OceanSphereENGINES

6L6AYAM

Silnik pomocniczy (zespół prądotwórczy) · Silniki pomocnicze

Dane techniczne ze źródeł producenta lub towarzystwa · jeszcze niesprawdzone ręcznie​‍​⁠​‌‌​⁠‍‍‌‍‍‍‍‌​‌‌
1 290 kWMoc
6Cylindry
220 mmŚrednica cylindra
320 mmSkok

Yanmar Marine 6L6AYAM — Common Rail, 6 cyl × 220mm bore, 1500 rpm, HFO/MGO, 1290 kW.

Dane techniczne

Dane techniczne.dane referencyjne — niezweryfikowane

Masz kartę katalogową producenta dla tego modelu? Wyślij ją razem z formularzem zapytania — sprawdzimy ją i podamy źródło.

KonfiguracjaL
Obroty (1/min)1500
Rodzaj paliwaHFO/MGO
TechnologiaCommon Rail
Moc (kW)1290
Inspekcja

Szczegóły inspektora ✓ zweryfikowane

Typowe problemy

  • Common Rail injector issues: Clogging, wear, leakage (internal or external), leading to poor combustion, increased exhaust temperatures, or fuel dilution of lube oil.
  • High-Pressure Fuel Pump (HPFP) wear: Reduced fuel pressure, internal leaks, or component failure due to HFO quality or lack of lubrication, impacting engine performance.
  • Cylinder liner wear and cold corrosion: Accelerated wear rates, especially when operating on HFO, if cylinder lubrication is inadequate or engine temperatures are too low.
  • Exhaust valve burning/corrosion: Due to high temperatures, poor fuel quality, or improper valve seating, leading to loss of compression and power.
  • Turbocharger fouling or bearing wear: Reduced efficiency, increased exhaust back pressure, or abnormal noise, often exacerbated by HFO operation.
  • Fuel system contamination: Sludge, water, or cat fines from HFO leading to filter blockages, pump wear, and injector damage.
  • Lube oil degradation/contamination: Fuel dilution, water ingress, or excessive soot loading, leading to accelerated engine wear if not monitored and addressed.
  • Cooling system blockages: Fouling of heat exchangers or internal passages, leading to overheating or reduced engine efficiency.

Lista kontrolna przeglądu

  • Engine room cleanliness and visual inspection for leaks (fuel, lube oil, cooling water, exhaust gas) around the engine, piping, and flanges.
  • Performance monitoring data review: Check exhaust gas temperatures (individual cylinders and turbocharger inlet/outlet), charge air pressure/temperature, lube oil pressure/temperature, cooling water pressure/temperature, fuel pressure, and engine load.
  • Fuel system integrity: Inspect fuel filters (pre-filters, main filters) for clogging, check fuel pressures, and verify proper operation of HFO/MGO changeover system.
  • Lube oil system: Check oil level, pressure, filter condition, and review recent lube oil analysis reports for signs of degradation or contamination.
  • Cooling system: Verify cooling water levels, pressures, and temperatures. Inspect heat exchangers for cleanliness and signs of leakage.
  • Turbocharger inspection: Check for abnormal noise, excessive bearing play (axial/radial), and cleanliness of compressor and turbine sides.
  • Common Rail system specific: Inspect high-pressure fuel lines for leaks, check injector leak-off rates (if measurable), and listen for abnormal HPFP noise.
  • Safety devices: Verify functionality of overspeed trip, low lube oil pressure shutdown, high cooling water temperature shutdown, and emergency stop.
  • Vibration and noise: Listen for abnormal engine noises (knocking, rattling) and check for excessive vibrations during operation.

Interwały serwisowe

Daily ChecksVisual inspection, fluid levels, gauge readings, filter drains.
250-500 hoursLube oil filter replacement, fuel filter element replacement.
1000-2000 hoursValve clearance check/adjustment, fuel injector inspection/overhaul (nozzle tips).
4000-6000 hoursCylinder head overhaul (valves, springs, seats), turbocharger overhaul (bearings, cleaning).
8000-12000 hoursPiston and connecting rod overhaul (rings, bearings), cylinder liner inspection/measurement.
24000-36000 hoursMajor overhaul (main bearings, crankshaft deflection check, full engine inspection).

Typowe granice zużycia

Cylinder liner wearMax 0.6-0.8% of bore diameter (approx. 1.3-1.8 mm for 220mm bore) at the top ring reversal point.
Piston ring groove wearSpecific limits per groove, typically measured by feeler gauge between ring and groove side, exceeding manufacturer's specified clearance (e.g., 0.15-0.25 mm for top ring).
Crankshaft deflectionMax 0.05-0.10 mm across any web, depending on manufacturer's specific guidelines.
Connecting rod bearing clearanceMax 0.15-0.25 mm over new specified clearance.
Main bearing clearanceMax 0.20-0.30 mm over new specified clearance.
Exhaust valve seat recessionMax 0.5-1.0 mm from original position, requiring valve seat grinding or replacement.

