OceanSphereENGINES
Library› Engine Room› Turbochargers› Turbocharger› Kawasaki (KBB) A ST31-A

A ST31-A

Turbocharger · Turbochargers

Technical data from manufacturer or class sources · not yet verified by a person​‍​‍⁠⁠​⁠​⁠‍‌​‌⁠⁠⁠‌‌‌

Kawasaki KBB-A ST31-A — KBB-A, 6000 kW max.

Specifications

Technical data.reference — unverified

Do you have the manufacturer datasheet for this model? Send it with the enquiry form — we check it and name the source.

Frame SizeST31-A
Power max (kW)6000
Inspection

Inspector Detail ✓ verified

Common issues

  • Bearing wear (axial and radial play exceeding limits) due to contaminated oil or high load cycles.
  • Compressor and/or turbine fouling, leading to reduced efficiency, surging, and increased exhaust gas temperatures.
  • Exhaust gas leaks from casing joints, expansion bellows, or turbine inlet/outlet connections.
  • Oil leaks from bearing housing seals, often visible at the compressor or turbine end drains.
  • Rotor imbalance or damage (e.g., bent shaft, chipped blades) causing excessive vibration and noise.
  • Cracks in turbine casing or nozzle ring due to thermal stress or material fatigue.
  • Surging, particularly at low engine loads or during rapid load changes, indicating compressor instability or fouling.
  • Failure of water washing system components (if fitted), leading to ineffective cleaning.

Inspection checklist

  • Check rotor axial and radial play (free play) against manufacturer's limits using a dial gauge.
  • Inspect compressor and turbine blades for fouling, erosion, impact damage, and cracks (visual inspection, boroscope if necessary).
  • Verify integrity of all casing joints, expansion bellows, and insulation for signs of exhaust gas or oil leaks.
  • Check bearing housing drain lines for obstructions and proper oil flow/drainage.
  • Monitor turbocharger speed, boost pressure, and exhaust gas temperatures (inlet/outlet) for deviations from normal operating parameters.
  • Listen for unusual noises (whining, grinding, rubbing) and check for excessive vibration during operation.
  • Inspect air filter elements (if applicable) for cleanliness and damage.
  • Verify proper operation of the water washing system (if fitted) and check nozzle condition.

Service intervals

Minor Inspection (visual, cleaning, operational check)1,000 - 2,000 running hours
Bearing Inspection/Replacement (axial & radial bearings)8,000 - 12,000 running hours
Major Overhaul (rotor removal, cleaning, balancing, casing inspection)16,000 - 24,000 running hours
Turbine Casing Inspection (thermal cracks)Every 16,000 - 24,000 running hours

Typical wear limits

Rotor Axial Play (new)0.15 - 0.35 mm
Rotor Axial Play (max allowable)0.50 - 0.70 mm
Rotor Radial Play (new)0.05 - 0.15 mm
Rotor Radial Play (max allowable)0.20 - 0.30 mm
Compressor/Turbine Blade ErosionVisual inspection for significant material loss, pitting, or cracks. Manufacturer's manual specifies acceptable damage limits.
Bearing Shell ThicknessMeasured against manufacturer's specified minimum thickness; typically replaced if wear exceeds 0.05-0.10 mm from new.

Ranges are typical for this design class. Always confirm against the manufacturer documentation for your serial number.

Critical spares

  • Complete set of bearing components (thrust bearing, radial bearings, O-rings, seals)
  • Gasket and O-ring sets for casing joints and inspection covers
  • Oil inlet/outlet pipe gaskets and sealing rings
  • Water washing nozzles (if applicable)
  • Shaft sealing rings (compressor and turbine side)
  • Air filter elements (if applicable)
  • Set of securing bolts and nuts for critical connections (e.g., casing halves)

Safety

  • High surface temperatures (up to 400-600°C) of the turbine casing and exhaust pipes, requiring proper insulation and caution.
  • High-speed rotating components (up to 30,000-50,000 RPM) pose a severe hazard during maintenance or if containment fails.
  • Pressurized exhaust gas and charge air systems (up to 4-5 bar), requiring depressurization before opening.
  • Potential for hot oil spray or exhaust gas release during inspection or maintenance if seals/gaskets fail.
  • Noise levels can be very high; hearing protection is mandatory in the vicinity of operating turbochargers.

Class survey

Class surveyors typically verify the following: operational performance (boost pressure, temperatures, speed), absence of abnormal noise/vibration, integrity of casing and insulation (no leaks, no hot spots), condition of safety devices (e.g., overspeed trip if fitted, though less common on modern units), proper maintenance records (including bearing replacements, cleaning, and overhauls), and compliance with manufacturer's service recommendations. They may request to witness rotor free play measurements or inspect internal components if there are concerns about performance or condition.

Estimated lifetime: 32,000 - 48,000 running hours (before major component replacement like rotor shaft or full unit replacement, assuming regular maintenance and overhauls)

Need this part?

Request a quote for this model.

Free of charge — send us your request for Kawasaki (KBB) equipment. Our team checks it and replies by e-mail.

For marine equipment hardly any maker or authorised dealer will name a price while the vessel is unknown. With the vessel details, availability and price can be settled faster; without them we may have to ask first, which costs a few days. If you are not allowed to name the vessel, a photo of the rating plate is enough — attach it below or send it as a reply to our confirmation e-mail.

Your contact details are not published. No account required.
Related models

Also in Turbocharger.

Other models of the same equipment type, Kawasaki (KBB) first.

By manufacturer ABBMAN Energy SolutionsIHIMitsubishiABB Turbocharging / AccelleronKawasakiPBSTCummins Holset TurbochargersNapierMAN ES TurbochargingMitsubishi METGarrett Motion MarineVolvo PentaKBB TurboKompressorenbau BannewitzAll manufacturersSpare parts by equipmentNew here? Create a free account Can't read the plate? Try the nameplate scanner All Kawasaki (KBB) models More like KBB-A ST31-A
More than the data sheet shows

We answer by e-mail, never with an automatic reply.

Tell us what you need for this Kawasaki (KBB) A ST31-A — a part, a service call, a second opinion. Are you Kawasaki (KBB)? Claim this brand page.

Service engineer? Write the day report for this A ST31-A in OceanSphere Work — photos, hours and parts, as a PDF for the owner. Try it free for 14 days →

Frequently asked

Questions that come up with this equipment.

Is this model's data free?

Yes. Specifications, documents and service notes for this model are readable without an account. An account adds saved searches and requests, nothing is taken away.

Can you find a part for this exact model?

Yes. Tell us the manufacturer, the model and what you need — a person reads every request and replies by e-mail.

The specifications look wrong — what now?

Send us the nameplate or the correct value. We check it against the manufacturer datasheet or class-society record and update the page.