-mail.

For marine equipment hardly any maker or authorised dealer will name a price while the vessel is unknown. With the vessel details, availability and price can be settled faster; without them we may have to ask first, which costs a few days. If you are not allowed to name the vessel, a photo of the rating plate is enough — attach it below or send it as a reply to our confirmation e-mail.

Your contact details are not published. No account required.
Related models

Also in Turbocharger.

Other models of the same equipment type, Hitachi first.

By manufacturer ABBMAN Energy SolutionsIHIMitsubishiABB Turbocharging / AccelleronKawasakiPBSTCummins Holset TurbochargersNapierMAN ES TurbochargingMitsubishi METGarrett Motion MarineVolvo Pentaengine.od / Other TurbochargersKBB TurboAll manufacturersSpare parts by equipmentNew here? Create a free account Can't read the plate? Try the nameplate scanner More like HT-S HT-68S
More than the data sheet shows

We answer by e-mail, never with an automatic reply.

Tell us what you need for this Hitachi HT-S HT-68S — a part, a service call, a second opinion. Are you Hitachi? Claim this brand page.

Service engineer? Write the day report for this HT-S HT-68S in OceanSphere Work — photos, hours and parts, as a PDF for the owner. Try it free for 14 days →

Frequently asked

Questions that come up with this equipment.

Is this model's data free?

Yes. Specifications, documents and service notes for this model are readable without an account. An account adds saved searches and requests, nothing is taken away.

Can you find a part for this exact model?

Yes. Tell us the manufacturer, the model and what you need — a person reads every request and replies by e-mail.

The specifications look wrong — what now?

Send us the nameplate or the correct value. We check it against the manufacturer datasheet or class-society record and update the page.