⚓ Working on this equipment?
Ask the AI troubleshooter, log your hours on board and turn them into invoice-ready service reports — for this exact model.
Start free — 14 days →
No credit card required
🔧 5 verified suppliers & service companies for MAN Energy Solutions in the Maritime Network
Find suppliers →
MAN Energy Solutions
6S40ME-C9.6
The MAN 6S40ME-C9.6 is a low‑speed, six‑cylinder, two‑stroke marine diesel engine delivering up to 9 420 kW at 146 rpm, distinguished by its fully electronic ELFI/ELVA control and hydraulic camshaft replacement.
9420.0 kW
Power
Engine Specifications
6
Cylinders
400 mm
Bore
1600 mm
Stroke
9,420 kW
MCR Power
146.0 rpm
MCR RPM
2-stroke
Stroke Type
Family: MAN Energy Solutions ME/ME-C
· Tier: Tier III
· Fuel: HFO, VLSFO, MDO
Inspector Detail
✓ verified
▸
Designation decoded
6 = Zylinderzahl, S = Super Long Stroke, 40 = Bohrung 400 mm, ME-C = MAN Electronically controlled Mark C, 9.6 = Mark 9.6 Steuerungsgeneration.
Background
Die 6S40ME-C erweitert die 5-Zylinder-S40 um einen Zylinder fuer besseren Massenausgleich und ca. 20% mehr Leistung. Typisch fuer kleine Bulker, Feeder-Container und General-Cargo-Schiffe. Die S-Variante (1600mm Hub) bietet hoehere Drehzahl als die G-Variante.
Calculated metrics
Stroke To Bore Ratio
4.0
Inspector checklist
Kraftstoffsystem
- Kraftstoffpumpen: Plunger, Duesen-Oeffnungsdruck, Spray-Pattern
- Vorwaermung: 12-15 cSt bei HFO
- Cat-Fines: Separator <15 ppm
- VLSFO-Kompatibilitaet: Stabilitaet, Asphaltene
Laufzeug und Tribologie
- Laufbuchsen 400mm: Liner-Wear-Rate, BN-Abstimmung auf Schwefelgehalt, Honmuster
- Kolbenringe: Gap-Messung, Laufflaechenzustand
- Kreuzkopf: S/B=4.0, moderate Seitenkraefte, LI-Aufnahme
- Stopfbuchse: Drainage-Mengen loggen
ME-Steuerung
- HPS 300 bar: Oelqualitaet ISO 4406, Filter-dP
- FIVA: Timing, Kalibrierung Mark 9.6
- CCU: Software-Version, Alarme
Turbolader
- Lagerspiel, Vibration, Reinigung Wasser-Wash
- Spuelluftdruck bei verschiedenen Lasten
Logbook reference values
| Parameter | Expected | Deviation means |
|---|---|---|
| Abgastemperatur | 320-420 Grad C | >25 Grad C Spread: Injektor/Timing |
| Spuelluftdruck | 1.5-3.0 bar | Niedrig: TC-Fouling |
| Zylindeloelverbrauch | 0.7-1.2 g/kWh | BN an Schwefel anpassen |
| OMD | <2.5% LEL | Stopfbuchse pruefen |
Common Failure Modes
Cat-Fine-Schaeden
Symptoms: Beschleunigter Liner-Wear, metallischer Abrieb
Causes: Separator ineffizient, VLSFO-Qualitaet
Preventive: Cat-Fines <15 ppm nach Separator.
Cold Corrosion
Symptoms: Hoher Liner-Wear, Cloverleafing
Causes: BN zu niedrig, Teillast
Preventive: BN anpassen, Feed-Rate bei Teillast erhoehen.
FIVA-Fehlfunktion
Symptoms: Timing-Abweichung, Pmax-Spread
Causes: Oelkontamination, Ventilsitz
Preventive: HPS-Oel pruefen, FIVA alle 16000-24000 Bh.
Expert tips
- 💡 6 Zylinder bieten deutlich besseren Massenausgleich als 5 — weniger Vibrationsprobleme bei Slow Steaming.
- 💡 Kleiner Motor (400mm) mit guter Zugaenglichkeit — Scavenging-Port-Inspektion fuer alle 6 Zylinder regelmaessig nutzen.
- 💡 Bei kleinen Schiffen oft Tramping-Betrieb mit wechselnder Bunker-Qualitaet — Kraftstoff-Aufbereitung priorisieren.
Related components
Turbolader
Spuelluftkuehler
Separatoren
Alpha Lubricator (6 Einheiten)
HPS
Classification & regulatory
IMO Tier II. ECA: VLSFO (<0.5% S) oder Scrubber.
Reference content for inspector orientation. Always verify against manufacturer's manual, latest service letters and class society requirements.
