Tumble Dryer (Marine)
medium
57 models total
A marine tumble dryer moves several hundred kilograms of wet linen a day through a steam- or electrically heated drum, and its main engineering risk is not water but the lint it sheds into a duct that runs straight to open deck.
Read more — Tumble Dryer (Marine) explained ▾
What sets a marine tumble dryer apart from the shore version
A domestic dryer vents warm moist air a few metres to an outside wall. A marine dryer usually sits several decks below the weather deck, so the exhaust has to travel through a long, rising duct against the ship's roll and pitch, past fire zone boundaries, and out through a weathertight cowl. That duct run, not the drum itself, is where most marine-specific engineering goes. The heat source is the second difference: many vessels run the dryer off the same steam range used for the calender and the galley, because steam is already available at low pressure and does not add electrical load to a generator that is already carrying hotel and machinery services.
Main components
Drum and drive
The perforated stainless steel drum is belt- or direct-driven and reverses direction on a timed cycle to stop laundry balling up in a single mass, which would otherwise dry unevenly and place an eccentric load on the bearings while the ship is rolling.
Heat source
Steam-heated units draw off the ship's low-pressure range through a finned heating coil and a steam trap; electrically heated units use resistance elements staged in banks so the control system can step heat output up or down without cycling the whole load on and off.
Lint filtration
A primary lint screen sits directly in the airstream at the drum outlet and needs clearing after every load; a secondary screen or lint trap downstream catches what the first one misses before air reaches the fan and duct.
Exhaust ducting and fan
An extraction fan pulls moist air through the duct run to a weather deck outlet fitted with a non-return damper so following seas or wind gusts cannot force water back down the duct into the laundry.
Sizing and heat source selection
Dryer capacity is quoted in kilograms of dry laundry per batch and should be matched to the washing machine capacity feeding it, typically at a similar or slightly larger kilogram rating so the dryer is not run as the bottleneck of the laundry cycle. The choice between steam and electric heat usually comes down to what is already installed: a vessel with a steam range for the galley and calender gains little by adding an electric dryer, while a vessel with no low-pressure steam distribution avoids running a dedicated steam line for one machine.
| Factor | Steam heat | Electric heat |
|---|---|---|
| Installation | Needs steam and condensate return piping | Needs a dedicated feeder from the switchboard |
| Heat-up time | Fast once steam is available | Slower, staged by element banks |
| Running cost | Uses waste or boiler steam | Draws directly on generator capacity |
Regulations and class
Class and SOLAS Chapter II-2 requirements for laundry spaces centre on fire safety rather than on the dryer as a machine: the exhaust duct routing through fire zones needs fire dampers or equivalent protection where it penetrates a boundary, and lint accumulation inside the duct is treated as a recognised fire source during surveys. Electrically heated units fall under the same periodic insulation resistance and earth continuity checks as other fixed electrical machinery.
Typical faults
- Lint-blocked duct — restricts airflow, extends drying time, and raises the surface temperature of the heating coil until it becomes a fire source.
- Failed steam trap — lets condensate collect in the heating coil, causing water hammer and uneven heat output.
- Worn drum bearings — from years of eccentric loading, producing vibration that eventually damages the drive belt or motor mounts.
- Damaged door seal — lets moist air escape into the laundry space, raising ambient humidity and corrosion risk on nearby steelwork.
What to look for in a supplier
- Marine type approval for the specific heat source, not a rebadged commercial-laundry unit.
- Drum and cabinet material rated for the humid, salt-laden atmosphere of a ship's laundry.
- Duct and fan sized against the actual vertical and horizontal run on the vessel, not a generic shore installation figure.
- Availability of the specific heating coil or element bank as a spare part, since these are the components that fail first.
Clear the lint screen after every single load, not once a shift — it takes thirty seconds and is the cheapest fire prevention measure in the laundry.
5 manufacturers · 57 models
IPSO Marine
15
IY65 230V Marine
unverified
· 13.0 kW
Capacity (kg)
65
Drum volume (l)
780
Power (kW)
13.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Restricted airflow caused by lint buildup, blocked filters or ducting, resulting in long drying cycles, overheating or protective trips
- Heater or temperature-control failure caused by element, sensor or control faults, resulting in no heat, overheating or aborted cycles
- Drive-belt, motor or bearing deterioration caused by wear, overloading or misalignment, resulting in noise, poor drum rotation or stoppage
- Electrical-control faults caused by moisture, loose connections or component failure, resulting in intermittent operation, alarms or breaker trips
- Door seal, hose or connection leakage caused by wear or loosening, resulting in water, condensate or air leakage around the machine
Service: Clean lint filters and inspect exhaust or condenser airflow paths frequently. Inspect drum supports, bearings, drive components, door seals and electrical connections for wear or overheating. Verify safety interlocks and emergency stop functions where fitted. Keep the machine securely fastened to its marine foundation and inspect anti-vibration mounts. Investigate repeated trips rather than resetting the machine without identifying the cause. Refer to the manufacturer documentation for exact servicing intervals and electrical checks.
Spare Parts: Keep door seals, drive belts where fitted, filters, selected valves or pumps, fuses and manufacturer-recommended control or sensor components. For passenger or hotel-service vessels, additional wear items may be justified because of high utilization. Confirm exact spares from the model and serial number.
Use Cases: Crew, passenger and hotel-service laundry on merchant ships, ferries, cruise vessels and offshore accommodation units.
IY65 400V Marine
unverified
· 13.0 kW
Capacity (kg)
65
Drum volume (l)
780
Power (kW)
13.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Restricted airflow caused by lint buildup, blocked filters or ducting, resulting in long drying cycles, overheating or protective trips
- Heater or temperature-control failure caused by element, sensor or control faults, resulting in no heat, overheating or aborted cycles
- Drive-belt, motor or bearing deterioration caused by wear, overloading or misalignment, resulting in noise, poor drum rotation or stoppage
- Electrical-control faults caused by moisture, loose connections or component failure, resulting in intermittent operation, alarms or breaker trips
- Door seal, hose or connection leakage caused by wear or loosening, resulting in water, condensate or air leakage around the machine
Service: Clean lint filters and inspect exhaust or condenser airflow paths frequently. Inspect drum supports, bearings, drive components, door seals and electrical connections for wear or overheating. Verify safety interlocks and emergency stop functions where fitted. Keep the machine securely fastened to its marine foundation and inspect anti-vibration mounts. Investigate repeated trips rather than resetting the machine without identifying the cause. Refer to the manufacturer documentation for exact servicing intervals and electrical checks.
Spare Parts: Keep door seals, drive belts where fitted, filters, selected valves or pumps, fuses and manufacturer-recommended control or sensor components. For passenger or hotel-service vessels, additional wear items may be justified because of high utilization. Confirm exact spares from the model and serial number.
Use Cases: Crew, passenger and hotel-service laundry on merchant ships, ferries, cruise vessels and offshore accommodation units.
IY65 440V Marine
unverified
· 13.0 kW
Capacity (kg)
65
Drum volume (l)
780
Power (kW)
13.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Restricted airflow caused by lint buildup, blocked filters or ducting, resulting in long drying cycles, overheating or protective trips
- Heater or temperature-control failure caused by element, sensor or control faults, resulting in no heat, overheating or aborted cycles
- Drive-belt, motor or bearing deterioration caused by wear, overloading or misalignment, resulting in noise, poor drum rotation or stoppage
- Electrical-control faults caused by moisture, loose connections or component failure, resulting in intermittent operation, alarms or breaker trips
- Door seal, hose or connection leakage caused by wear or loosening, resulting in water, condensate or air leakage around the machine
Service: Clean lint filters and inspect exhaust or condenser airflow paths frequently. Inspect drum supports, bearings, drive components, door seals and electrical connections for wear or overheating. Verify safety interlocks and emergency stop functions where fitted. Keep the machine securely fastened to its marine foundation and inspect anti-vibration mounts. Investigate repeated trips rather than resetting the machine without identifying the cause. Refer to the manufacturer documentation for exact servicing intervals and electrical checks.
Spare Parts: Keep door seals, drive belts where fitted, filters, selected valves or pumps, fuses and manufacturer-recommended control or sensor components. For passenger or hotel-service vessels, additional wear items may be justified because of high utilization. Confirm exact spares from the model and serial number.
Use Cases: Crew, passenger and hotel-service laundry on merchant ships, ferries, cruise vessels and offshore accommodation units.
IY105 230V Marine
unverified
· 20.0 kW
Capacity (kg)
100
Drum volume (l)
1200
Power (kW)
20.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Restricted airflow caused by lint buildup, blocked filters or ducting, resulting in long drying cycles, overheating or protective trips
- Heater or temperature-control failure caused by element, sensor or control faults, resulting in no heat, overheating or aborted cycles
- Drive-belt, motor or bearing deterioration caused by wear, overloading or misalignment, resulting in noise, poor drum rotation or stoppage
- Electrical-control faults caused by moisture, loose connections or component failure, resulting in intermittent operation, alarms or breaker trips
- Door seal, hose or connection leakage caused by wear or loosening, resulting in water, condensate or air leakage around the machine
Service: Clean lint filters and inspect exhaust or condenser airflow paths frequently. Inspect drum supports, bearings, drive components, door seals and electrical connections for wear or overheating. Verify safety interlocks and emergency stop functions where fitted. Keep the machine securely fastened to its marine foundation and inspect anti-vibration mounts. Investigate repeated trips rather than resetting the machine without identifying the cause. Refer to the manufacturer documentation for exact servicing intervals and electrical checks.
