OceanSphereENGINES
Library› Engine Room› Air Compressors› Air Compressor› Burckhardt Compression 5LP250V
Burckhardt Compression

5LP250V

Air Compressor · Air Compressors

Technical data from manufacturer or class sources · not yet verified by a person​‍‌​‍‌⁠⁠​‌‍​‍​⁠‍​‍⁠‍
11.5 x 7 x 5.5Dimensions

Burckhardt Compression 5LP250V — Marine LNG fuel gas compression for ME-GI propulsion on LNG carriers.

Specifications

Technical data.reference — unverified

Do you have the manufacturer datasheet for this model? Send it with the enquiry form — we check it and name the source.

Rated Power1,950 kW
Mass Flow5,000 kg/h (at +20°C inlet)
Discharge Pressure300 bar
Cryogenic Design Temperature-160°C (Stage 1)
Dimensions11.5 × 7 × 5.5 m
Reliability98% product availability documented
Typical mass flow5'000 kg/h
Dimensions11.5 x 7 x 5.5 m
Inspection

Inspector Detail

Common issues

  • Labyrinth piston ring wear increasing internal leakage over running hours on the oil-free labyrinth stages
  • Packing/rod seal leakage on the ring-sealed stages, allowing gas to migrate toward the crankcase or vent system
  • Suction/discharge valve plate wear or breakage from high cycling rates
  • Distance piece purge/vent blockage or nitrogen supply failure, risking gas migration past the crankcase
  • Thermal cycling stress on cold-end components exposed to cryogenic suction temperatures
  • Vibration or pulsation issues in high-pressure discharge piping
  • Instrumentation (gas detection, pressure/temperature transmitters) drift affecting ESD trip reliability
  • Lubrication system contamination or degradation affecting crosshead/crankshaft bearings

Inspection checklist

  • Check distance piece nitrogen purge flow and pressure are within design range before and during running
  • Monitor and trend rod drop/vibration on each throw
  • Verify gas detection in the compressor house and distance piece vent lines is functioning and calibrated
  • Inspect suction/discharge valves at scheduled intervals for plate wear, spring condition and seat damage
  • Check packing case leak-off rate against the established baseline
  • Verify ESD (emergency shutdown) function test, including high/low pressure, high temperature and gas detection trips
  • Inspect crosshead guide and running gear lube oil condition and filter differential pressure
  • Check insulation/cladding on cryogenic suction lines for condensation, icing or damage
  • Verify safety/relief valve set pressures and test dates are current
  • Confirm compressor house ventilation rate meets the gas-safe area classification requirement

Service intervals

Nitrogen purge system checkeach start-up, plus continuous monitoring while running
Valve inspection (suction/discharge)per the maker's running-hour or cycle-count schedule - confirm against the maker's manual
Packing/rod seal leak-off monitoringcontinuous with logged trend; physical inspection at scheduled overhaul
ESD and gas detection function testper SOLAS/class requirement, commonly every 12 months plus each pre-use voyage check
Lube oil analysisevery 500 hours, or per the maker's schedule

Typical intervals for this design class, not the manufacturer’s figures for your model. The manufacturer’s manual is binding.

Critical spares

  • Suction and discharge valve assemblies per stage
  • Packing/rod seal sets for the ring-sealed stages
  • Labyrinth piston rings for the labyrinth-sealed stages
  • Distance piece purge components (orifices, check valves)
  • Crosshead/main bearing shells
  • Gas and vibration monitoring sensors

Safety

  • This compressor handles flammable natural gas at pressures up to around 300 bar - any leak in the compressor house is a major fire/explosion hazard, so gas detection and ESD systems must remain intact at all times
  • Cryogenic suction conditions (down to around -160 degC) present cold-burn and material embrittlement risk if insulation or design temperature limits are exceeded
  • Nitrogen purge/inert gas systems present an asphyxiation risk in confined distance piece or compressor house spaces if purge lines leak
  • High-pressure discharge piping stores significant energy - never work on pressurized sections without verified isolation and venting

Class survey

Gas fuel compressors serving ME-GI or similar dual-fuel propulsion are safety-critical items under the vessel's gas fuel system notation; surveys typically focus on ESD and gas detection function tests, purge/inert gas system integrity, valve and packing maintenance records, and pressure relief valve certification rather than internal inspection at every survey.

Need this part?

Request a quote for this model.

Free of charge — send us your request for Burckhardt Compression equipment. Our team checks it and replies by e-mail.

For marine equipment hardly any maker or authorised dealer will name a price while the vessel is unknown. With the vessel details, availability and price can be settled faster; without them we may have to ask first, which costs a few days. If you are not allowed to name the vessel, a photo of the rating plate is enough — attach it below or send it as a reply to our confirmation e-mail.

Your contact details are not published. No account required.
Related models

Also in Air Compressor.

Other models of the same equipment type, Burckhardt Compression first.

By manufacturer QuincySperreTamrotor Marine Compressors (TMC)HatlapaAtlas Copco MarineBauerTanabeHamworthyCorkenSauer CompressorsBurckhardt CompressionGardner DenverDeno CompressorsKasco MarineBelliss & MorcomAll manufacturersSpare parts by equipmentNew here? Create a free account Can't read the plate? Try the nameplate scanner More like 5LP250V
More than the data sheet shows

We answer by e-mail, never with an automatic reply.

Tell us what you need for this Burckhardt Compression 5LP250V — a part, a service call, a second opinion. Are you Burckhardt Compression? Claim this brand page.

Service engineer? Write the day report for this 5LP250V in OceanSphere Work — photos, hours and parts, as a PDF for the owner. Try it free for 14 days →

Frequently asked

Questions that come up with this equipment.

Is this model's data free?

Yes. Specifications, documents and service notes for this model are readable without an account. An account adds saved searches and requests, nothing is taken away.

Can you find a part for this exact model?

Yes. Tell us the manufacturer, the model and what you need — a person reads every request and replies by e-mail.

The specifications look wrong — what now?

Send us the nameplate or the correct value. We check it against the manufacturer datasheet or class-society record and update the page.