OceanSphereENGINES
Library› Engine Room› Auxiliary Engines› Auxiliary Engine (Generator Set)› MTU Onsite Energy Series 1163 G-20cyl

Series 1163 G-20cyl

Auxiliary Engine (Generator Set) · Auxiliary Engines

Technical data from manufacturer or class sources · not yet verified by a person​‍​⁠​‌‌​​‍​⁠​‍​⁠⁠​‍​
5,800 kWPower
20Cylinders
230 mmBore
290 mmStroke

MTU Onsite Energy Series 1163 G-20cyl — Mechanical, 20 cyl × 230mm bore, 1300 rpm, MGO, 5800 kW.

Specifications

Technical data.reference — unverified

Do you have the manufacturer datasheet for this model? Send it with the enquiry form — we check it and name the source.

ConfigurationV
Speed (rpm)1300
Fuel TypeMGO
TechnologyMechanical
Power (kW)5800
Inspection

Inspector Detail ✓ verified

Common issues

  • Fuel injector nozzle wear or clogging, leading to poor combustion, increased exhaust temperatures, and potential fuel pump damage, often exacerbated by MGO quality or extended service.
  • High-pressure fuel pump element wear (e.g., plungers, delivery valves) due to MGO's lower lubricity compared to HFO, affecting fuel delivery and engine performance.
  • Turbocharger bearing wear (axial/radial play) or compressor/turbine fouling, resulting in reduced boost pressure, increased exhaust temperatures, and potential turbocharger failure.
  • Valve seat recession and valve guide wear, particularly on exhaust valves, due to high thermal loads and operating RPM, leading to loss of compression and increased oil consumption.
  • Piston ring sticking or excessive wear, causing increased blow-by, higher lube oil consumption, and reduced engine efficiency.
  • Lube oil cooler fouling or internal leakage, leading to elevated lube oil temperatures or contamination with cooling water.
  • Vibration damper degradation (e.g., viscous damper fluid leakage or rubber deterioration), critical for a 20-cylinder engine, potentially causing crankshaft damage if unnoticed.
  • Governor malfunction or actuator issues (for mechanical engines), leading to unstable RPM, poor load response, or overspeed conditions.

Inspection checklist

  • Visual inspection for any leaks (fuel, lube oil, cooling water, exhaust gas) around cylinder heads, fuel pumps, turbochargers, and pipe connections.
  • Verification of all critical operating parameters (lube oil pressure/temperature, cooling water pressure/temperature, exhaust gas temperatures per cylinder, turbocharger RPM/boost pressure) against manufacturer's limits and logbook records.
  • Inspection of turbocharger for unusual noise, excessive vibration, and condition of air filters. If accessible, check axial and radial play of the rotor.
  • Examine exhaust gas for abnormal smoke (black, white, blue) at various loads, indicating combustion issues, oil burning, or water ingress.
  • Check condition and tightness of engine mounts and foundation bolts, looking for signs of degradation, corrosion, or movement.
  • Inspect high-pressure fuel injection lines for signs of leakage, chafing, or damage, ensuring all spray shields are correctly fitted and intact.
  • Verify proper operation of local and remote emergency stops, overspeed trip, and other safety shutdown devices.
  • Review engine logbook for recent alarms, maintenance performed, running hours, and lube oil analysis reports.
  • Check crankcase pressure (manometer reading) for signs of excessive blow-by, indicating piston ring or liner wear.
  • Inspect cooling water system for proper level, signs of leaks, and verify records of chemical treatment.

Service intervals

Daily ChecksVisual inspection, log critical parameters (pressures, temperatures, levels).
250-500 Running HoursLube oil and lube oil filter change, fuel filter change (primary and secondary).
1000-2000 Running HoursFuel injector inspection/overhaul (nozzle tips), valve clearance check/adjustment, turbocharger inspection (bearings, cleaning).
4000-6000 Running HoursCylinder head overhaul (valve grinding, seat replacement, spring inspection), fuel pump inspection/calibration, charge air cooler cleaning.
8000-12000 Running HoursPiston and cylinder liner inspection (withdrawal of pistons), connecting rod bearing inspection.
24000-30000 Running HoursMajor overhaul (complete engine strip-down, crankshaft main bearing inspection, crankshaft deflection check, full component renewal/reconditioning).

Typical wear limits

Cylinder Liner Wear (max ovality/taper)0.6 - 0.8 mm
Piston Ring Groove Wear (max clearance increase)0.15 - 0.20 mm
Crankshaft Deflection (max across webs)0.05 - 0.10 mm
Connecting Rod Bearing Clearance (max)0.15 - 0.20 mm
Main Bearing Clearance (max)0.20 - 0.25 mm
Valve Seat Recession (max)0.3 - 0.5 mm
Turbocharger Rotor Axial Play (max)0.10 - 0.15 mm
Turbocharger Rotor Radial Play (max)0.20 - 0.30 mm

Ranges are typical for this design class. Always confirm against the manufacturer documentation for your serial number.

