Online Vibration Monitor
An online vibration monitor differs from a portable data collector in one respect that matters more than any spec sheet: it never stops watching, which is the only way to catch a bearing that degrades over hours rather than weeks between rounds.
What to check on an Online Vibration Monitor.
1 models from Endress+Hauser in Online Vibration Monitor. Below: the full model list.
What this type is
An online vibration monitoring system permanently mounts accelerometers or velocity sensors on critical machinery — main engine, propulsion shafting, turbochargers, large pumps and compressors — and feeds their signal continuously to a monitoring unit rather than relying on a technician walking round with a portable collector. The difference from portable monitoring is not accuracy but coverage in time: a permanent system catches a fast-developing fault, such as a turbocharger bearing failing over a few hours, that a monthly or quarterly round would only find after the fact.
Legend
- junction box
- alarm output
- accelerometer
- trend display
- machine
- bearing housing
- monitoring unit
Main components
- Sensors — accelerometers for high-frequency bearing and gear defects, velocity transducers for lower-frequency unbalance and misalignment, sometimes proximity probes for shaft displacement on fluid-film bearings.
- Signal conditioning / data acquisition unit — converts raw sensor signal into usable spectra and trend values, often mounted local to the machine.
- Monitoring processor — runs the alarm logic, stores trend history, and in many installations feeds the vessel's alarm and monitoring system directly.
- Software/HMI — displays spectra, waterfall plots and trend charts, and lets an engineer set alarm thresholds per machine and per measurement point.
Selection and sizing
Sizing is driven by how many measurement points the machinery needs, not by a single monitor size. A main engine may need points on each main bearing and the turbocharger; a shaft line needs axial and radial coverage at the thrust and line bearings. Sensor frequency range must match the fault types expected — gear mesh and bearing defects generate high-frequency content that a low-bandwidth sensor will miss entirely.
| Machine | Typical points | Primary concern |
|---|---|---|
| Main engine bearings | 1 per bearing | Unbalance, misalignment, bearing wear |
| Turbocharger | 1-2 radial | Bearing degradation, blade fouling |
| Shaft line | Thrust + line bearings | Axial movement, alignment drift |
Regulations and class
Class societies offer machinery condition monitoring notations (schemes vary by society) that permit extended survey intervals on machinery covered by an approved online monitoring system, in place of some fixed-interval opening-up inspections. Qualifying for the notation requires the monitoring scope, alarm limits and data retention to meet the society's rules, and the system's calibration record is checked at survey.
Read the full guide
Typical faults
- Sensor cable damaged by heat or chafe near the engine, producing a flat-lined or noisy signal that is mistaken for a healthy machine.
- Alarm thresholds left at factory default rather than set for the specific machine's baseline, causing either nuisance alarms or missed trends.
- Sensor mounting loosened by vibration over time, shifting the measured frequency response and invalidating trend comparisons.
- Software left unmonitored — the system logs data correctly but no one reviews the trend until an alarm finally trips.
What to look for in a supplier
- Sensor frequency range matched to the specific fault types on the machinery in question, not a generic industrial sensor.
- Compatibility with the vessel's existing alarm and monitoring system, or a clear standalone alternative.
- Support for the class society's condition monitoring notation if that is the vessel's goal.
- Local technical support able to help set realistic alarm baselines, not just supply hardware.
A trend line is only as good as its baseline — record a full spectrum on newly installed or overhauled machinery while it is known to be healthy, or every later alarm threshold is a guess.
Models in this type.
The best-documented model of each manufacturer first, then the next — 1 of 1 models in Online Vibration Monitor. Every row links to full specifications, documents and service notes.
Manufacturers.
All 10 manufacturers with models of Online Vibration Monitor. Names with a manufacturer page open it; the others open a search across the full library.
All manufacturers in the libraryAlso in Vibration Monitoring.
The other equipment types in this category.
Write to us about your machine — the answer comes by e-mail.
Name the make and the model and what the job is: a spare, a service call, a second opinion on a data sheet. We answer by e-mail.
No details at hand? A photo of the rating plate or the part is enough — simply attach it to the request.
Questions that come up with this equipment.
Is Online Vibration Monitor data free?
Yes. Every model page, every guide and every datasheet for this type is readable without an account. An account adds saved searches and requests, nothing is taken away.
My model is missing — what now?
Send us the nameplate. We identify it by hand, add it to the library, and if you need a part or a service, the request is already on our desk.
Can you source a Online Vibration Monitor part?
Yes. Tell us the manufacturer, the model and what you need — a person reads every request and replies by e-mail.