Other Cylinder Configurations 50
5G40ME-C9.6
5 cyl
· 8,550 kW
5G45ME-C9.6
5 cyl
· 11,250 kW
5G50ME-C9.6
5 cyl
· 15,500 kW
5G60ME-C9.6
5 cyl
· 24,500 kW
5G65ME-C9.6
5 cyl
· 29,350 kW
5G70ME-C9.6
5 cyl
· 34,350 kW
5G80ME-C9.6
5 cyl
· 44,500 kW
5G90ME-C9.6
5 cyl
· 56,000 kW
5G95ME-C9.6
5 cyl
· 63,500 kW
5S40ME-C9.6
5 cyl
· 7,850 kW
5S46ME-C9.6
5 cyl
· 15,500 kW
5S50ME-C9.6
5 cyl
· 18,650 kW
5S60ME-C9.6
5 cyl
· 28,250 kW
5S65ME-C9.6
5 cyl
· 35,000 kW
5S70ME-C9.6
5 cyl
· 40,400 kW
5S80ME-C9.6
5 cyl
· 51,000 kW
5S90ME-C9.6
5 cyl
· 64,350 kW
5S95ME-C9.6
5 cyl
· 71,000 kW
6G40ME-C9.6
6 cyl
· 10,260 kW
6G45ME-C9.6
6 cyl
· 13,500 kW
6G50ME-C9.6
6 cyl
· 18,600 kW
6G60ME-C9.6
6 cyl
· 29,400 kW
6G65ME-C9.6
6 cyl
· 35,220 kW
6G70ME-C9.5
6 cyl
· 20,520 kW
6G70ME-C9.6
6 cyl
· 41,220 kW
6G80ME-C9.6
6 cyl
· 53,400 kW
6G90ME-C9.6
6 cyl
· 67,200 kW
6G95ME-C9.6
6 cyl
· 76,200 kW
6S46ME-C9.6
6 cyl
· 18,600 kW
6S50ME-C8.5
6 cyl
· 10,680 kW
6S50ME-C9.6
6 cyl
· 22,380 kW
6S60ME-C9.6
6 cyl
· 33,900 kW
6S65ME-C9.6
6 cyl
· 42,000 kW
6S70ME-C8.5
6 cyl
· 18,660 kW
6S70ME-C9.6
6 cyl
· 48,480 kW
6S80ME-C9.5
6 cyl
· 24,000 kW
6S80ME-C9.6
6 cyl
· 61,200 kW
6S90ME-C9.6
6 cyl
· 77,220 kW
6S95ME-C9.6
6 cyl
· 85,200 kW
7G40ME-C9.6
7 cyl
· 11,970 kW
7G45ME-C9.6
7 cyl
· 15,750 kW
7G50ME-C9.6
7 cyl
· 21,700 kW
7G60ME-C9.6
7 cyl
· 34,300 kW
7G65ME-C9.6
7 cyl
· 41,090 kW
7G70ME-C9.6
7 cyl
· 48,090 kW
7G80ME-C9.5
7 cyl
· 34,930 kW
7G80ME-C9.6
7 cyl
· 62,300 kW
7G90ME-C9.6
7 cyl
· 78,400 kW
7G95ME-C9.5
7 cyl
· 46,550 kW
7G95ME-C9.6
7 cyl
· 88,900 kW
Components & Design
Alpha Lubricator Control
MAN Energy Solutions
MAN Alpha Lubricator Mk III
Feed rate 0.6-1.2 g/kWh depending on fuel sulfur. Monitor via Alpha ACC (Adaptive Cylinder lubrication Control).
Lead time: 6 wk
25.0 kg
Crankcase Oil Mist Detector
Schaller Automation
Schaller Visatron VN215+ OMD
SOLAS mandatory. Test weekly. Clean sensor optics every 4,000 hrs. Replace reference cell every 2 years.
Lead time: 2 wk
8.0 kg
Crosshead Bearing
MAN Energy Solutions
MAN Crosshead Bearing (thin-shell, white metal)
Inspect at 16,000 hrs. Check bearing clearance. Monitor via bearing temperature and oil analysis.
Lead time: 12 wk
380.0 kg
Cylinder Liner
MAN Energy Solutions
MAN ME-C Cylinder Liner (bore-cooled)
Wear monitoring via calibration. Max wear 0.8% of bore. Replace typically at 32,000-60,000 hrs.
Lead time: 16 wk
3500.0 kg
Engine Control Unit (ECU / ECS)
MAN Energy Solutions
MAN ECS (Engine Control System)
Dual-redundant ECU. Software updates via MAN PrimeServ. Keep backup CCU on board.