Spare Parts: Keep door seals, drive belts where fitted, filters, selected valves or pumps, fuses and manufacturer-recommended control or sensor components. For passenger or hotel-service vessels, additional wear items may be justified because of high utilization. Confirm exact spares from the model and serial number.
Use Cases: Crew, passenger and hotel-service laundry on merchant ships, ferries, cruise vessels and offshore accommodation units.
IY105 400V Marine
unverified
· 20.0 kW
Capacity (kg)
100
Drum volume (l)
1200
Power (kW)
20.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Restricted airflow caused by lint buildup, blocked filters or ducting, resulting in long drying cycles, overheating or protective trips
- Heater or temperature-control failure caused by element, sensor or control faults, resulting in no heat, overheating or aborted cycles
- Drive-belt, motor or bearing deterioration caused by wear, overloading or misalignment, resulting in noise, poor drum rotation or stoppage
- Electrical-control faults caused by moisture, loose connections or component failure, resulting in intermittent operation, alarms or breaker trips
- Door seal, hose or connection leakage caused by wear or loosening, resulting in water, condensate or air leakage around the machine
Service: Clean lint filters and inspect exhaust or condenser airflow paths frequently. Inspect drum supports, bearings, drive components, door seals and electrical connections for wear or overheating. Verify safety interlocks and emergency stop functions where fitted. Keep the machine securely fastened to its marine foundation and inspect anti-vibration mounts. Investigate repeated trips rather than resetting the machine without identifying the cause. Refer to the manufacturer documentation for exact servicing intervals and electrical checks.
Spare Parts: Keep door seals, drive belts where fitted, filters, selected valves or pumps, fuses and manufacturer-recommended control or sensor components. For passenger or hotel-service vessels, additional wear items may be justified because of high utilization. Confirm exact spares from the model and serial number.
Use Cases: Crew, passenger and hotel-service laundry on merchant ships, ferries, cruise vessels and offshore accommodation units.
IY105 440V Marine
unverified
· 20.0 kW
Capacity (kg)
100
Drum volume (l)
1200
Power (kW)
20.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Restricted airflow caused by lint buildup, blocked filters or ducting, resulting in long drying cycles, overheating or protective trips
- Heater or temperature-control failure caused by element, sensor or control faults, resulting in no heat, overheating or aborted cycles
- Drive-belt, motor or bearing deterioration caused by wear, overloading or misalignment, resulting in noise, poor drum rotation or stoppage
- Electrical-control faults caused by moisture, loose connections or component failure, resulting in intermittent operation, alarms or breaker trips
- Door seal, hose or connection leakage caused by wear or loosening, resulting in water, condensate or air leakage around the machine
Service: Clean lint filters and inspect exhaust or condenser airflow paths frequently. Inspect drum supports, bearings, drive components, door seals and electrical connections for wear or overheating. Verify safety interlocks and emergency stop functions where fitted. Keep the machine securely fastened to its marine foundation and inspect anti-vibration mounts. Investigate repeated trips rather than resetting the machine without identifying the cause. Refer to the manufacturer documentation for exact servicing intervals and electrical checks.
Spare Parts: Keep door seals, drive belts where fitted, filters, selected valves or pumps, fuses and manufacturer-recommended control or sensor components. For passenger or hotel-service vessels, additional wear items may be justified because of high utilization. Confirm exact spares from the model and serial number.
Use Cases: Crew, passenger and hotel-service laundry on merchant ships, ferries, cruise vessels and offshore accommodation units.
IY135 230V Marine
unverified
· 20.0 kW
Capacity (kg)
100
Drum volume (l)
1200
Power (kW)
20.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Restricted airflow caused by lint buildup, blocked filters or ducting, resulting in long drying cycles, overheating or protective trips
- Heater or temperature-control failure caused by element, sensor or control faults, resulting in no heat, overheating or aborted cycles
- Drive-belt, motor or bearing deterioration caused by wear, overloading or misalignment, resulting in noise, poor drum rotation or stoppage
- Electrical-control faults caused by moisture, loose connections or component failure, resulting in intermittent operation, alarms or breaker trips
- Door seal, hose or connection leakage caused by wear or loosening, resulting in water, condensate or air leakage around the machine
Service: Clean lint filters and inspect exhaust or condenser airflow paths frequently. Inspect drum supports, bearings, drive components, door seals and electrical connections for wear or overheating. Verify safety interlocks and emergency stop functions where fitted. Keep the machine securely fastened to its marine foundation and inspect anti-vibration mounts. Investigate repeated trips rather than resetting the machine without identifying the cause. Refer to the manufacturer documentation for exact servicing intervals and electrical checks.
Spare Parts: Keep door seals, drive belts where fitted, filters, selected valves or pumps, fuses and manufacturer-recommended control or sensor components. For passenger or hotel-service vessels, additional wear items may be justified because of high utilization. Confirm exact spares from the model and serial number.
Use Cases: Crew, passenger and hotel-service laundry on merchant ships, ferries, cruise vessels and offshore accommodation units.
IY135 400V Marine
unverified
· 20.0 kW
Capacity (kg)
100
Drum volume (l)
1200
Power (kW)
20.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Restricted airflow caused by lint buildup, blocked filters or ducting, resulting in long drying cycles, overheating or protective trips
- Heater or temperature-control failure caused by element, sensor or control faults, resulting in no heat, overheating or aborted cycles
- Drive-belt, motor or bearing deterioration caused by wear, overloading or misalignment, resulting in noise, poor drum rotation or stoppage
- Electrical-control faults caused by moisture, loose connections or component failure, resulting in intermittent operation, alarms or breaker trips
- Door seal, hose or connection leakage caused by wear or loosening, resulting in water, condensate or air leakage around the machine
Service: Clean lint filters and inspect exhaust or condenser airflow paths frequently. Inspect drum supports, bearings, drive components, door seals and electrical connections for wear or overheating. Verify safety interlocks and emergency stop functions where fitted. Keep the machine securely fastened to its marine foundation and inspect anti-vibration mounts. Investigate repeated trips rather than resetting the machine without identifying the cause. Refer to the manufacturer documentation for exact servicing intervals and electrical checks.
Spare Parts: Keep door seals, drive belts where fitted, filters, selected valves or pumps, fuses and manufacturer-recommended control or sensor components. For passenger or hotel-service vessels, additional wear items may be justified because of high utilization. Confirm exact spares from the model and serial number.
Use Cases: Crew, passenger and hotel-service laundry on merchant ships, ferries, cruise vessels and offshore accommodation units.
IY135 440V Marine
unverified
· 20.0 kW
Capacity (kg)
100
Drum volume (l)
1200
Power (kW)
20.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Restricted airflow caused by lint buildup, blocked filters or ducting, resulting in long drying cycles, overheating or protective trips
- Heater or temperature-control failure caused by element, sensor or control faults, resulting in no heat, overheating or aborted cycles
- Drive-belt, motor or bearing deterioration caused by wear, overloading or misalignment, resulting in noise, poor drum rotation or stoppage
- Electrical-control faults caused by moisture, loose connections or component failure, resulting in intermittent operation, alarms or breaker trips
- Door seal, hose or connection leakage caused by wear or loosening, resulting in water, condensate or air leakage around the machine
Service: Clean lint filters and inspect exhaust or condenser airflow paths frequently. Inspect drum supports, bearings, drive components, door seals and electrical connections for wear or overheating. Verify safety interlocks and emergency stop functions where fitted. Keep the machine securely fastened to its marine foundation and inspect anti-vibration mounts. Investigate repeated trips rather than resetting the machine without identifying the cause. Refer to the manufacturer documentation for exact servicing intervals and electrical checks.
Spare Parts: Keep door seals, drive belts where fitted, filters, selected valves or pumps, fuses and manufacturer-recommended control or sensor components. For passenger or hotel-service vessels, additional wear items may be justified because of high utilization. Confirm exact spares from the model and serial number.
Use Cases: Crew, passenger and hotel-service laundry on merchant ships, ferries, cruise vessels and offshore accommodation units.
IY180 230V Marine
unverified
· 20.0 kW
Capacity (kg)
100
Drum volume (l)
1200
Power (kW)
20.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Restricted airflow caused by lint buildup, blocked filters or ducting, resulting in long drying cycles, overheating or protective trips
- Heater or temperature-control failure caused by element, sensor or control faults, resulting in no heat, overheating or aborted cycles
- Drive-belt, motor or bearing deterioration caused by wear, overloading or misalignment, resulting in noise, poor drum rotation or stoppage
- Electrical-control faults caused by moisture, loose connections or component failure, resulting in intermittent operation, alarms or breaker trips
- Door seal, hose or connection leakage caused by wear or loosening, resulting in water, condensate or air leakage around the machine
Service: Clean lint filters and inspect exhaust or condenser airflow paths frequently. Inspect drum supports, bearings, drive components, door seals and electrical connections for wear or overheating. Verify safety interlocks and emergency stop functions where fitted. Keep the machine securely fastened to its marine foundation and inspect anti-vibration mounts. Investigate repeated trips rather than resetting the machine without identifying the cause. Refer to the manufacturer documentation for exact servicing intervals and electrical checks.
