OceanSphereENGINES

6L6AYAM

Auxiliary Engine (Generator Set) · Auxiliary Engines

Technical data from manufacturer or class sources · not yet verified by a person​‍​⁠​‌‌​⁠‍‍‌‍‍‍‍‌​‌‌
1,290 kWPower
6Cylinders
220 mmBore
320 mmStroke

Yanmar Marine 6L6AYAM — Common Rail, 6 cyl × 220mm bore, 1500 rpm, HFO/MGO, 1290 kW.

Specifications

Technical data.reference — unverified

Do you have the manufacturer datasheet for this model? Send it with the enquiry form — we check it and name the source.

ConfigurationL
Speed (rpm)1500
Fuel TypeHFO/MGO
TechnologyCommon Rail
Power (kW)1290
Inspection

Inspector Detail ✓ verified

Common issues

  • Common Rail injector issues: Clogging, wear, leakage (internal or external), leading to poor combustion, increased exhaust temperatures, or fuel dilution of lube oil.
  • High-Pressure Fuel Pump (HPFP) wear: Reduced fuel pressure, internal leaks, or component failure due to HFO quality or lack of lubrication, impacting engine performance.
  • Cylinder liner wear and cold corrosion: Accelerated wear rates, especially when operating on HFO, if cylinder lubrication is inadequate or engine temperatures are too low.
  • Exhaust valve burning/corrosion: Due to high temperatures, poor fuel quality, or improper valve seating, leading to loss of compression and power.
  • Turbocharger fouling or bearing wear: Reduced efficiency, increased exhaust back pressure, or abnormal noise, often exacerbated by HFO operation.
  • Fuel system contamination: Sludge, water, or cat fines from HFO leading to filter blockages, pump wear, and injector damage.
  • Lube oil degradation/contamination: Fuel dilution, water ingress, or excessive soot loading, leading to accelerated engine wear if not monitored and addressed.
  • Cooling system blockages: Fouling of heat exchangers or internal passages, leading to overheating or reduced engine efficiency.

Inspection checklist

  • Engine room cleanliness and visual inspection for leaks (fuel, lube oil, cooling water, exhaust gas) around the engine, piping, and flanges.
  • Performance monitoring data review: Check exhaust gas temperatures (individual cylinders and turbocharger inlet/outlet), charge air pressure/temperature, lube oil pressure/temperature, cooling water pressure/temperature, fuel pressure, and engine load.
  • Fuel system integrity: Inspect fuel filters (pre-filters, main filters) for clogging, check fuel pressures, and verify proper operation of HFO/MGO changeover system.
  • Lube oil system: Check oil level, pressure, filter condition, and review recent lube oil analysis reports for signs of degradation or contamination.
  • Cooling system: Verify cooling water levels, pressures, and temperatures. Inspect heat exchangers for cleanliness and signs of leakage.
  • Turbocharger inspection: Check for abnormal noise, excessive bearing play (axial/radial), and cleanliness of compressor and turbine sides.
  • Common Rail system specific: Inspect high-pressure fuel lines for leaks, check injector leak-off rates (if measurable), and listen for abnormal HPFP noise.
  • Safety devices: Verify functionality of overspeed trip, low lube oil pressure shutdown, high cooling water temperature shutdown, and emergency stop.
  • Vibration and noise: Listen for abnormal engine noises (knocking, rattling) and check for excessive vibrations during operation.

Service intervals

Daily ChecksVisual inspection, fluid levels, gauge readings, filter drains.
250-500 hoursLube oil filter replacement, fuel filter element replacement.
1000-2000 hoursValve clearance check/adjustment, fuel injector inspection/overhaul (nozzle tips).
4000-6000 hoursCylinder head overhaul (valves, springs, seats), turbocharger overhaul (bearings, cleaning).
8000-12000 hoursPiston and connecting rod overhaul (rings, bearings), cylinder liner inspection/measurement.
24000-36000 hoursMajor overhaul (main bearings, crankshaft deflection check, full engine inspection).