Zakresy są typowe dla tej klasy konstrukcyjnej. Decydujące są zawsze dokumenty producenta dla danego numeru seryjnego.

Krytyczne części zamienne

  • Complete fuel injectors or nozzle tips (Common Rail specific)
  • Full set of fuel filter elements (main and pre-filters)
  • Full set of lube oil filter elements
  • Turbocharger bearing cartridge or repair kit
  • High-pressure fuel pump repair kit or spare elements (if modular)
  • Assorted O-rings, gaskets, and seals for common maintenance tasks
  • Engine speed sensor and common pressure/temperature sensors
  • Starter motor or solenoid repair kit

Bezpieczeństwo

  • High-pressure fuel lines (Common Rail): Risk of fuel spray fires or skin penetration injuries due to pressures exceeding 2000 bar. Ensure all lines are properly secured and shielded.
  • Hot surfaces: Exhaust manifold, turbocharger, engine block, and associated piping operate at high temperatures, posing burn risks. Ensure adequate insulation and warning signs.
  • Rotating machinery: Exposed rotating parts (flywheel, coupling, fan belts) pose entanglement hazards. Ensure all guards are in place.
  • Electrical hazards: High voltage from the generator and control systems. Ensure proper lockout/tagout procedures are followed during maintenance.
  • Noise levels: Engine operation generates high noise levels, requiring hearing protection in the vicinity.

Przegląd klasyfikacyjny

A class surveyor will typically focus on the engine's overall condition, operational reliability, and compliance with regulatory standards. Key checks include: verification of maintenance records and running hours; operational demonstration (starting, stopping, load acceptance, governor response); testing of safety devices (overspeed trip, low lube oil pressure shutdown, high cooling water temperature shutdown, emergency stop); physical inspection for leaks, abnormal vibrations, foundation integrity, and exhaust system condition; integrity of high-pressure fuel lines and shielding; verification of fuel changeover procedures (HFO/MGO); and functionality of all alarms and monitoring systems. Lube oil analysis reports and fuel quality records will also be reviewed.

Szacowana trwałość: 24,000 - 36,000 hours before major overhaul (e.g., pistons, liners, main/con-rod bearings), with total engine life often exceeding 80,000 hours with proper maintenance.

Potrzebujesz tej części?

Zapytaj o ofertę na ten model.

Bezpłatnie — wyślij zapytanie dotyczące sprzętu Yanmar Marine. Nasz zespół je sprawdzi i odpowie e-mailem.

W przypadku sprzętu okrętowego prawie żaden producent ani autoryzowany dystrybutor nie podaje ceny, dopóki statek jest nieznany. Z danymi statku dostępność i cenę da się ustalić szybciej; bez nich być może musimy najpierw dopytać, co kosztuje kilka dni. Jeśli nie wolno Ci podać statku, wystarczy zdjęcie tabliczki znamionowej — dołącz je poniżej lub odeślij w odpowiedzi na nasz e-mail potwierdzający.

Twoje dane kontaktowe nie są publikowane. Konto nie jest wymagane.
Powiązane modeli

Także w Silnik pomocniczy (zespół prądotwórczy).

Inne modele tego samego typu sprzętu, najpierw Yanmar Marine.

Według producenta CaterpillarMAN Energy SolutionsWärtsiläVolvo PentaScaniaMaK (Caterpillar)CumminsDeerePerkinsDaihatsuHanshinMTUYanmarBaudouinDeutzWszyscy producenciCzęści według urządzeńNowy użytkownik? Załóż darmowe konto Nieczytelna tabliczka? Wypróbuj skaner tabliczek Wszystkie modele Yanmar Marine Podobne do 6L6AYAM
Więcej, niż pokazuje karta katalogowa

Odpowiadamy e-mailem, nigdy automatem.

Powiedz nam, czego potrzebujesz do tego Yanmar Marine 6L6AYAM — części, wizyty serwisowej, drugiej opinii. Czy jesteś Yanmar Marine? Przejmij tę stronę marki.

Serwisant? Napisz raport dzienny dla tego 6L6AYAM w OceanSphere Work — zdjęcia, godziny i części, jako PDF dla armatora. Wypróbuj 14 dni za darmo →

Często pytane

Pytania, które pojawiają się przy tym sprzęcie.

Czy dane tego modelu są bezpłatne?

Tak. Dane techniczne, dokumenty i uwagi serwisowe tego modelu są dostępne bez konta. Konto dodaje zapisane wyszukiwania i zapytania, niczego nie odbiera.

Czy znajdziecie część dokładnie do tego modelu?

Tak. Podaj producenta, model i czego potrzebujesz — każde zapytanie czyta człowiek i odpowiada e-mailem.

Dane techniczne wydają się błędne — co teraz?

Wyślij nam tabliczkę lub prawidłową wartość. Sprawdzimy ją w karcie danych producenta lub rejestrze towarzystwa klasyfikacyjnego i zaktualizujemy stronę.