Spare Parts: Keep door seals, drive belts where fitted, filters, selected valves or pumps, fuses and manufacturer-recommended control or sensor components. For passenger or hotel-service vessels, additional wear items may be justified because of high utilization. Confirm exact spares from the model and serial number.
Use Cases: Crew, passenger and hotel-service laundry on merchant ships, ferries, cruise vessels and offshore accommodation units.
IY180 400V Marine
unverified
· 20.0 kW
Capacity (kg)
100
Drum volume (l)
1200
Power (kW)
20.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Restricted airflow caused by lint buildup, blocked filters or ducting, resulting in long drying cycles, overheating or protective trips
- Heater or temperature-control failure caused by element, sensor or control faults, resulting in no heat, overheating or aborted cycles
- Drive-belt, motor or bearing deterioration caused by wear, overloading or misalignment, resulting in noise, poor drum rotation or stoppage
- Electrical-control faults caused by moisture, loose connections or component failure, resulting in intermittent operation, alarms or breaker trips
- Door seal, hose or connection leakage caused by wear or loosening, resulting in water, condensate or air leakage around the machine
Service: Clean lint filters and inspect exhaust or condenser airflow paths frequently. Inspect drum supports, bearings, drive components, door seals and electrical connections for wear or overheating. Verify safety interlocks and emergency stop functions where fitted. Keep the machine securely fastened to its marine foundation and inspect anti-vibration mounts. Investigate repeated trips rather than resetting the machine without identifying the cause. Refer to the manufacturer documentation for exact servicing intervals and electrical checks.
Spare Parts: Keep door seals, drive belts where fitted, filters, selected valves or pumps, fuses and manufacturer-recommended control or sensor components. For passenger or hotel-service vessels, additional wear items may be justified because of high utilization. Confirm exact spares from the model and serial number.
Use Cases: Crew, passenger and hotel-service laundry on merchant ships, ferries, cruise vessels and offshore accommodation units.
IY180 440V Marine
unverified
· 20.0 kW
Capacity (kg)
100
Drum volume (l)
1200
Power (kW)
20.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Restricted airflow caused by lint buildup, blocked filters or ducting, resulting in long drying cycles, overheating or protective trips
- Heater or temperature-control failure caused by element, sensor or control faults, resulting in no heat, overheating or aborted cycles
- Drive-belt, motor or bearing deterioration caused by wear, overloading or misalignment, resulting in noise, poor drum rotation or stoppage
- Electrical-control faults caused by moisture, loose connections or component failure, resulting in intermittent operation, alarms or breaker trips
- Door seal, hose or connection leakage caused by wear or loosening, resulting in water, condensate or air leakage around the machine
Service: Clean lint filters and inspect exhaust or condenser airflow paths frequently. Inspect drum supports, bearings, drive components, door seals and electrical connections for wear or overheating. Verify safety interlocks and emergency stop functions where fitted. Keep the machine securely fastened to its marine foundation and inspect anti-vibration mounts. Investigate repeated trips rather than resetting the machine without identifying the cause. Refer to the manufacturer documentation for exact servicing intervals and electrical checks.
Spare Parts: Keep door seals, drive belts where fitted, filters, selected valves or pumps, fuses and manufacturer-recommended control or sensor components. For passenger or hotel-service vessels, additional wear items may be justified because of high utilization. Confirm exact spares from the model and serial number.
Use Cases: Crew, passenger and hotel-service laundry on merchant ships, ferries, cruise vessels and offshore accommodation units.
IY235 230V Marine
unverified
· 20.0 kW
Capacity (kg)
100
Drum volume (l)
1200
Power (kW)
20.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Restricted airflow caused by lint buildup, blocked filters or ducting, resulting in long drying cycles, overheating or protective trips
- Heater or temperature-control failure caused by element, sensor or control faults, resulting in no heat, overheating or aborted cycles
- Drive-belt, motor or bearing deterioration caused by wear, overloading or misalignment, resulting in noise, poor drum rotation or stoppage
- Electrical-control faults caused by moisture, loose connections or component failure, resulting in intermittent operation, alarms or breaker trips
- Door seal, hose or connection leakage caused by wear or loosening, resulting in water, condensate or air leakage around the machine
Service: Clean lint filters and inspect exhaust or condenser airflow paths frequently. Inspect drum supports, bearings, drive components, door seals and electrical connections for wear or overheating. Verify safety interlocks and emergency stop functions where fitted. Keep the machine securely fastened to its marine foundation and inspect anti-vibration mounts. Investigate repeated trips rather than resetting the machine without identifying the cause. Refer to the manufacturer documentation for exact servicing intervals and electrical checks.
Spare Parts: Keep door seals, drive belts where fitted, filters, selected valves or pumps, fuses and manufacturer-recommended control or sensor components. For passenger or hotel-service vessels, additional wear items may be justified because of high utilization. Confirm exact spares from the model and serial number.
Use Cases: Crew, passenger and hotel-service laundry on merchant ships, ferries, cruise vessels and offshore accommodation units.
IY235 400V Marine
unverified
· 20.0 kW
Capacity (kg)
100
Drum volume (l)
1200
Power (kW)
20.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Restricted airflow caused by lint buildup, blocked filters or ducting, resulting in long drying cycles, overheating or protective trips
- Heater or temperature-control failure caused by element, sensor or control faults, resulting in no heat, overheating or aborted cycles
- Drive-belt, motor or bearing deterioration caused by wear, overloading or misalignment, resulting in noise, poor drum rotation or stoppage
- Electrical-control faults caused by moisture, loose connections or component failure, resulting in intermittent operation, alarms or breaker trips
- Door seal, hose or connection leakage caused by wear or loosening, resulting in water, condensate or air leakage around the machine
Service: Clean lint filters and inspect exhaust or condenser airflow paths frequently. Inspect drum supports, bearings, drive components, door seals and electrical connections for wear or overheating. Verify safety interlocks and emergency stop functions where fitted. Keep the machine securely fastened to its marine foundation and inspect anti-vibration mounts. Investigate repeated trips rather than resetting the machine without identifying the cause. Refer to the manufacturer documentation for exact servicing intervals and electrical checks.
Spare Parts: Keep door seals, drive belts where fitted, filters, selected valves or pumps, fuses and manufacturer-recommended control or sensor components. For passenger or hotel-service vessels, additional wear items may be justified because of high utilization. Confirm exact spares from the model and serial number.
Use Cases: Crew, passenger and hotel-service laundry on merchant ships, ferries, cruise vessels and offshore accommodation units.
IY235 440V Marine
unverified
· 20.0 kW
Capacity (kg)
100
Drum volume (l)
1200
Power (kW)
20.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Restricted airflow caused by lint buildup, blocked filters or ducting, resulting in long drying cycles, overheating or protective trips
- Heater or temperature-control failure caused by element, sensor or control faults, resulting in no heat, overheating or aborted cycles
- Drive-belt, motor or bearing deterioration caused by wear, overloading or misalignment, resulting in noise, poor drum rotation or stoppage
- Electrical-control faults caused by moisture, loose connections or component failure, resulting in intermittent operation, alarms or breaker trips
- Door seal, hose or connection leakage caused by wear or loosening, resulting in water, condensate or air leakage around the machine
Service: Clean lint filters and inspect exhaust or condenser airflow paths frequently. Inspect drum supports, bearings, drive components, door seals and electrical connections for wear or overheating. Verify safety interlocks and emergency stop functions where fitted. Keep the machine securely fastened to its marine foundation and inspect anti-vibration mounts. Investigate repeated trips rather than resetting the machine without identifying the cause. Refer to the manufacturer documentation for exact servicing intervals and electrical checks.
Spare Parts: Keep door seals, drive belts where fitted, filters, selected valves or pumps, fuses and manufacturer-recommended control or sensor components. For passenger or hotel-service vessels, additional wear items may be justified because of high utilization. Confirm exact spares from the model and serial number.
Use Cases: Crew, passenger and hotel-service laundry on merchant ships, ferries, cruise vessels and offshore accommodation units.
Electrolux Professional Marine
12
T5190 230V Marine
unverified
· 20.0 kW
Capacity (kg)
100
Drum volume (l)
1200
Power (kW)
20.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Door seal or latch wear, typically indicated by water leakage or inability to start
- Drain pump/filter blockage, typically indicated by standing water, slow drain or alarm
- Heating element or thermostat failure, typically indicated by poor washing/drying performance or trip
- Motor, belt or bearing wear, typically indicated by noise, drum not turning or vibration
- Lint/airflow blockage in dryers, typically indicated by long drying times or overheating
Service: Inspect door seals, filters, drains, heating controls, motors, bearings, belts and dryer lint/exhaust paths; verify electrical safety and secure marine mounting.
Spare Parts: Keep door seals, drain pumps, belts, heating elements/thermostats, filters and common control relays appropriate to the installed machines.
Use Cases: Used in crew and passenger laundries on merchant, passenger, offshore and naval vessels. This entry applies specifically to the Tumble Dryer (Marine) variant identified as Electrolux Professional Marine T5190 230V Marine.
