Cargo Securing Equipment
Cargo securing equipment holds twist locks, lashing rods, turnbuckles and bridge fittings that lock containers or general cargo to the deck and to each other, converting stack weight into forces the ship's structure can actually absorb. On a container ship, it decides whether the top tier survives a beam sea.
What to check on a Cargo Securing Equipment.
10 models from MacGregor in Cargo Securing Equipment. Below: the full model list.
What sets cargo securing equipment apart
Cargo securing equipment does one job: turn a stack of boxes or a piece of break-bulk cargo into a load path the ship's structure can absorb. Unlike lashing bridges or fixed pedestals, which are part of the hull structure, this is the loose and semi-permanent gear a stevedore or crew member fits by hand for each voyage — twist locks, lashing rods, turnbuckles, D-rings, wire lashings and chain binders. The engineering behind it is simple statics, but the consequences of getting it wrong are not: a container that breaks loose in a seaway can take out the row next to it before anyone on the bridge notices the stack angle has changed.
Legend
- twist lock at corner casting
- containers on deck
- bridge fitting
- turnbuckle
- lashing rod
- deck socket
Main components
Twist locks
Semi-automatic or fully automatic twist locks engage the corner castings of adjacent containers and resist vertical separation. Semi-automatic types need a lashing gang to manually rotate the handle closed; fully automatic types lock on contact when the crane lands the box and release with a lanyard from deck level, which is standard on modern container tonnage to cut the time gangs spend between bays.
Lashing rods and turnbuckles
Rods run diagonally from the corner casting down to a foundation socket or lashing bridge, tensioned by a turnbuckle. Rod length is matched to bay and tier — a rod cut for tier 2 will not tension correctly at tier 4, so rod sets are colour-coded or numbered by most operators to stop the wrong length going on in the dark.
Read the full guide
Lashing bridges and D-rings
Fixed steel bridges between bays give lashers a working platform and a mid-height securing point, halving the effective span a rod has to cover. On general cargo and ro-ro tonnage, deck-welded D-rings and pad eyes serve the same role for chain or wire lashings over machinery, vehicles or project cargo.
Selection and sizing
Securing arrangements are calculated, not guessed, using the vessel's approved Cargo Securing Manual (CSM). The variables that drive the calculation are stack weight, stack height, GM and roll period, expected wind and sea state for the trade, and the maximum permissible lashing force (MSL) of each component. Key figures a purchaser checks before ordering replacement gear:
- Break load and MSL stamped on the rod or twist lock — MSL is typically 50% of break load
- Corrosion allowance built into wire diameter for open-deck exposure
- Corner casting type the twist lock is rated for
- Rod thread standard — mixing metric and imperial turnbuckle threads on one bay is a recurring yard error
Regulations and class
The Cargo Securing Manual is required under SOLAS Ch. VI/VII and must be approved by the flag state or a recognised organisation before it is used on board. It specifies the exact type, quantity and MSL of securing gear for every stowage position, and replacement gear has to match what the CSM lists or the arrangement needs re-approval. The IMO/ILO/UNECE Guidelines for Packing of Cargo Transport Units cover securing inside the box itself, a separate responsibility chain from deck securing that often gets confused with it during cargo claims.
Typical faults
| Fault | Consequence |
|---|---|
| Worn or bent twist lock cones | Lock does not fully engage, container can lift under roll |
| Corroded or kinked lashing wire | Reduced break load, sudden failure without warning |
| Wrong rod length used at a tier | Rod cannot reach correct tension angle, lashing effectively slack |
| Turnbuckle threads seized from salt exposure | Gang cannot tension the lashing, position left under-tensioned |
What to look for in a supplier
- Certificates of test for break load and MSL traceable to a batch, not just a type approval
- Stock matched to the corner casting types actually fitted on the trading containers
- Galvanising or coating specification suited to the trade — North Atlantic exposure eats plain steel fast
- Ability to supply a full CSM-matched set rather than mixed lengths that force the crew to improvise on deck
Count the gear back in after every discharge port — a lashing set quietly short three rods becomes the gang's problem at midnight in a swell, not the office's problem in daylight.
Models in this type.
The best-documented model of each manufacturer first, then the next — 10 of 10 models in Cargo Securing Equipment. Every row links to full specifications, documents and service notes.
Manufacturers.
All 7 manufacturers with models of Cargo Securing Equipment. Names with a manufacturer page open it; the others open a search across the full library.
All manufacturers in the libraryAlso in Cargo Hold Equipment.
The other equipment types in this category.
Inspection findings for this equipment
From public port state control and US Coast Guard records; OceanSphere assigns them to this equipment type from the descriptions.
Deficiency codes – USCG port state control – foreign-flag vessels
- 06104 · Lashing material – 9 findings
USCG components
- Lashing material – 25 findings, 2 with detention
Write to us about your machine — the answer comes by e-mail.
Name the make and the model and what the job is: a spare, a service call, a second opinion on a data sheet. We answer by e-mail.
No details at hand? A photo of the rating plate or the part is enough — simply attach it to the request.
Questions that come up with this equipment.
Is Cargo Securing Equipment data free?
Yes. Every model page, every guide and every datasheet for this type is readable without an account. An account adds saved searches and requests, nothing is taken away.
My model is missing — what now?
Send us the nameplate. We identify it by hand, add it to the library, and if you need a part or a service, the request is already on our desk.
Can you source a Cargo Securing Equipment part?
Yes. Tell us the manufacturer, the model and what you need — a person reads every request and replies by e-mail.