OceanSphereENGINES
Library› Engine Room› Turbochargers› Turbocharger› Kawasaki (KBB) Type HPR4500

Type HPR4500

Turbocharger · Turbochargers

Technical data from manufacturer or class sources · not yet verified by a person​‍​‍⁠⁠​⁠‍⁠‌‍‍​‌⁠​‍​​

Kawasaki KBB-Type HPR4500 — KBB-Type, 6500 kW max.

Specifications

Technical data.reference — unverified

Do you have the manufacturer datasheet for this model? Send it with the enquiry form — we check it and name the source.

Frame SizeHPR4500
Power max (kW)6500
Inspection

Inspector Detail ✓ verified

Common issues

  • Bearing wear (journal and thrust bearings) due to high rotational speeds and thermal loads, leading to excessive axial/radial play and potential rotor contact.
  • Compressor wheel fouling or erosion, reducing efficiency and potentially causing imbalance, especially with poor air filtration.
  • Turbine wheel and nozzle ring fouling or erosion from exhaust gas impurities (e.g., heavy fuel oil combustion byproducts), leading to reduced power and surging.
  • Oil leakage from bearing housings, often due to worn oil seals, clogged drain lines, or incorrect sealing air pressure.
  • Rotor imbalance causing excessive vibration, which can lead to bearing damage, shaft fatigue, and even rotor burst.
  • Cracks in turbine casing or exhaust gas inlet/outlet ducts due to thermal cycling and stress.
  • Surging, often an operational issue, but can cause severe mechanical stress and damage to compressor and turbine blades if prolonged.
  • Damage to insulation blankets, leading to heat radiation and potential fire hazards.

Inspection checklist

  • Check axial and radial play of the rotor shaft (cold and hot if possible) to assess bearing condition. Compare with manufacturer's limits.
  • Visually inspect compressor and turbine wheels for fouling, erosion, foreign object damage (FOD), and blade tip rub marks. Ensure blades are clean and intact.
  • Inspect nozzle ring and diffuser for cracks, deformation, or excessive carbon buildup.
  • Check for any signs of oil leakage around bearing housings, oil supply/drain lines, and casing joints. Verify oil drain lines are clear.
  • Examine the turbocharger casing for cracks, loose bolts, and integrity of insulation blankets.
  • Verify the condition of the air filter upstream of the compressor; a dirty filter significantly impacts performance and can cause compressor damage.
  • Monitor lube oil pressure and temperature at the turbocharger inlet and outlet during operation. Check for abnormal pressure drops or temperature increases.
  • Listen for unusual noises (whining, grinding, rubbing) and observe vibration levels during engine operation.
  • Inspect the condition of the exhaust gas expansion joint and connections for leaks or damage.

Service intervals

Minor Inspection (visual, operational checks)1,000 - 2,000 running hours
Intermediate Inspection (bearing inspection, cleaning of compressor/turbine)4,000 - 8,000 running hours
Major Overhaul (complete disassembly, inspection, replacement of wear parts, rotor balancing)12,000 - 18,000 running hours
Bearing Replacement (journal and thrust bearings)8,000 - 16,000 running hours (or as condition dictates)
Nozzle Ring/Diffuser Inspection/Cleaning4,000 - 8,000 running hours

Typical wear limits

Axial Play (rotor shaft)New: 0.15 - 0.30 mm; Max Service Limit: 0.40 - 0.60 mm (consult specific manual)
Radial Play (rotor shaft)New: 0.05 - 0.15 mm; Max Service Limit: 0.20 - 0.30 mm (consult specific manual)
Compressor/Turbine Blade Tip ClearanceIncrease of >0.10 mm from new specification indicates wear or casing distortion.
Bearing Shell ThicknessMax wear typically 5-10% reduction from new thickness, or as per manufacturer's specific gauge.
Shaft Runout (after disassembly)Max allowable: < 0.02 mm (measured at bearing journals).

Ranges are typical for this design class. Always confirm against the manufacturer documentation for your serial number.

Critical spares

  • Complete bearing cartridge assembly (journal and thrust bearings)
  • Oil sealing rings / labyrinth seals
  • Full gasket and O-ring set for overhaul
  • Lube oil filter elements (if applicable to turbocharger's dedicated system)
  • Nozzle ring segments or complete nozzle ring (depending on design and common failure modes)
  • Special tools for disassembly/assembly (e.g., rotor lifting tools, bearing pullers)
  • Compressor cleaning fluid / turbine washing chemicals

Safety

  • High surface temperatures (exhaust casing can exceed 400°C) posing severe burn risks. Ensure insulation is intact and personnel are aware.
  • High rotational speeds (up to 50,000 - 70,000 RPM for this size) present a catastrophic rotor burst hazard if severe imbalance or material failure occurs.
  • Pressurized systems (exhaust gas, charge air, lube oil) require proper depressurization before any maintenance to prevent injury.
  • Hot lube oil spray or leakage can create a fire hazard, especially in the vicinity of hot exhaust components.
  • High noise levels during operation necessitate hearing protection in the engine room.

Class survey

Class surveyors typically verify the turbocharger's operational parameters (speed, temperatures, pressures) against design limits. They will review maintenance records, including logbook entries for running hours, service reports, and any repairs. External inspection focuses on oil/gas leakage, casing integrity, insulation condition, and overall cleanliness. They check for excessive vibration, proper functioning of safety devices (e.g., overspeed trip), and the availability of critical spare parts onboard. Accessibility for inspection and maintenance is also considered.

Estimated lifetime: 100,000+ hours (with regular maintenance and scheduled major overhauls every 12,000 - 18,000 hours)

Need this part?

Request a quote for this model.

Free of charge — send us your request for Kawasaki (KBB) equipment. Our team checks it and replies by e-mail.

For marine equipment hardly any maker or authorised dealer will name a price while the vessel is unknown. With the vessel details, availability and price can be settled faster; without them we may have to ask first, which costs a few days. If you are not allowed to name the vessel, a photo of the rating plate is enough — attach it below or send it as a reply to our confirmation e-mail.

Your contact details are not published. No account required.
Related models

Also in Turbocharger.

Other models of the same equipment type, Kawasaki (KBB) first.

By manufacturer ABBMAN Energy SolutionsIHIMitsubishiABB Turbocharging / AccelleronKawasakiPBSTCummins Holset TurbochargersNapierMAN ES TurbochargingMitsubishi METGarrett Motion MarineVolvo PentaKBB TurboKompressorenbau BannewitzAll manufacturersSpare parts by equipmentNew here? Create a free account Can't read the plate? Try the nameplate scanner All Kawasaki (KBB) models More like KBB-Type HPR4500
More than the data sheet shows

We answer by e-mail, never with an automatic reply.

Tell us what you need for this Kawasaki (KBB) Type HPR4500 — a part, a service call, a second opinion. Are you Kawasaki (KBB)? Claim this brand page.

Service engineer? Write the day report for this Type HPR4500 in OceanSphere Work — photos, hours and parts, as a PDF for the owner. Try it free for 14 days →

Frequently asked

Questions that come up with this equipment.

Is this model's data free?

Yes. Specifications, documents and service notes for this model are readable without an account. An account adds saved searches and requests, nothing is taken away.

Can you find a part for this exact model?

Yes. Tell us the manufacturer, the model and what you need — a person reads every request and replies by e-mail.

The specifications look wrong — what now?

Send us the nameplate or the correct value. We check it against the manufacturer datasheet or class-society record and update the page.