Purifier Feed/Discharge Pump
The feed pump meters oil into the purifier bowl at a fixed, low flow so retention time stays within the separator's design window; the discharge pump then draws clean oil off under a self-priming duty. Get either flow wrong and separation quality drops before anyone notices.
What to check on a Purifier Feed/Discharge Pump.
1 models from Alfa Laval in Purifier Feed/Discharge Pump. Below: the full model list.
What sets the feed and discharge pump apart
A disc-stack purifier only separates correctly if oil moves through the bowl at a steady, predictable rate. The feed pump exists purely to hold that rate constant: a low-capacity metering pump, usually a screw or internal-gear type, pushing preheated oil into the bowl at a flow set by the separator's throughput curve for the fuel or lube grade in use. The discharge pump does the opposite job at the other end - it pulls clean, treated oil out of the bowl outlet and pushes it on to the service or settling tank, working against whatever static lift and pipe resistance sits between the purifier and that tank. Neither pump does the separating; both control the conditions under which separation happens.
Legend
- Settling Tank
- Heater
- Service Tank
- Feed Pump (meters flow)
- Purifier Bowl
- Discharge Pump (self-priming)
- Sludge/water out
Main components
Feed pump
- Rotor or screw element sized for the target flow, often mounted on an extension of the same shaft that drives the bowl spindle, or as a small standalone unit with its own motor
- Mechanical seal or gland packing at the shaft penetration - this is the most common leak point on an older unit
- A relief valve or bypass line protecting the pump if the feed line is throttled or blocked downstream
- A metering or restriction valve, sometimes just a calibrated orifice, used to fine-tune actual flow against the manufacturer's capacity table
Discharge pump
- Self-priming positive displacement element, because a hermetic bowl discharges under a slight vacuum and the pump must draw reliably without air-locking
- Spring-loaded non-return valve at the outlet, stopping oil in the discharge line from running back into the bowl once the purifier stops
- Pressure gauge or transmitter connection feeding the purifier control panel, which normally trips the unit on sustained low discharge pressure
- On many modern skids, a solenoid-interlocked start sequence so the discharge pump only runs once the bowl has reached operating speed
Selection and sizing
Feed pump capacity has to match the separator's actual throughput at the viscosity and temperature the oil is running at, not the nominal maximum capacity printed on the nameplate. That nameplate figure usually applies to light diesel oil at a specific reference viscosity; heavy fuel or degraded lube oil needs a lower feed rate to keep retention time in the bowl long enough for water and solids to migrate to the periphery. Discharge pump sizing is a head calculation: static lift to the service tank plus line losses, checked against the pump curve at the viscosity expected in service.
| Parameter | Feed pump | Discharge pump |
|---|---|---|
| Duty | Constant low flow into bowl | Variable flow against system head |
| Priming | Flooded suction, rarely an issue | Must self-prime against vacuum |
| Failure symptom | Poor separation, water carry-over | Low discharge pressure trip |
Typical faults
- Worn screw or gear elements on the feed pump reduce delivered flow below the setpoint, shortening retention time and letting water pass into the clean oil outlet
- Seal wear at the feed pump shaft lets air into the suction side, causing an unstable feed rate and intermittent low-pressure alarms
- A discharge pump that loses prime after a stop-start cycle will not re-establish flow on its own, and the purifier control system reads this as a genuine low-pressure fault and shuts the unit down
- A stuck or worn non-return valve on the discharge line allows backflow into the bowl during shutdown, which can pull water back into oil that was already clean
What to look for in a supplier
- Match to the purifier OEM's own part number rather than a generic pump of similar flow and head - Alfa Laval, Mitsubishi Kakoki and GEA/Westfalia all pair pumps closely to bowl retention-time requirements
- Wetted-part material suited to the duty: stainless trim for lube oil with detergent additives, standard bronze or cast iron acceptable for straight fuel duty
- Seal material rated for the oil temperature actually seen at the purifier inlet, typically 85-98 degrees C for HFO purification
- Availability of just the wear kit (rotor, seal, valve) rather than a full pump exchange, since most failures are wear-part failures
If a purifier trips on low discharge pressure right after a routine stop, check whether the discharge pump has actually re-primed before chasing a control system fault - it is the more common cause.
Models in this type.
The best-documented model of each manufacturer first, then the next — 1 of 1 models in Purifier Feed/Discharge Pump. Every row links to full specifications, documents and service notes.
Manufacturers.
All 2 manufacturers with models of Purifier Feed/Discharge Pump. Names with a manufacturer page open it; the others open a search across the full library.
All manufacturers in the libraryAlso in Purifier Accessories.
The other equipment types in this category.
Write to us about your machine — the answer comes by e-mail.
Name the make and the model and what the job is: a spare, a service call, a second opinion on a data sheet. We answer by e-mail.
No details at hand? A photo of the rating plate or the part is enough — simply attach it to the request.
Questions that come up with this equipment.
Is Purifier Feed/Discharge Pump data free?
Yes. Every model page, every guide and every datasheet for this type is readable without an account. An account adds saved searches and requests, nothing is taken away.
My model is missing — what now?
Send us the nameplate. We identify it by hand, add it to the library, and if you need a part or a service, the request is already on our desk.
Can you source a Purifier Feed/Discharge Pump part?
Yes. Tell us the manufacturer, the model and what you need — a person reads every request and replies by e-mail.