T5190 400V Marine
unverified
· 20.0 kW
Capacity (kg)
100
Drum volume (l)
1200
Power (kW)
20.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Door seal or latch wear, typically indicated by water leakage or inability to start
- Drain pump/filter blockage, typically indicated by standing water, slow drain or alarm
- Heating element or thermostat failure, typically indicated by poor washing/drying performance or trip
- Motor, belt or bearing wear, typically indicated by noise, drum not turning or vibration
- Lint/airflow blockage in dryers, typically indicated by long drying times or overheating
Service: Inspect door seals, filters, drains, heating controls, motors, bearings, belts and dryer lint/exhaust paths; verify electrical safety and secure marine mounting.
Spare Parts: Keep door seals, drain pumps, belts, heating elements/thermostats, filters and common control relays appropriate to the installed machines.
Use Cases: Used in crew and passenger laundries on merchant, passenger, offshore and naval vessels. This entry applies specifically to the Tumble Dryer (Marine) variant identified as Electrolux Professional Marine T5190 400V Marine.
T5190 440V Marine
unverified
· 20.0 kW
Capacity (kg)
100
Drum volume (l)
1200
Power (kW)
20.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Door seal or latch wear, typically indicated by water leakage or inability to start
- Drain pump/filter blockage, typically indicated by standing water, slow drain or alarm
- Heating element or thermostat failure, typically indicated by poor washing/drying performance or trip
- Motor, belt or bearing wear, typically indicated by noise, drum not turning or vibration
- Lint/airflow blockage in dryers, typically indicated by long drying times or overheating
Service: Inspect door seals, filters, drains, heating controls, motors, bearings, belts and dryer lint/exhaust paths; verify electrical safety and secure marine mounting.
Spare Parts: Keep door seals, drain pumps, belts, heating elements/thermostats, filters and common control relays appropriate to the installed machines.
Use Cases: Used in crew and passenger laundries on merchant, passenger, offshore and naval vessels. This entry applies specifically to the Tumble Dryer (Marine) variant identified as Electrolux Professional Marine T5190 440V Marine.
T5290 230V Marine
unverified
· 20.0 kW
Capacity (kg)
100
Drum volume (l)
1200
Power (kW)
20.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Door seal or latch wear, typically indicated by water leakage or inability to start
- Drain pump/filter blockage, typically indicated by standing water, slow drain or alarm
- Heating element or thermostat failure, typically indicated by poor washing/drying performance or trip
- Motor, belt or bearing wear, typically indicated by noise, drum not turning or vibration
- Lint/airflow blockage in dryers, typically indicated by long drying times or overheating
Service: Inspect door seals, filters, drains, heating controls, motors, bearings, belts and dryer lint/exhaust paths; verify electrical safety and secure marine mounting.
Spare Parts: Keep door seals, drain pumps, belts, heating elements/thermostats, filters and common control relays appropriate to the installed machines.
Use Cases: Used in crew and passenger laundries on merchant, passenger, offshore and naval vessels. This entry applies specifically to the Tumble Dryer (Marine) variant identified as Electrolux Professional Marine T5290 230V Marine.
T5290 400V Marine
unverified
· 20.0 kW
Capacity (kg)
100
Drum volume (l)
1200
Power (kW)
20.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Door seal or latch wear, typically indicated by water leakage or inability to start
- Drain pump/filter blockage, typically indicated by standing water, slow drain or alarm
- Heating element or thermostat failure, typically indicated by poor washing/drying performance or trip
- Motor, belt or bearing wear, typically indicated by noise, drum not turning or vibration
- Lint/airflow blockage in dryers, typically indicated by long drying times or overheating
Service: Inspect door seals, filters, drains, heating controls, motors, bearings, belts and dryer lint/exhaust paths; verify electrical safety and secure marine mounting.
Spare Parts: Keep door seals, drain pumps, belts, heating elements/thermostats, filters and common control relays appropriate to the installed machines.
Use Cases: Used in crew and passenger laundries on merchant, passenger, offshore and naval vessels. This entry applies specifically to the Tumble Dryer (Marine) variant identified as Electrolux Professional Marine T5290 400V Marine.
T5290 440V Marine
unverified
· 20.0 kW
Capacity (kg)
100
Drum volume (l)
1200
Power (kW)
20.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Door seal or latch wear, typically indicated by water leakage or inability to start
- Drain pump/filter blockage, typically indicated by standing water, slow drain or alarm
- Heating element or thermostat failure, typically indicated by poor washing/drying performance or trip
- Motor, belt or bearing wear, typically indicated by noise, drum not turning or vibration
- Lint/airflow blockage in dryers, typically indicated by long drying times or overheating
Service: Inspect door seals, filters, drains, heating controls, motors, bearings, belts and dryer lint/exhaust paths; verify electrical safety and secure marine mounting.
Spare Parts: Keep door seals, drain pumps, belts, heating elements/thermostats, filters and common control relays appropriate to the installed machines.
Use Cases: Used in crew and passenger laundries on merchant, passenger, offshore and naval vessels. This entry applies specifically to the Tumble Dryer (Marine) variant identified as Electrolux Professional Marine T5290 440V Marine.
T5350 230V Marine
unverified
· 20.0 kW
Capacity (kg)
100
Drum volume (l)
1200
Power (kW)
20.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Door seal or latch wear, typically indicated by water leakage or inability to start
- Drain pump/filter blockage, typically indicated by standing water, slow drain or alarm
- Heating element or thermostat failure, typically indicated by poor washing/drying performance or trip
- Motor, belt or bearing wear, typically indicated by noise, drum not turning or vibration
- Lint/airflow blockage in dryers, typically indicated by long drying times or overheating
Service: Inspect door seals, filters, drains, heating controls, motors, bearings, belts and dryer lint/exhaust paths; verify electrical safety and secure marine mounting.
Spare Parts: Keep door seals, drain pumps, belts, heating elements/thermostats, filters and common control relays appropriate to the installed machines.
Use Cases: Used in crew and passenger laundries on merchant, passenger, offshore and naval vessels. This entry applies specifically to the Tumble Dryer (Marine) variant identified as Electrolux Professional Marine T5350 230V Marine.
T5350 400V Marine
unverified
· 20.0 kW
Capacity (kg)
100
Drum volume (l)
1200
Power (kW)
20.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Door seal or latch wear, typically indicated by water leakage or inability to start
- Drain pump/filter blockage, typically indicated by standing water, slow drain or alarm
- Heating element or thermostat failure, typically indicated by poor washing/drying performance or trip
- Motor, belt or bearing wear, typically indicated by noise, drum not turning or vibration
- Lint/airflow blockage in dryers, typically indicated by long drying times or overheating
Service: Inspect door seals, filters, drains, heating controls, motors, bearings, belts and dryer lint/exhaust paths; verify electrical safety and secure marine mounting.
Spare Parts: Keep door seals, drain pumps, belts, heating elements/thermostats, filters and common control relays appropriate to the installed machines.
Use Cases: Used in crew and passenger laundries on merchant, passenger, offshore and naval vessels. This entry applies specifically to the Tumble Dryer (Marine) variant identified as Electrolux Professional Marine T5350 400V Marine.
T5350 440V Marine
unverified
· 20.0 kW
Capacity (kg)
100
Drum volume (l)
1200
Power (kW)
20.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Door seal or latch wear, typically indicated by water leakage or inability to start
- Drain pump/filter blockage, typically indicated by standing water, slow drain or alarm
- Heating element or thermostat failure, typically indicated by poor washing/drying performance or trip
- Motor, belt or bearing wear, typically indicated by noise, drum not turning or vibration
- Lint/airflow blockage in dryers, typically indicated by long drying times or overheating
Service: Inspect door seals, filters, drains, heating controls, motors, bearings, belts and dryer lint/exhaust paths; verify electrical safety and secure marine mounting.
Spare Parts: Keep door seals, drain pumps, belts, heating elements/thermostats, filters and common control relays appropriate to the installed machines.
Use Cases: Used in crew and passenger laundries on merchant, passenger, offshore and naval vessels. This entry applies specifically to the Tumble Dryer (Marine) variant identified as Electrolux Professional Marine T5350 440V Marine.
T5550 230V Marine
unverified
· 20.0 kW
Capacity (kg)
100
Drum volume (l)
1200
Power (kW)
20.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Door seal or latch wear, typically indicated by water leakage or inability to start
- Drain pump/filter blockage, typically indicated by standing water, slow drain or alarm
- Heating element or thermostat failure, typically indicated by poor washing/drying performance or trip
- Motor, belt or bearing wear, typically indicated by noise, drum not turning or vibration
- Lint/airflow blockage in dryers, typically indicated by long drying times or overheating
Service: Inspect door seals, filters, drains, heating controls, motors, bearings, belts and dryer lint/exhaust paths; verify electrical safety and secure marine mounting.
Spare Parts: Keep door seals, drain pumps, belts, heating elements/thermostats, filters and common control relays appropriate to the installed machines.
Use Cases: Used in crew and passenger laundries on merchant, passenger, offshore and naval vessels. This entry applies specifically to the Tumble Dryer (Marine) variant identified as Electrolux Professional Marine T5550 230V Marine.