Critical spares

  • Fuel injector assembly (complete unit or nozzle tips for all cylinders)
  • Fuel filters (primary and secondary elements)
  • Lube oil filters (full set)
  • Turbocharger bearing cartridge (or complete service kit)
  • High-pressure fuel pump elements and delivery valves (for at least one cylinder)
  • Cylinder head gasket set (for one cylinder, including valve cover gasket)
  • Starter motor or solenoid
  • Assorted O-rings and gaskets for common access points (e.g., inspection covers, cooling water connections)
  • Temperature and pressure sensors (common types for lube oil, cooling water, exhaust gas)

Safety

  • High-pressure fuel spray from leaks in injection lines or pumps, posing a severe fire hazard. Ensure all spray shields are in place and intact.
  • Hot surfaces (exhaust manifold, turbocharger, charge air cooler) causing burn injuries. Verify insulation is intact and warning signs are present.
  • Rotating machinery (flywheel, drive shafts, cooling fans) presenting entanglement and crushing hazards. Ensure guards are in place and personnel are aware.
  • High noise levels in the engine room, requiring mandatory hearing protection to prevent permanent hearing damage.
  • Potential for crankcase explosion due to accumulation of oil mist and ignition source. Ensure crankcase relief valves are clear, functional, and flame traps are clean.

Class survey

A class surveyor will typically focus on verifying the integrity and operational readiness of the engine and its associated systems. Key checks include: 1. Maintenance Records: Thorough review of Planned Maintenance System (PMS) records, engine logbooks, lube oil analysis reports, and records of critical component replacements/overhauls. 2. Safety Devices: Functional testing of all engine safety devices, including overspeed trip, low lube oil pressure shutdown, high cooling water temperature shutdown, and local/remote emergency stops. 3. Engine Foundation & Mounts: Inspection of engine foundation bolts, chocking, and anti-vibration mounts for tightness, corrosion, and signs of degradation. 4. Fuel Oil System: Verification of fuel oil piping integrity, quick-closing valves, spray shields on high-pressure lines, and fire insulation in way of hot surfaces. 5. Exhaust Gas System: Inspection of exhaust manifold, bellows, insulation, and spark arrestor (if fitted) for leaks or damage. 6. Crankcase Relief Valves: Inspection of crankcase relief valves for freedom of movement and condition of flame traps. 7. General Condition: Overall cleanliness of the engine and engine room, absence of leaks, and proper securing of all components. 8. Operational Test: Witnessing an operational test under load to confirm stable running, adherence to operating parameters, and satisfactory response to load changes. 9. Specific Component Inspections: For Special Surveys, the surveyor may require opening up specific components (e.g., cylinder head lift, bearing inspection) as per the survey cycle or condition monitoring results.

Estimated lifetime: 24,000 - 36,000 hours before major bottom-end overhaul (e.g., crankshaft, main bearings). With diligent maintenance and favorable operating conditions, some units may exceed 40,000 hours.

Need this part?

Request a quote for this model.

Free of charge — send us your request for MTU Onsite Energy equipment. Our team checks it and replies by e-mail.

For marine equipment hardly any maker or authorised dealer will name a price while the vessel is unknown. With the vessel details, availability and price can be settled faster; without them we may have to ask first, which costs a few days. If you are not allowed to name the vessel, a photo of the rating plate is enough — attach it below or send it as a reply to our confirmation e-mail.

Your contact details are not published. No account required.
Related models

Also in Auxiliary Engine (Generator Set).

Other models of the same equipment type, MTU Onsite Energy first.

By manufacturer CaterpillarMAN Energy SolutionsWärtsiläVolvo PentaScaniaMaK (Caterpillar)CumminsDeerePerkinsDaihatsuHanshinMTUYanmarBaudouinDeutzAll manufacturersSpare parts by equipmentNew here? Create a free account Can't read the plate? Try the nameplate scanner All MTU Onsite Energy models More like Series 1163 G-20cyl
More than the data sheet shows

We answer by e-mail, never with an automatic reply.

Tell us what you need for this MTU Onsite Energy Series 1163 G-20cyl — a part, a service call, a second opinion. Are you MTU Onsite Energy? Claim this brand page.

Service engineer? Write the day report for this Series 1163 G-20cyl in OceanSphere Work — photos, hours and parts, as a PDF for the owner. Try it free for 14 days →

Frequently asked

Questions that come up with this equipment.

Is this model's data free?

Yes. Specifications, documents and service notes for this model are readable without an account. An account adds saved searches and requests, nothing is taken away.

Can you find a part for this exact model?

Yes. Tell us the manufacturer, the model and what you need — a person reads every request and replies by e-mail.

The specifications look wrong — what now?

Send us the nameplate or the correct value. We check it against the manufacturer datasheet or class-society record and update the page.