Towing Bracket
A towing bracket is the structural padeye welded into bow and stern that receives the towing pennant during an emergency tow; on tankers above 20,000 dwt it is part of a SOLAS-mandated arrangement that must be usable within minutes, not rigged from scratch.
Read more — Towing Bracket explained ▾
What sets a towing bracket apart
A towing bracket is not a general-purpose padeye pressed into service for towing. It is a purpose-built structural fitting, calculated against the ship's design towing force and welded into doubler plates that spread the load into deck girders and shell framing rather than into a single deck plate. The distinction matters because an emergency tow can apply loads far above anything a mooring bitt or Panama lead was designed to absorb, and a fitting that looks similar but was never stressed for towing will tear out of the deck under load. On tankers the bracket is one element of the Emergency Towing Arrangement (ETA), a fitted, ready-to-use system rather than a piece of loose gear kept in a locker.
Main components
Bracket and padeye
A heavy fabricated bracket, usually a closed-eye or double-plate padeye, through-bolted or welded to reinforced deck structure at bow and stern. The pin diameter and plate thickness are sized from the calculated towing force, not from a standard mooring fitting table.
Fairlead
Guides the towing pennant from the bracket over the bow or stern without a sharp bend that would fatigue the wire or chain. Fairlead radius and roller diameter are matched to the pennant size.
Chain stopper
Takes the strain off the winch or bitts once the pennant is made fast, holding the load on the chain link rather than on rotating machinery.
Pick-up gear
A retrieval line, buoy, or messenger arrangement that lets the towing vessel's crew recover the pennant from a disabled ship without launching a boat, which is the entire point of a pre-rigged ETA in bad weather.
Sizing and selection
The bracket's design load is derived from the ship's deadweight using the formula in the SOLAS towing arrangement requirements, then increased by a safety factor before the bracket, fairlead, and chain stopper are each checked against it. Selection also depends on:
- Deck layout at bow and stern, and whether existing structure can take a doubler without major steelwork.
- Pennant material and diameter, since the fairlead and stopper must match it.
- Corrosion allowance, because the bracket sits in one of the most exposed, spray-soaked positions on the ship.
- Access for inspection without removing other deck fittings.
Regulations and class
SOLAS Chapter II-1 requires tankers of 20,000 dwt and above to carry a fitted emergency towing arrangement at both ends, capable of being deployed within 15 minutes in bad weather and within 1 hour in favourable conditions without help from the towing ship. Class societies survey the bracket and associated fittings as part of the periodic hull survey, checking weld condition, pin wear, and that the pick-up gear is still present and led correctly, since these arrangements are rarely used and easily neglected.
Typical faults
| Fault | Consequence |
|---|---|
| Corrosion at the bracket-to-deck weld, hidden under paint | Reduced load capacity that only shows up under actual towing load, by which point failure is sudden |
| Pick-up gear missing or perished | Deployment time far exceeds the SOLAS limit, forcing a boat launch in weather that may not allow it |
| Fairlead roller seized | Pennant chafes against a fixed edge instead of running free, cutting through wire strands under load |
| Chain stopper never load-tested after installation | Stopper slips under real towing tension, transferring shock load to the winch brake |
What to look for in a supplier
- Design calculations referencing the actual ship's deadweight and the applicable SOLAS formula, not a generic catalogue bracket.
- Weld procedure and NDT records for the bracket-to-hull connection, since this is a fatigue-loaded structural joint.
- Class approval or a type approval certificate covering the complete ETA, not just the bracket in isolation.
- Compatibility of fairlead and chain stopper dimensions with the pennant already carried on board.
During drills, actually run the pennant through the fairlead and onto the chain stopper rather than just confirming the bracket is there — a seized fairlead or a stopper that has never been worked is the failure that shows up first when the arrangement is needed for real.
9 manufacturers · 19 models
China National Shipbuilding Equipment & Materials (East China)
5Dae Heung Marine
3Generic (Class Approved)
3- Corrosion, wastage or coating breakdown causes visible section loss and weakens the fitting or surrounding structure
- Wear in pins, rollers, hinges or bearing surfaces causes excessive play, stiffness or poor line guidance
- Seal or gasket deterioration on closing appliances causes water ingress or loss of weathertight integrity
- Loose foundations, fasteners or cracked welds cause movement, vibration or visible structural defects
- Blocked drains, vents or passages cause water accumulation, pressure problems or restricted operation
- SOLAS‑compliant design accepted by most classification societies
- Forward placement gives optimal angle for towing forces on loss of propulsion
- Class‑approved welds and pins simplify installation on new builds or during retrofits
- Simple mechanical operation – manual release pin can be exercised annually
- Weld cracks have been reported if not inspected at dry‑dock, requiring NDT verification
- Pins are prone to seizure in high‑salinity or poorly maintained environments
- Chafing plates wear over time and must be replaced periodically
- Limited adjustability – fixed forward orientation may not suit vessels with unconventional bow layouts
- Corrosion, wastage or coating breakdown causes visible section loss and weakens the fitting or surrounding structure
- Wear in pins, rollers, hinges or bearing surfaces causes excessive play, stiffness or poor line guidance
- Seal or gasket deterioration on closing appliances causes water ingress or loss of weathertight integrity
- Loose foundations, fasteners or cracked welds cause movement, vibration or visible structural defects
- Blocked drains, vents or passages cause water accumulation, pressure problems or restricted operation
- SOLAS compliant and class approved, meeting mandatory safety standards
- Simple manual operation – no hydraulic or powered components required
- Robust steel construction suitable for high‑impact loads
- Easy visual inspection of pennant wire and stopper mechanism
- Aft placement aligns directly with the vessel’s longitudinal axis for efficient towing
- Load rating may be lower than specialised high‑strength custom brackets
- Pennant wire is prone to corrosion if not inspected and maintained annually
- Manual stopper can seize under extreme load or if debris accumulates
- Foundation stresses must be monitored; improper mounting can lead to bracket failure
- Corrosion, wastage or coating breakdown causes visible section loss and weakens the fitting or surrounding structure
- Wear in pins, rollers, hinges or bearing surfaces causes excessive play, stiffness or poor line guidance
- Seal or gasket deterioration on closing appliances causes water ingress or loss of weathertight integrity
- Loose foundations, fasteners or cracked welds cause movement, vibration or visible structural defects
- Blocked drains, vents or passages cause water accumulation, pressure problems or restricted operation
- Class approved and SOLAS‑compliant for tanker applications
- High rated load capacity suitable for large vessels (>20 000 DWT)
- Standard quick‑release pin enables rapid connection of towlines
- Designed for semi‑annual inspection with clear access to critical joints
- Historical reports of weld cracking at the deck attachment area
- Pin corrosion can lead to seizure if maintenance is lax
- Cover plate may be prone to damage from impact or improper handling
- Installation often requires reinforcement of the deck structure
Tanktech
3DHMC Co., Ltd. (Yeongam Factory)
1Foshan Daxiang Marine Equipment
1Jiangsu Xingyang Marine Equipment Making
1KTMI
1