T5550 400V Marine
unverified
· 20.0 kW
Capacity (kg)
100
Drum volume (l)
1200
Power (kW)
20.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Door seal or latch wear, typically indicated by water leakage or inability to start
- Drain pump/filter blockage, typically indicated by standing water, slow drain or alarm
- Heating element or thermostat failure, typically indicated by poor washing/drying performance or trip
- Motor, belt or bearing wear, typically indicated by noise, drum not turning or vibration
- Lint/airflow blockage in dryers, typically indicated by long drying times or overheating
Service: Inspect door seals, filters, drains, heating controls, motors, bearings, belts and dryer lint/exhaust paths; verify electrical safety and secure marine mounting.
Spare Parts: Keep door seals, drain pumps, belts, heating elements/thermostats, filters and common control relays appropriate to the installed machines.
Use Cases: Used in crew and passenger laundries on merchant, passenger, offshore and naval vessels. This entry applies specifically to the Tumble Dryer (Marine) variant identified as Electrolux Professional Marine T5550 400V Marine.
T5550 440V Marine
unverified
· 20.0 kW
Capacity (kg)
100
Drum volume (l)
1200
Power (kW)
20.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Door seal or latch wear, typically indicated by water leakage or inability to start
- Drain pump/filter blockage, typically indicated by standing water, slow drain or alarm
- Heating element or thermostat failure, typically indicated by poor washing/drying performance or trip
- Motor, belt or bearing wear, typically indicated by noise, drum not turning or vibration
- Lint/airflow blockage in dryers, typically indicated by long drying times or overheating
Service: Inspect door seals, filters, drains, heating controls, motors, bearings, belts and dryer lint/exhaust paths; verify electrical safety and secure marine mounting.
Spare Parts: Keep door seals, drain pumps, belts, heating elements/thermostats, filters and common control relays appropriate to the installed machines.
Use Cases: Used in crew and passenger laundries on merchant, passenger, offshore and naval vessels. This entry applies specifically to the Tumble Dryer (Marine) variant identified as Electrolux Professional Marine T5550 440V Marine.
Speed Queen Marine
12
ST30 230V Marine
unverified
· 6.0 kW
Capacity (kg)
30
Drum volume (l)
360
Power (kW)
6.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Airflow, water-flow or surface restriction caused by lint, scale, textile residue or blocked filters, resulting in long cycles, poor performance or protective trips
- Heater or temperature-control failure caused by element, sensor or control faults, resulting in no heat, overheating or aborted operation
- Drive-belt, motor, roller or bearing deterioration caused by wear, overloading or misalignment, resulting in noise, poor rotation or stoppage
- Electrical-control faults caused by moisture, loose connections or component failure, resulting in intermittent operation, alarms or breaker trips
- Door, seal, hose or guarding deterioration caused by wear or loosening, resulting in leakage, heat loss or unsafe access
Service: Clean filters, lint paths, drains and accessible heating or roller surfaces appropriate to the installed machine. Inspect bearings, drive components, door or guarding interlocks and electrical connections for wear or overheating. Verify safety interlocks and emergency stop functions where fitted. Keep the machine securely fastened to its marine foundation and inspect anti-vibration mounts. Investigate repeated trips rather than resetting the machine without identifying the cause. Refer to the manufacturer documentation for exact servicing intervals and electrical checks.
Spare Parts: Keep door seals, drive belts where fitted, filters, selected valves or pumps, fuses, heating components and manufacturer-recommended control or sensor parts. High-utilization passenger or offshore accommodation vessels may justify additional wear items. Confirm exact spares from the model and serial number.
Use Cases: Crew, passenger and hotel-service laundry on merchant ships, ferries, cruise vessels and offshore accommodation units.
ST30 400V Marine
unverified
· 6.0 kW
Capacity (kg)
30
Drum volume (l)
360
Power (kW)
6.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Airflow, water-flow or surface restriction caused by lint, scale, textile residue or blocked filters, resulting in long cycles, poor performance or protective trips
- Heater or temperature-control failure caused by element, sensor or control faults, resulting in no heat, overheating or aborted operation
- Drive-belt, motor, roller or bearing deterioration caused by wear, overloading or misalignment, resulting in noise, poor rotation or stoppage
- Electrical-control faults caused by moisture, loose connections or component failure, resulting in intermittent operation, alarms or breaker trips
- Door, seal, hose or guarding deterioration caused by wear or loosening, resulting in leakage, heat loss or unsafe access
Service: Clean filters, lint paths, drains and accessible heating or roller surfaces appropriate to the installed machine. Inspect bearings, drive components, door or guarding interlocks and electrical connections for wear or overheating. Verify safety interlocks and emergency stop functions where fitted. Keep the machine securely fastened to its marine foundation and inspect anti-vibration mounts. Investigate repeated trips rather than resetting the machine without identifying the cause. Refer to the manufacturer documentation for exact servicing intervals and electrical checks.
Spare Parts: Keep door seals, drive belts where fitted, filters, selected valves or pumps, fuses, heating components and manufacturer-recommended control or sensor parts. High-utilization passenger or offshore accommodation vessels may justify additional wear items. Confirm exact spares from the model and serial number.
Use Cases: Crew, passenger and hotel-service laundry on merchant ships, ferries, cruise vessels and offshore accommodation units.
ST30 440V Marine
unverified
· 6.0 kW
Capacity (kg)
30
Drum volume (l)
360
Power (kW)
6.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Airflow, water-flow or surface restriction caused by lint, scale, textile residue or blocked filters, resulting in long cycles, poor performance or protective trips
- Heater or temperature-control failure caused by element, sensor or control faults, resulting in no heat, overheating or aborted operation
- Drive-belt, motor, roller or bearing deterioration caused by wear, overloading or misalignment, resulting in noise, poor rotation or stoppage
- Electrical-control faults caused by moisture, loose connections or component failure, resulting in intermittent operation, alarms or breaker trips
- Door, seal, hose or guarding deterioration caused by wear or loosening, resulting in leakage, heat loss or unsafe access
Service: Clean filters, lint paths, drains and accessible heating or roller surfaces appropriate to the installed machine. Inspect bearings, drive components, door or guarding interlocks and electrical connections for wear or overheating. Verify safety interlocks and emergency stop functions where fitted. Keep the machine securely fastened to its marine foundation and inspect anti-vibration mounts. Investigate repeated trips rather than resetting the machine without identifying the cause. Refer to the manufacturer documentation for exact servicing intervals and electrical checks.
Spare Parts: Keep door seals, drive belts where fitted, filters, selected valves or pumps, fuses, heating components and manufacturer-recommended control or sensor parts. High-utilization passenger or offshore accommodation vessels may justify additional wear items. Confirm exact spares from the model and serial number.
Use Cases: Crew, passenger and hotel-service laundry on merchant ships, ferries, cruise vessels and offshore accommodation units.
ST45 230V Marine
unverified
· 9.0 kW
Capacity (kg)
45
Drum volume (l)
540
Power (kW)
9.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Airflow, water-flow or surface restriction caused by lint, scale, textile residue or blocked filters, resulting in long cycles, poor performance or protective trips
- Heater or temperature-control failure caused by element, sensor or control faults, resulting in no heat, overheating or aborted operation
- Drive-belt, motor, roller or bearing deterioration caused by wear, overloading or misalignment, resulting in noise, poor rotation or stoppage
- Electrical-control faults caused by moisture, loose connections or component failure, resulting in intermittent operation, alarms or breaker trips
- Door, seal, hose or guarding deterioration caused by wear or loosening, resulting in leakage, heat loss or unsafe access
Service: Clean filters, lint paths, drains and accessible heating or roller surfaces appropriate to the installed machine. Inspect bearings, drive components, door or guarding interlocks and electrical connections for wear or overheating. Verify safety interlocks and emergency stop functions where fitted. Keep the machine securely fastened to its marine foundation and inspect anti-vibration mounts. Investigate repeated trips rather than resetting the machine without identifying the cause. Refer to the manufacturer documentation for exact servicing intervals and electrical checks.
Spare Parts: Keep door seals, drive belts where fitted, filters, selected valves or pumps, fuses, heating components and manufacturer-recommended control or sensor parts. High-utilization passenger or offshore accommodation vessels may justify additional wear items. Confirm exact spares from the model and serial number.
Use Cases: Crew, passenger and hotel-service laundry on merchant ships, ferries, cruise vessels and offshore accommodation units.
ST45 400V Marine
unverified
· 9.0 kW
Capacity (kg)
45
Drum volume (l)
540
Power (kW)
9.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Airflow, water-flow or surface restriction caused by lint, scale, textile residue or blocked filters, resulting in long cycles, poor performance or protective trips
- Heater or temperature-control failure caused by element, sensor or control faults, resulting in no heat, overheating or aborted operation
- Drive-belt, motor, roller or bearing deterioration caused by wear, overloading or misalignment, resulting in noise, poor rotation or stoppage
- Electrical-control faults caused by moisture, loose connections or component failure, resulting in intermittent operation, alarms or breaker trips
- Door, seal, hose or guarding deterioration caused by wear or loosening, resulting in leakage, heat loss or unsafe access
Service: Clean filters, lint paths, drains and accessible heating or roller surfaces appropriate to the installed machine. Inspect bearings, drive components, door or guarding interlocks and electrical connections for wear or overheating. Verify safety interlocks and emergency stop functions where fitted. Keep the machine securely fastened to its marine foundation and inspect anti-vibration mounts. Investigate repeated trips rather than resetting the machine without identifying the cause. Refer to the manufacturer documentation for exact servicing intervals and electrical checks.