Lead time: 8 wk
45.0 kg
Exhaust Valve (& Valve Seat)
MAN Energy Solutions
MAN Exhaust Valve (Nimonic/Stellite)
Overhaul at 8,000-12,000 hrs. Stellite-faced seat. Grinding/lapping at overhaul. Check spindle guide clearance.
Lead time: 8 wk
320.0 kg
FIVA Valve (ME-type)
MAN Energy Solutions
MAN FIVA Valve (ME-C)
FIVA = Fuel Injection Valve Actuator. Overhaul at 8,000 hrs. Critical for timing accuracy.
Lead time: 8 wk
35.0 kg
Fuel Booster Module (ME-type)
MAN Energy Solutions
MAN Fuel Booster Module
Overhaul at 16,000 hrs. Pressure test fuel pipes. Check plunger wear with micrometer.
Lead time: 12 wk
450.0 kg
Fuel Valve (Injector)
MAN Energy Solutions
MAN ME-C Fuel Valve Assembly
Overhaul every 4,000-8,000 hrs. Pressure test after overhaul. Nozzle replacement at 8,000 hrs.
Lead time: 4 wk
85.0 kg
Governor (Electronic/Woodward)
Woodward
Woodward 723PLUS Digital Governor
Electronic governor integrated with ECS on ME engines. Firmware updates via Woodward service.
Lead time: 4 wk
15.0 kg
Hydraulic Cylinder Unit (HCU)
MAN Energy Solutions
MAN HCU (ME-C type, per cylinder)
One HCU per cylinder. FIVA valve overhaul at 8,000 hrs. Booster overhaul at 16,000 hrs.
Lead time: 12 wk
1200.0 kg
Hydraulic Power Supply (HPS)
MAN Energy Solutions
MAN HPS Unit (ME-C)
Servo oil SAE 30 / System oil. Filter change every 4000 hrs. Monitor servo oil pressure.
Lead time: 16 wk
2800.0 kg
Main Bearings
MAN Energy Solutions
MAN Main Bearing Shells (white metal/tri-metal)
Inspect at 16,000 hrs. Jack up crankshaft for clearance measurement. Replace at signs of overlay fatigue.
Lead time: 8 wk
250.0 kg
PMI (Pressure Measurement Indicator)
MAN Energy Solutions
MAN PMI Sensor System
Online cylinder pressure monitoring. Calibrate sensors annually. Essential for combustion optimization.
Lead time: 4 wk
5.0 kg
Piston Crown
MAN Energy Solutions
MAN ME-C Piston Crown (bore-cooled Cr-Mo steel)
Inspect at 16,000 hrs. Pull piston at 16,000-24,000 hrs. Check cooling bores with borescope.
Lead time: 16 wk
1800.0 kg
Piston Ring Pack
MAN Energy Solutions
MAN Piston Ring Set (CPR / AL rings)
CPR (Controlled Pressure Relief) top ring. Replace at 8,000-16,000 hrs depending on wear.
Lead time: 4 wk
60.0 kg
Scavenge Air Cooler
MAN Energy Solutions
MAN Scavenge Air Cooler (plate-type)
Clean air side every 4,000-8,000 hrs (chemical/HP water). Monitor pressure drop and charge air temp.
Lead time: 16 wk
5500.0 kg
Turbocharger Unit (ABB/MHI/Napier)
ABB Turbocharging
ABB A175-L Turbocharger
Overhaul at 12,000-16,000 hrs. Water washing every 24-100 hrs depending on load.
Lead time: 12 wk
4500.0 kg
Technical Data
unified from engine model
True
🤖 Ask about this model
One free question — answered like a marine engineer. No account needed.
Suppliers & Spare Parts
Direct links to manufacturer, datasheet, spare-parts portal and dealers — request access below.
📄 Request sourcing links & documents🛠 Manage this equipment in your fleet
Cases, daily reports, timesheets and AI troubleshooting in the OceanSphere Marine app — free for 14 days.
Start free trial →🔎 Suppliers & service for this equipment
Find manufacturers, repair shops and spare-part dealers in the Maritime Network — our global company directory.
Maritime Network →Manuals
-
operating
MAN B&W ME/ME-C/ME-B Engine Operation (OM-ME-C)
-
maintenance
MAN B&W ME/ME-C Maintenance Manual (MM-ME-C)
-
spare_parts
MAN B&W ME/ME-C Illustrated Parts Catalogue (IPC-ME-C)
-
service_letter
SL-ME Service Letters Collection (SL-ME)
- technical_data
Working on this unit?
Log hours, photos and findings into an invoice-ready service report — OceanSphere Marine, 14-day free trial.
Need a service partner for MAN Energy Solutions?
114,000+ shipyards, suppliers and service companies in the Maritime Network directory.
Equipment Model #38461
· ✓ still in production