Typical wear limits

Cylinder liner wearMax 0.6-0.8% of bore diameter (approx. 1.3-1.8 mm for 220mm bore) at the top ring reversal point.
Piston ring groove wearSpecific limits per groove, typically measured by feeler gauge between ring and groove side, exceeding manufacturer's specified clearance (e.g., 0.15-0.25 mm for top ring).
Crankshaft deflectionMax 0.05-0.10 mm across any web, depending on manufacturer's specific guidelines.
Connecting rod bearing clearanceMax 0.15-0.25 mm over new specified clearance.
Main bearing clearanceMax 0.20-0.30 mm over new specified clearance.
Exhaust valve seat recessionMax 0.5-1.0 mm from original position, requiring valve seat grinding or replacement.

Ranges are typical for this design class. Always confirm against the manufacturer documentation for your serial number.

Critical spares

  • Complete fuel injectors or nozzle tips (Common Rail specific)
  • Full set of fuel filter elements (main and pre-filters)
  • Full set of lube oil filter elements
  • Turbocharger bearing cartridge or repair kit
  • High-pressure fuel pump repair kit or spare elements (if modular)
  • Assorted O-rings, gaskets, and seals for common maintenance tasks
  • Engine speed sensor and common pressure/temperature sensors
  • Starter motor or solenoid repair kit

Safety

  • High-pressure fuel lines (Common Rail): Risk of fuel spray fires or skin penetration injuries due to pressures exceeding 2000 bar. Ensure all lines are properly secured and shielded.
  • Hot surfaces: Exhaust manifold, turbocharger, engine block, and associated piping operate at high temperatures, posing burn risks. Ensure adequate insulation and warning signs.
  • Rotating machinery: Exposed rotating parts (flywheel, coupling, fan belts) pose entanglement hazards. Ensure all guards are in place.
  • Electrical hazards: High voltage from the generator and control systems. Ensure proper lockout/tagout procedures are followed during maintenance.
  • Noise levels: Engine operation generates high noise levels, requiring hearing protection in the vicinity.

Class survey

A class surveyor will typically focus on the engine's overall condition, operational reliability, and compliance with regulatory standards. Key checks include: verification of maintenance records and running hours; operational demonstration (starting, stopping, load acceptance, governor response); testing of safety devices (overspeed trip, low lube oil pressure shutdown, high cooling water temperature shutdown, emergency stop); physical inspection for leaks, abnormal vibrations, foundation integrity, and exhaust system condition; integrity of high-pressure fuel lines and shielding; verification of fuel changeover procedures (HFO/MGO); and functionality of all alarms and monitoring systems. Lube oil analysis reports and fuel quality records will also be reviewed.

Estimated lifetime: 24,000 - 36,000 hours before major overhaul (e.g., pistons, liners, main/con-rod bearings), with total engine life often exceeding 80,000 hours with proper maintenance.

Need this part?

Request a quote for this model.

Free of charge — send us your request for Yanmar Marine equipment. Our team checks it and replies by e-mail.

For marine equipment hardly any maker or authorised dealer will name a price while the vessel is unknown. With the vessel details, availability and price can be settled faster; without them we may have to ask first, which costs a few days. If you are not allowed to name the vessel, a photo of the rating plate is enough — attach it below or send it as a reply to our confirmation e-mail.

Your contact details are not published. No account required.
Related models

Also in Auxiliary Engine (Generator Set).

Other models of the same equipment type, Yanmar Marine first.

By manufacturer CaterpillarMAN Energy SolutionsWärtsiläVolvo PentaScaniaMaK (Caterpillar)CumminsDeerePerkinsDaihatsuHanshinMTUYanmarBaudouinDeutzAll manufacturersSpare parts by equipmentNew here? Create a free account Can't read the plate? Try the nameplate scanner All Yanmar Marine models More like 6L6AYAM
More than the data sheet shows

We answer by e-mail, never with an automatic reply.

Tell us what you need for this Yanmar Marine 6L6AYAM — a part, a service call, a second opinion. Are you Yanmar Marine? Claim this brand page.

Service engineer? Write the day report for this 6L6AYAM in OceanSphere Work — photos, hours and parts, as a PDF for the owner. Try it free for 14 days →

Frequently asked

Questions that come up with this equipment.

Is this model's data free?

Yes. Specifications, documents and service notes for this model are readable without an account. An account adds saved searches and requests, nothing is taken away.

Can you find a part for this exact model?

Yes. Tell us the manufacturer, the model and what you need — a person reads every request and replies by e-mail.

The specifications look wrong — what now?

Send us the nameplate or the correct value. We check it against the manufacturer datasheet or class-society record and update the page.