Spare Parts: Keep door seals, drive belts where fitted, filters, selected valves or pumps, fuses, heating components and manufacturer-recommended control or sensor parts. High-utilization passenger or offshore accommodation vessels may justify additional wear items. Confirm exact spares from the model and serial number.
Use Cases: Crew, passenger and hotel-service laundry on merchant ships, ferries, cruise vessels and offshore accommodation units.
ST45 440V Marine
unverified
· 9.0 kW
Capacity (kg)
45
Drum volume (l)
540
Power (kW)
9.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Airflow, water-flow or surface restriction caused by lint, scale, textile residue or blocked filters, resulting in long cycles, poor performance or protective trips
- Heater or temperature-control failure caused by element, sensor or control faults, resulting in no heat, overheating or aborted operation
- Drive-belt, motor, roller or bearing deterioration caused by wear, overloading or misalignment, resulting in noise, poor rotation or stoppage
- Electrical-control faults caused by moisture, loose connections or component failure, resulting in intermittent operation, alarms or breaker trips
- Door, seal, hose or guarding deterioration caused by wear or loosening, resulting in leakage, heat loss or unsafe access
Service: Clean filters, lint paths, drains and accessible heating or roller surfaces appropriate to the installed machine. Inspect bearings, drive components, door or guarding interlocks and electrical connections for wear or overheating. Verify safety interlocks and emergency stop functions where fitted. Keep the machine securely fastened to its marine foundation and inspect anti-vibration mounts. Investigate repeated trips rather than resetting the machine without identifying the cause. Refer to the manufacturer documentation for exact servicing intervals and electrical checks.
Spare Parts: Keep door seals, drive belts where fitted, filters, selected valves or pumps, fuses, heating components and manufacturer-recommended control or sensor parts. High-utilization passenger or offshore accommodation vessels may justify additional wear items. Confirm exact spares from the model and serial number.
Use Cases: Crew, passenger and hotel-service laundry on merchant ships, ferries, cruise vessels and offshore accommodation units.
ST60 230V Marine
unverified
· 12.0 kW
Capacity (kg)
60
Drum volume (l)
720
Power (kW)
12.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Heating, cooling or drive-component failure causes poor performance, slow cycles or inability to operate
- Temperature sensor, thermostat or control faults cause unstable operation or protective shutdown
- Door seal, hose, drain or valve deterioration causes leakage, heat loss or water accumulation
- Fan, pump, motor or bearing wear causes abnormal noise, reduced circulation or vibration
- Electrical, ignition or safety-interlock faults cause failed starts, nuisance trips or error indications
Service: Inspect seals, controls, heaters or refrigeration components, pumps or fans, water and drain connections, ventilation and secure mounting according to the appliance type. Clean grease, lint, scale or food residues from approved areas. Verify safety interlocks and look for heat-damaged wiring. Refer to the manufacturer documentation for the exact figure for temperature, loading and service criteria.
Spare Parts: Carry seals, sensors, fuses, control relays, pump or fan parts, heating or ignition components and appliance-specific consumables.
Use Cases: Galley, pantry, accommodation and laundry service on merchant, passenger and offshore vessels.
ST60 400V Marine
unverified
· 12.0 kW
Capacity (kg)
60
Drum volume (l)
720
Power (kW)
12.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Heating, cooling or drive-component failure causes poor performance, slow cycles or inability to operate
- Temperature sensor, thermostat or control faults cause unstable operation or protective shutdown
- Door seal, hose, drain or valve deterioration causes leakage, heat loss or water accumulation
- Fan, pump, motor or bearing wear causes abnormal noise, reduced circulation or vibration
- Electrical, ignition or safety-interlock faults cause failed starts, nuisance trips or error indications
Service: Inspect seals, controls, heaters or refrigeration components, pumps or fans, water and drain connections, ventilation and secure mounting according to the appliance type. Clean grease, lint, scale or food residues from approved areas. Verify safety interlocks and look for heat-damaged wiring. Refer to the manufacturer documentation for the exact figure for temperature, loading and service criteria.
Spare Parts: Carry seals, sensors, fuses, control relays, pump or fan parts, heating or ignition components and appliance-specific consumables.
Use Cases: Galley, pantry, accommodation and laundry service on merchant, passenger and offshore vessels.
ST60 440V Marine
unverified
· 12.0 kW
Capacity (kg)
60
Drum volume (l)
720
Power (kW)
12.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Heating, cooling or drive-component failure causes poor performance, slow cycles or inability to operate
- Temperature sensor, thermostat or control faults cause unstable operation or protective shutdown
- Door seal, hose, drain or valve deterioration causes leakage, heat loss or water accumulation
- Fan, pump, motor or bearing wear causes abnormal noise, reduced circulation or vibration
- Electrical, ignition or safety-interlock faults cause failed starts, nuisance trips or error indications
Service: Inspect seals, controls, heaters or refrigeration components, pumps or fans, water and drain connections, ventilation and secure mounting according to the appliance type. Clean grease, lint, scale or food residues from approved areas. Verify safety interlocks and look for heat-damaged wiring. Refer to the manufacturer documentation for the exact figure for temperature, loading and service criteria.
Spare Parts: Carry seals, sensors, fuses, control relays, pump or fan parts, heating or ignition components and appliance-specific consumables.
Use Cases: Galley, pantry, accommodation and laundry service on merchant, passenger and offshore vessels.
ST75 230V Marine
unverified
· 15.0 kW
Capacity (kg)
75
Drum volume (l)
900
Power (kW)
15.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Heating, cooling or drive-component failure causes poor performance, slow cycles or inability to operate
- Temperature sensor, thermostat or control faults cause unstable operation or protective shutdown
- Door seal, hose, drain or valve deterioration causes leakage, heat loss or water accumulation
- Fan, pump, motor or bearing wear causes abnormal noise, reduced circulation or vibration
- Electrical, ignition or safety-interlock faults cause failed starts, nuisance trips or error indications
Service: Inspect seals, controls, heaters or refrigeration components, pumps or fans, water and drain connections, ventilation and secure mounting according to the appliance type. Clean grease, lint, scale or food residues from approved areas. Verify safety interlocks and look for heat-damaged wiring. Refer to the manufacturer documentation for the exact figure for temperature, loading and service criteria.
Spare Parts: Carry seals, sensors, fuses, control relays, pump or fan parts, heating or ignition components and appliance-specific consumables.
Use Cases: Galley, pantry, accommodation and laundry service on merchant, passenger and offshore vessels.
ST75 400V Marine
unverified
· 15.0 kW
Capacity (kg)
75
Drum volume (l)
900
Power (kW)
15.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Heating, cooling or drive-component failure causes poor performance, slow cycles or inability to operate
- Temperature sensor, thermostat or control faults cause unstable operation or protective shutdown
- Door seal, hose, drain or valve deterioration causes leakage, heat loss or water accumulation
- Fan, pump, motor or bearing wear causes abnormal noise, reduced circulation or vibration
- Electrical, ignition or safety-interlock faults cause failed starts, nuisance trips or error indications
Service: Inspect seals, controls, heaters or refrigeration components, pumps or fans, water and drain connections, ventilation and secure mounting according to the appliance type. Clean grease, lint, scale or food residues from approved areas. Verify safety interlocks and look for heat-damaged wiring. Refer to the manufacturer documentation for the exact figure for temperature, loading and service criteria.
Spare Parts: Carry seals, sensors, fuses, control relays, pump or fan parts, heating or ignition components and appliance-specific consumables.
Use Cases: Galley, pantry, accommodation and laundry service on merchant, passenger and offshore vessels.
ST75 440V Marine
unverified
· 15.0 kW
Capacity (kg)
75
Drum volume (l)
900
Power (kW)
15.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Heating, cooling or drive-component failure causes poor performance, slow cycles or inability to operate
- Temperature sensor, thermostat or control faults cause unstable operation or protective shutdown
- Door seal, hose, drain or valve deterioration causes leakage, heat loss or water accumulation
- Fan, pump, motor or bearing wear causes abnormal noise, reduced circulation or vibration
- Electrical, ignition or safety-interlock faults cause failed starts, nuisance trips or error indications
Service: Inspect seals, controls, heaters or refrigeration components, pumps or fans, water and drain connections, ventilation and secure mounting according to the appliance type. Clean grease, lint, scale or food residues from approved areas. Verify safety interlocks and look for heat-damaged wiring. Refer to the manufacturer documentation for the exact figure for temperature, loading and service criteria.
Spare Parts: Carry seals, sensors, fuses, control relays, pump or fan parts, heating or ignition components and appliance-specific consumables.
Use Cases: Galley, pantry, accommodation and laundry service on merchant, passenger and offshore vessels.
JLA Marine
9
JLA TD 16 230V Marine
unverified
· 3.2 kW
Capacity (kg)
16
Drum volume (l)
192
Power (kW)
3.2
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Lint-filter or exhaust blockage causes poor drying, high temperature or protective shutdown
- Heating-element, burner or temperature-control failure causes slow drying or overtemperature trips
- Drum bearing, roller or belt wear causes abnormal noise, poor drum rotation or vibration
- Fan or airflow failure causes damp loads, overheating or long drying cycles
- Door-interlock or control faults cause failure to start, mid-cycle stoppage or error indication
Service: Clean lint filters and exhaust paths frequently and inspect the drum, bearings, drive, fan, heaters, door switch and secure mounting. Check for heat damage and verify overtemperature protection. Ensure ventilation discharge remains unrestricted. Exact temperatures and service limits require manufacturer documentation.
