OceanSphereENGINES
Library› Engine Room› Turbochargers› Turbocharger› Kompressorenbau Bannewitz ST7
Kompressorenbau Bannewitz

ST7

Turbocharger · Turbochargers

Technical data from manufacturer or class sources · not yet verified by a person​​‍‌​​‍‌‌​‌‍⁠⁠‌‍‌​⁠‌
Per manufacturer datasheetCapacity
Exhaust gas / charge airMedium

This is a turbocharger designed for use in marine and stationary applications. Kompressorenbau Bannewitz manufactures the ST7 model, which is intended for exhaust gas and charge air handling. The ST7 is suitable for 4-stroke marine and stationary diesel engines. Potential issues with this model include turbine-side fouling, compressor wheel fouling, bearing wear, and rotor vibration. Larger units in the ST series may require execution-specific rotor and casing parts. Servicing should be conducted in accordance with the manufacturer's manual and the requirements of any relevant classification society. Annual inspections are recommended at class survey intervals. Keeping a stock of spare parts as specified by the manufacturer is also advised.

Specifications

Technical data.

Do you have the manufacturer datasheet for this model? Send it with the enquiry form — we check it and name the source.

Engine Type4-stroke
Service

Service notes.

What our service work and the manufacturer documentation say about keeping this model running.

Servicing per the manufacturer's manual and classification society requirements. Annual inspection at class survey. Stock spare parts as specified by the manufacturer.

Inspection

Common failures & inspection points

Inspection

Inspector Detail

Common issues

  • Turbine-side fouling (carbon deposits, especially with heavy fuel oil)
  • Compressor wheel fouling (dust, oil mist, salt deposits)
  • Bearing wear (radial and axial play exceeding limits)
  • Rotor vibration (due to unbalance, bearing wear, or foreign object damage)
  • Oil leakage from bearing casings or oil supply/drain lines
  • Exhaust gas leakage from turbine casing joints or expansion bellows
  • Air filter clogging, leading to reduced compressor efficiency
  • Nozzle ring distortion or damage

Inspection checklist

  • Check for oil leaks around bearing housings, oil supply, and drain lines.
  • Inspect for exhaust gas leaks from turbine casing joints, expansion bellows, and gas outlet.
  • Verify condition of air filter element; clean or replace as necessary.
  • Check rotor axial and radial play (if inspection ports allow or during scheduled opening). Typical new values: Axial 0.08-0.15mm, Radial 0.15-0.30mm. Wear limits are usually +50% of new.
  • Visually inspect turbine and compressor wheels for fouling, erosion, or foreign object damage (FOD) through inspection ports.
  • Monitor bearing temperatures (via installed sensors or IR gun) for abnormal readings.
  • Listen for unusual noises (whining, grinding, rubbing) during operation.
  • Verify boost pressure and exhaust gas temperatures are within engine manufacturer's specified limits.
  • Check condition of water washing nozzles (if fitted) and ensure proper operation.
  • Inspect turbocharger mounting bolts and foundations for security and signs of cracking.

Service intervals

Air filter inspection/cleaningEvery 500-1000 running hours or as per manufacturer's recommendation.
Compressor/Turbine water washingEvery 250-500 running hours (depending on fuel quality and engine load).
Bearing inspection/replacement8,000 - 16,000 running hours (depending on bearing type and operating conditions).
Rotor cleaning and balancing12,000 - 24,000 running hours or as required by condition.
Major overhaul (full disassembly, inspection, replacement of worn parts)16,000 - 24,000 running hours or every 3-5 years, whichever comes first.
Annual InspectionRequired for Class Survey.

Typical intervals for this design class, not the manufacturer’s figures for your model. The manufacturer’s manual is binding.

Typical wear limits

Bearing Radial ClearanceNew: 0.15 - 0.30 mm. Wear Limit: +50% of new value or specific KBB value (e.g., 0.45 mm).
Bearing Axial Clearance (Thrust Bearing)New: 0.08 - 0.15 mm. Wear Limit: +50% of new value or specific KBB value (e.g., 0.25 mm).
Rotor UnbalanceChecked during overhaul; specific limits provided by KBB, typically < 10 g.mm for this size.
Blade Tip Clearance (Compressor/Turbine)Visual inspection for rubbing marks. Specific KBB values for new clearance (e.g., 0.5-1.0 mm), wear limit if rubbing is evident.
Nozzle Ring GapVisual inspection for distortion or excessive erosion/corrosion. KBB provides specific measurement points and limits.

