Bearing Temperature Monitor
A bearing temperature monitor tracks main bearing and crankpin temperatures directly with embedded sensors, catching a developing bearing failure earlier than an oil mist detector, which only responds once oil is already vaporising.
What to check on a Bearing Temperature Monitor.
1 models from Danfoss in Bearing Temperature Monitor. Below: the full model list.
What defines a bearing temperature monitor
A bearing temperature monitoring system measures the temperature of main bearings and, on larger engines, crankpin (big end) bearings directly, using sensors embedded in or near the bearing shell. It complements rather than replaces an oil mist detector: oil mist detection senses the consequence of overheating, an oil mist cloud in the crankcase, while direct temperature monitoring catches the rise in bearing metal temperature at an earlier stage, often before any mist is generated at all. On engines with crankpin monitoring, the signal has to cross a rotating-to-stationary interface, which is the main engineering challenge in this equipment.
Legend
- bearing housing
- bearing temperature monitor
- per-bearing display, each channel alarm relay output
- journal (crankshaft)
- shell (bearing metal)
- alarm
- temperature sensor (RTD)
- cable to monitor
Main components
Temperature sensors
Resistance temperature detectors or thermocouples are fitted into the bearing shell or housing, positioned close to the loaded zone where heat generation is highest.
Signal transmission for rotating bearings
For crankpin bearings, the signal must pass from the rotating crankshaft to the stationary monitoring unit, done either through slip rings or, on modern systems, through inductive or telemetry-based wireless transmission that avoids the wear associated with slip rings.
Read the full guide
Monitoring and alarm unit
Collects readings from all monitored bearings, compares each against individually configured alarm and slow-down thresholds, and displays trends so the crew can see a bearing heating up gradually rather than only reacting to a sudden alarm.
Interface to the engine safety system
High-temperature alarms and, on many installations, automatic slow-down or shutdown signals are wired into the main engine's safety and control system, so a confirmed overheat trips a protective action without waiting for crew intervention.
Selection and sizing
The number of monitored points is the key sizing decision: monitoring every main bearing and every crankpin bearing gives full coverage but costs more in sensors and, for crankpin points, in the rotating signal transmission hardware. Some owners monitor main bearings on all cylinders but only a sample of crankpin bearings, accepting reduced coverage to control cost. Alarm and slow-down set points must be matched to the bearing material and the engine maker's guidance rather than a generic default, since white metal and other bearing materials have different safe operating temperature margins.
Regulations and class
Class societies increasingly require, or grant notations for, continuous bearing condition monitoring on larger engines, particularly where it forms part of an extended survey or condition-based maintenance scheme that replaces a fixed overhaul interval. Where fitted as part of such a scheme, class specifies minimum sensor coverage, alarm response and record-keeping requirements before accepting extended intervals between crankcase inspections.
Typical faults
- Sensor drift over time, giving a falsely low reading and masking a genuine temperature rise until damage has already occurred
- Slip ring wear on crankpin monitoring, causing intermittent signal loss that crews learn to ignore as a nuisance alarm
- Wiring damage from the harsh crankcase environment, oil, vibration and heat, breaking continuity to one or more sensors
- Alarm thresholds left at factory default rather than tuned to the specific bearing material and load, causing either false alarms or a dangerously late warning
What to look for in a supplier
- Sensor and transmission technology proven on the specific engine make and cylinder configuration
- Integration confirmed with the engine's existing safety and alarm system rather than a standalone display nobody watches
- Access to historical trend data, not just an instantaneous reading, to catch a slow drift before it becomes an alarm
- Spare sensor availability and a realistic replacement procedure that does not require opening the crankcase for a routine sensor swap
Treat a slowly rising bearing temperature trend as more urgent than an oil mist alarm; by the time mist forms, the bearing is already well past where direct monitoring would have caught it.
Models in this type.
The best-documented model of each manufacturer first, then the next — 1 of 1 models in Bearing Temperature Monitor. Every row links to full specifications, documents and service notes.
Manufacturers.
All 7 manufacturers with models of Bearing Temperature Monitor. Names with a manufacturer page open it; the others open a search across the full library.
All manufacturers in the libraryAlso in Oil Mist Detection.
The other equipment types in this category.
Write to us about this model — the answer comes by e-mail.
Name the make and the model and what the job is: a spare, a service call, a second opinion on a data sheet. We answer by e-mail.
No details at hand? A photo of the rating plate or the part is enough — simply attach it to the request.
Questions that come up with this equipment.
Is Bearing Temperature Monitor data free?
Yes. Every model page, every guide and every datasheet for this type is readable without an account. An account adds saved searches and requests, nothing is taken away.
My model is missing — what now?
Send us the nameplate. We identify it by hand, add it to the library, and if you need a part or a service, the request is already on our desk.
Can you source a Bearing Temperature Monitor part?
Yes. Tell us the manufacturer, the model and what you need — a person reads every request and replies by e-mail.