Spare Parts: Carry lint filters, belts or rollers as applicable, door switches, temperature sensors, heating or ignition parts, fan components, fuses and control relays.
Use Cases: Ship laundries on passenger, merchant, naval and offshore vessels.
JLA TD 16 400V Marine
unverified
· 3.2 kW
Capacity (kg)
16
Drum volume (l)
192
Power (kW)
3.2
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Lint-filter or exhaust blockage causes poor drying, high temperature or protective shutdown
- Heating-element, burner or temperature-control failure causes slow drying or overtemperature trips
- Drum bearing, roller or belt wear causes abnormal noise, poor drum rotation or vibration
- Fan or airflow failure causes damp loads, overheating or long drying cycles
- Door-interlock or control faults cause failure to start, mid-cycle stoppage or error indication
Service: Clean lint filters and exhaust paths frequently and inspect the drum, bearings, drive, fan, heaters, door switch and secure mounting. Check for heat damage and verify overtemperature protection. Ensure ventilation discharge remains unrestricted. Exact temperatures and service limits require manufacturer documentation.
Spare Parts: Carry lint filters, belts or rollers as applicable, door switches, temperature sensors, heating or ignition parts, fan components, fuses and control relays.
Use Cases: Ship laundries on passenger, merchant, naval and offshore vessels.
JLA TD 16 440V Marine
unverified
· 3.2 kW
Capacity (kg)
16
Drum volume (l)
192
Power (kW)
3.2
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Lint-filter or exhaust blockage causes poor drying, high temperature or protective shutdown
- Heating-element, burner or temperature-control failure causes slow drying or overtemperature trips
- Drum bearing, roller or belt wear causes abnormal noise, poor drum rotation or vibration
- Fan or airflow failure causes damp loads, overheating or long drying cycles
- Door-interlock or control faults cause failure to start, mid-cycle stoppage or error indication
Service: Clean lint filters and exhaust paths frequently and inspect the drum, bearings, drive, fan, heaters, door switch and secure mounting. Check for heat damage and verify overtemperature protection. Ensure ventilation discharge remains unrestricted. Exact temperatures and service limits require manufacturer documentation.
Spare Parts: Carry lint filters, belts or rollers as applicable, door switches, temperature sensors, heating or ignition parts, fan components, fuses and control relays.
Use Cases: Ship laundries on passenger, merchant, naval and offshore vessels.
JLA TD 22 230V Marine
unverified
· 4.4 kW
Capacity (kg)
22
Drum volume (l)
264
Power (kW)
4.4
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Lint-filter or exhaust blockage causes poor drying, high temperature or protective shutdown
- Heating-element, burner or temperature-control failure causes slow drying or overtemperature trips
- Drum bearing, roller or belt wear causes abnormal noise, poor drum rotation or vibration
- Fan or airflow failure causes damp loads, overheating or long drying cycles
- Door-interlock or control faults cause failure to start, mid-cycle stoppage or error indication
Service: Clean lint filters and exhaust paths frequently and inspect the drum, bearings, drive, fan, heaters, door switch and secure mounting. Check for heat damage and verify overtemperature protection. Ensure ventilation discharge remains unrestricted. Exact temperatures and service limits require manufacturer documentation.
Spare Parts: Carry lint filters, belts or rollers as applicable, door switches, temperature sensors, heating or ignition parts, fan components, fuses and control relays.
Use Cases: Ship laundries on passenger, merchant, naval and offshore vessels.
JLA TD 22 400V Marine
unverified
· 4.4 kW
Capacity (kg)
22
Drum volume (l)
264
Power (kW)
4.4
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Lint-filter or exhaust blockage causes poor drying, high temperature or protective shutdown
- Heating-element, burner or temperature-control failure causes slow drying or overtemperature trips
- Drum bearing, roller or belt wear causes abnormal noise, poor drum rotation or vibration
- Fan or airflow failure causes damp loads, overheating or long drying cycles
- Door-interlock or control faults cause failure to start, mid-cycle stoppage or error indication
Service: Clean lint filters and exhaust paths frequently and inspect the drum, bearings, drive, fan, heaters, door switch and secure mounting. Check for heat damage and verify overtemperature protection. Ensure ventilation discharge remains unrestricted. Exact temperatures and service limits require manufacturer documentation.
Spare Parts: Carry lint filters, belts or rollers as applicable, door switches, temperature sensors, heating or ignition parts, fan components, fuses and control relays.
Use Cases: Ship laundries on passenger, merchant, naval and offshore vessels.
JLA TD 22 440V Marine
unverified
· 4.4 kW
Capacity (kg)
22
Drum volume (l)
264
Power (kW)
4.4
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Lint-filter or exhaust blockage causes poor drying, high temperature or protective shutdown
- Heating-element, burner or temperature-control failure causes slow drying or overtemperature trips
- Drum bearing, roller or belt wear causes abnormal noise, poor drum rotation or vibration
- Fan or airflow failure causes damp loads, overheating or long drying cycles
- Door-interlock or control faults cause failure to start, mid-cycle stoppage or error indication
Service: Clean lint filters and exhaust paths frequently and inspect the drum, bearings, drive, fan, heaters, door switch and secure mounting. Check for heat damage and verify overtemperature protection. Ensure ventilation discharge remains unrestricted. Exact temperatures and service limits require manufacturer documentation.
Spare Parts: Carry lint filters, belts or rollers as applicable, door switches, temperature sensors, heating or ignition parts, fan components, fuses and control relays.
Use Cases: Ship laundries on passenger, merchant, naval and offshore vessels.
JLA TD 35 230V Marine
unverified
· 7.0 kW
Capacity (kg)
35
Drum volume (l)
420
Power (kW)
7.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Lint-filter or exhaust blockage causes poor drying, high temperature or protective shutdown
- Heating-element, burner or temperature-control failure causes slow drying or overtemperature trips
- Drum bearing, roller or belt wear causes abnormal noise, poor drum rotation or vibration
- Fan or airflow failure causes damp loads, overheating or long drying cycles
- Door-interlock or control faults cause failure to start, mid-cycle stoppage or error indication
Service: Clean lint filters and exhaust paths frequently and inspect the drum, bearings, drive, fan, heaters, door switch and secure mounting. Check for heat damage and verify overtemperature protection. Ensure ventilation discharge remains unrestricted. Exact temperatures and service limits require manufacturer documentation.
Spare Parts: Carry lint filters, belts or rollers as applicable, door switches, temperature sensors, heating or ignition parts, fan components, fuses and control relays.
Use Cases: Ship laundries on passenger, merchant, naval and offshore vessels.
JLA TD 35 400V Marine
unverified
· 7.0 kW
Capacity (kg)
35
Drum volume (l)
420
Power (kW)
7.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Lint-filter or exhaust blockage causes poor drying, high temperature or protective shutdown
- Heating-element, burner or temperature-control failure causes slow drying or overtemperature trips
- Drum bearing, roller or belt wear causes abnormal noise, poor drum rotation or vibration
- Fan or airflow failure causes damp loads, overheating or long drying cycles
- Door-interlock or control faults cause failure to start, mid-cycle stoppage or error indication
Service: Clean lint filters and exhaust paths frequently and inspect the drum, bearings, drive, fan, heaters, door switch and secure mounting. Check for heat damage and verify overtemperature protection. Ensure ventilation discharge remains unrestricted. Exact temperatures and service limits require manufacturer documentation.
Spare Parts: Carry lint filters, belts or rollers as applicable, door switches, temperature sensors, heating or ignition parts, fan components, fuses and control relays.
Use Cases: Ship laundries on passenger, merchant, naval and offshore vessels.
JLA TD 35 440V Marine
unverified
· 7.0 kW
Capacity (kg)
35
Drum volume (l)
420
Power (kW)
7.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Lint-filter or exhaust blockage causes poor drying, high temperature or protective shutdown
- Heating-element, burner or temperature-control failure causes slow drying or overtemperature trips
- Drum bearing, roller or belt wear causes abnormal noise, poor drum rotation or vibration
- Fan or airflow failure causes damp loads, overheating or long drying cycles
- Door-interlock or control faults cause failure to start, mid-cycle stoppage or error indication
Service: Clean lint filters and exhaust paths frequently and inspect the drum, bearings, drive, fan, heaters, door switch and secure mounting. Check for heat damage and verify overtemperature protection. Ensure ventilation discharge remains unrestricted. Exact temperatures and service limits require manufacturer documentation.
Spare Parts: Carry lint filters, belts or rollers as applicable, door switches, temperature sensors, heating or ignition parts, fan components, fuses and control relays.
Use Cases: Ship laundries on passenger, merchant, naval and offshore vessels.