Ranges are typical for this design class. Always confirm against the manufacturer documentation for your serial number.

Critical spares

  • Complete bearing cartridge sets (thrust and journal bearings)
  • Gasket and O-ring sets for casings and oil lines
  • Oil filter elements (if external oil filtration is used)
  • Air filter elements
  • Nozzle ring (if prone to wear/fouling in specific applications)
  • Impeller/Compressor wheel (for major damage, not routine replacement)
  • Turbine wheel (for major damage, not routine replacement)
  • High-temperature bolts and nuts for casing joints

Safety

  • High surface temperatures (up to 400-600°C on turbine casing) causing severe burn hazards.
  • High-speed rotating components (up to 30,000-50,000 RPM) posing severe injury risk during inspection or maintenance if not properly isolated and cooled.
  • Pressurized exhaust gas and charge air lines (up to 4-5 bar) presenting blow-out risk during disassembly.
  • Noise levels exceeding 100 dB, requiring hearing protection in the vicinity.
  • Hot oil and exhaust gas during disassembly and handling of components.

Class survey

The class surveyor will typically verify that maintenance records (logbook entries, service reports, spare parts consumption) are up-to-date and reflect manufacturer's recommendations and class requirements. A visual inspection for external leaks (oil, exhaust gas), excessive vibration, and general cleanliness will be performed. If the turbocharger has been opened for scheduled maintenance, the surveyor may require witnessing reassembly, bearing clearance checks, and rotor balancing certificates. Confirmation of critical spare parts availability onboard is also a common check. The surveyor will ensure that any safety devices, such as overspeed trips (if fitted and part of the engine's safety system), are in satisfactory condition.

Estimated lifetime: 16,000 - 24,000 running hours before major overhaul (e.g., full rotor reconditioning/replacement, bearing replacement, casing inspection). With proper maintenance, total service life can exceed 80,000 hours.

Spares

Replacement Parts

Spare parts notes

Larger ST-series units need execution-specific rotor and casing parts.

Need this part?

Request a quote for this model.

Free of charge — send us your request for Kompressorenbau Bannewitz equipment. Our team checks it and replies by e-mail.

For marine equipment hardly any maker or authorised dealer will name a price while the vessel is unknown. With the vessel details, availability and price can be settled faster; without them we may have to ask first, which costs a few days. If you are not allowed to name the vessel, a photo of the rating plate is enough — attach it below or send it as a reply to our confirmation e-mail.

Your contact details are not published. No account required.
Related models

Also in Turbocharger.

Other models of the same equipment type, Kompressorenbau Bannewitz first.

By manufacturer ABBMAN Energy SolutionsIHIMitsubishiABB Turbocharging / AccelleronKawasakiPBSTCummins Holset TurbochargersNapierMAN ES TurbochargingMitsubishi METGarrett Motion MarineVolvo Pentaengine.od / Other TurbochargersKBB TurboAll manufacturersSpare parts by equipmentNew here? Create a free account Can't read the plate? Try the nameplate scanner More like ST7
More than the data sheet shows

We answer by e-mail, never with an automatic reply.

Tell us what you need for this Kompressorenbau Bannewitz ST7 — a part, a service call, a second opinion. Are you Kompressorenbau Bannewitz? Claim this brand page.

Service engineer? Write the day report for this ST7 in OceanSphere Work — photos, hours and parts, as a PDF for the owner. Try it free for 14 days →

Frequently asked

Questions that come up with this equipment.

Is this model's data free?

Yes. Specifications, documents and service notes for this model are readable without an account. An account adds saved searches and requests, nothing is taken away.

Can you find a part for this exact model?

Yes. Tell us the manufacturer, the model and what you need — a person reads every request and replies by e-mail.

The specifications look wrong — what now?

Send us the nameplate or the correct value. We check it against the manufacturer datasheet or class-society record and update the page.