Miele Marine
9
PT8253 230V Marine
unverified
· 20.0 kW
Capacity (kg)
100
Drum volume (l)
1200
Power (kW)
20.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Lint-filter or exhaust blockage causes poor drying, high temperature or protective shutdown
- Heating-element, burner or temperature-control failure causes slow drying or overtemperature trips
- Drum bearing, roller or belt wear causes abnormal noise, poor drum rotation or vibration
- Fan or airflow failure causes damp loads, overheating or long drying cycles
- Door-interlock or control faults cause failure to start, mid-cycle stoppage or error indication
Service: Clean lint filters and exhaust paths frequently and inspect the drum, bearings, drive, fan, heaters, door switch and secure mounting. Check for heat damage and verify overtemperature protection. Ensure ventilation discharge remains unrestricted. Exact temperatures and service limits require manufacturer documentation.
Spare Parts: Carry lint filters, belts or rollers as applicable, door switches, temperature sensors, heating or ignition parts, fan components, fuses and control relays.
Use Cases: Ship laundries on passenger, merchant, naval and offshore vessels.
PT8253 400V Marine
unverified
· 20.0 kW
Capacity (kg)
100
Drum volume (l)
1200
Power (kW)
20.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Lint-filter or exhaust blockage causes poor drying, high temperature or protective shutdown
- Heating-element, burner or temperature-control failure causes slow drying or overtemperature trips
- Drum bearing, roller or belt wear causes abnormal noise, poor drum rotation or vibration
- Fan or airflow failure causes damp loads, overheating or long drying cycles
- Door-interlock or control faults cause failure to start, mid-cycle stoppage or error indication
Service: Clean lint filters and exhaust paths frequently and inspect the drum, bearings, drive, fan, heaters, door switch and secure mounting. Check for heat damage and verify overtemperature protection. Ensure ventilation discharge remains unrestricted. Exact temperatures and service limits require manufacturer documentation.
Spare Parts: Carry lint filters, belts or rollers as applicable, door switches, temperature sensors, heating or ignition parts, fan components, fuses and control relays.
Use Cases: Ship laundries on passenger, merchant, naval and offshore vessels.
PT8253 440V Marine
unverified
· 20.0 kW
Capacity (kg)
100
Drum volume (l)
1200
Power (kW)
20.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Lint-filter or exhaust blockage causes poor drying, high temperature or protective shutdown
- Heating-element, burner or temperature-control failure causes slow drying or overtemperature trips
- Drum bearing, roller or belt wear causes abnormal noise, poor drum rotation or vibration
- Fan or airflow failure causes damp loads, overheating or long drying cycles
- Door-interlock or control faults cause failure to start, mid-cycle stoppage or error indication
Service: Clean lint filters and exhaust paths frequently and inspect the drum, bearings, drive, fan, heaters, door switch and secure mounting. Check for heat damage and verify overtemperature protection. Ensure ventilation discharge remains unrestricted. Exact temperatures and service limits require manufacturer documentation.
Spare Parts: Carry lint filters, belts or rollers as applicable, door switches, temperature sensors, heating or ignition parts, fan components, fuses and control relays.
Use Cases: Ship laundries on passenger, merchant, naval and offshore vessels.
PT8333 230V Marine
unverified
· 20.0 kW
Capacity (kg)
100
Drum volume (l)
1200
Power (kW)
20.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Lint-filter or exhaust blockage causes poor drying, high temperature or protective shutdown
- Heating-element, burner or temperature-control failure causes slow drying or overtemperature trips
- Drum bearing, roller or belt wear causes abnormal noise, poor drum rotation or vibration
- Fan or airflow failure causes damp loads, overheating or long drying cycles
- Door-interlock or control faults cause failure to start, mid-cycle stoppage or error indication
Service: Clean lint filters and exhaust paths frequently and inspect the drum, bearings, drive, fan, heaters, door switch and secure mounting. Check for heat damage and verify overtemperature protection. Ensure ventilation discharge remains unrestricted. Exact temperatures and service limits require manufacturer documentation.
Spare Parts: Carry lint filters, belts or rollers as applicable, door switches, temperature sensors, heating or ignition parts, fan components, fuses and control relays.
Use Cases: Ship laundries on passenger, merchant, naval and offshore vessels.
PT8333 400V Marine
unverified
· 20.0 kW
Capacity (kg)
100
Drum volume (l)
1200
Power (kW)
20.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Lint-filter or exhaust blockage causes poor drying, high temperature or protective shutdown
- Heating-element, burner or temperature-control failure causes slow drying or overtemperature trips
- Drum bearing, roller or belt wear causes abnormal noise, poor drum rotation or vibration
- Fan or airflow failure causes damp loads, overheating or long drying cycles
- Door-interlock or control faults cause failure to start, mid-cycle stoppage or error indication
Service: Clean lint filters and exhaust paths frequently and inspect the drum, bearings, drive, fan, heaters, door switch and secure mounting. Check for heat damage and verify overtemperature protection. Ensure ventilation discharge remains unrestricted. Exact temperatures and service limits require manufacturer documentation.
Spare Parts: Carry lint filters, belts or rollers as applicable, door switches, temperature sensors, heating or ignition parts, fan components, fuses and control relays.
Use Cases: Ship laundries on passenger, merchant, naval and offshore vessels.
PT8333 440V Marine
unverified
· 20.0 kW
Capacity (kg)
100
Drum volume (l)
1200
Power (kW)
20.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Lint-filter or exhaust blockage causes poor drying, high temperature or protective shutdown
- Heating-element, burner or temperature-control failure causes slow drying or overtemperature trips
- Drum bearing, roller or belt wear causes abnormal noise, poor drum rotation or vibration
- Fan or airflow failure causes damp loads, overheating or long drying cycles
- Door-interlock or control faults cause failure to start, mid-cycle stoppage or error indication
Service: Clean lint filters and exhaust paths frequently and inspect the drum, bearings, drive, fan, heaters, door switch and secure mounting. Check for heat damage and verify overtemperature protection. Ensure ventilation discharge remains unrestricted. Exact temperatures and service limits require manufacturer documentation.
Spare Parts: Carry lint filters, belts or rollers as applicable, door switches, temperature sensors, heating or ignition parts, fan components, fuses and control relays.
Use Cases: Ship laundries on passenger, merchant, naval and offshore vessels.
PT8403 230V Marine
unverified
· 20.0 kW
Capacity (kg)
100
Drum volume (l)
1200
Power (kW)
20.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Lint-filter or exhaust blockage causes poor drying, high temperature or protective shutdown
- Heating-element, burner or temperature-control failure causes slow drying or overtemperature trips
- Drum bearing, roller or belt wear causes abnormal noise, poor drum rotation or vibration
- Fan or airflow failure causes damp loads, overheating or long drying cycles
- Door-interlock or control faults cause failure to start, mid-cycle stoppage or error indication
Service: Clean lint filters and exhaust paths frequently and inspect the drum, bearings, drive, fan, heaters, door switch and secure mounting. Check for heat damage and verify overtemperature protection. Ensure ventilation discharge remains unrestricted. Exact temperatures and service limits require manufacturer documentation.
Spare Parts: Carry lint filters, belts or rollers as applicable, door switches, temperature sensors, heating or ignition parts, fan components, fuses and control relays.
Use Cases: Ship laundries on passenger, merchant, naval and offshore vessels.
PT8403 400V Marine
unverified
· 20.0 kW
Capacity (kg)
100
Drum volume (l)
1200
Power (kW)
20.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Lint-filter or exhaust blockage causes poor drying, high temperature or protective shutdown
- Heating-element, burner or temperature-control failure causes slow drying or overtemperature trips
- Drum bearing, roller or belt wear causes abnormal noise, poor drum rotation or vibration
- Fan or airflow failure causes damp loads, overheating or long drying cycles
- Door-interlock or control faults cause failure to start, mid-cycle stoppage or error indication
Service: Clean lint filters and exhaust paths frequently and inspect the drum, bearings, drive, fan, heaters, door switch and secure mounting. Check for heat damage and verify overtemperature protection. Ensure ventilation discharge remains unrestricted. Exact temperatures and service limits require manufacturer documentation.
Spare Parts: Carry lint filters, belts or rollers as applicable, door switches, temperature sensors, heating or ignition parts, fan components, fuses and control relays.
Use Cases: Ship laundries on passenger, merchant, naval and offshore vessels.
PT8403 440V Marine
unverified
· 20.0 kW
Capacity (kg)
100
Drum volume (l)
1200
Power (kW)
20.0
Water consumption (l)
0
Spin speed (1/min)
0
Common Failures & Inspection Points
- Lint-filter or exhaust blockage causes poor drying, high temperature or protective shutdown
- Heating-element, burner or temperature-control failure causes slow drying or overtemperature trips
- Drum bearing, roller or belt wear causes abnormal noise, poor drum rotation or vibration
- Fan or airflow failure causes damp loads, overheating or long drying cycles
- Door-interlock or control faults cause failure to start, mid-cycle stoppage or error indication
Service: Clean lint filters and exhaust paths frequently and inspect the drum, bearings, drive, fan, heaters, door switch and secure mounting. Check for heat damage and verify overtemperature protection. Ensure ventilation discharge remains unrestricted. Exact temperatures and service limits require manufacturer documentation.
Spare Parts: Carry lint filters, belts or rollers as applicable, door switches, temperature sensors, heating or ignition parts, fan components, fuses and control relays.
Use Cases: Ship laundries on passenger, merchant, naval and offshore vessels.