OceanSphereENGINES

8H27/38

Main Engine 4-Stroke · Main Engines (4-Stroke)

Technical data from manufacturer or class sources · not yet verified by a person​‍​‍⁠‌⁠⁠‌‌‌​‌​‍⁠‌​​‌
8Cylinders
270 mmBore
380 mmStroke

The HiMSEN 8H27/38 is an 8‑cylinder inline four‑stroke main engine delivering 2 920 kW at 800 rpm, featuring common‑rail fuel injection and dual‑fuel capability (HFO/MGO) for Tier II emission compliance.

Specifications

Technical data.reference — unverified

Do you have the manufacturer datasheet for this model? Send it with the enquiry form — we check it and name the source.

ConfigurationL
Speed (rpm)800
Fuel TypeHFO/MGO
TechnologyCommon Rail Tier II
Inspection

Inspector Detail ✓ verified

Common issues

  • Common Rail Injector Malfunctions: Clogging, tip erosion, leakage, or sticking due to HFO quality or prolonged operation, leading to poor combustion, high exhaust temperatures, and increased fuel consumption.
  • High-Pressure Fuel Pump Issues: Wear of plungers/barrels, control valve failures, or pressure fluctuations affecting fuel delivery and engine performance.
  • Exhaust Valve Burning/Sticking: Particularly when operating on HFO, due to vanadium/sodium deposits, poor combustion, or inadequate valve rotators/lubrication, leading to loss of compression and power.
  • Turbocharger Fouling/Damage: Deposits from HFO combustion on turbine blades and nozzle rings, or bearing wear, reducing efficiency and boost pressure.
  • Cylinder Liner/Piston Ring Wear: Accelerated wear due to abrasive particles in fuel/lube oil, poor combustion, or inadequate lubrication, leading to increased blow-by and lube oil consumption.
  • Fuel System Contamination: Water or particulate matter in HFO causing damage to fine-tolerance common rail components and filters.
  • Bearing Wear (Main/Conrod): Due to lube oil degradation, contamination, or insufficient oil film, leading to abnormal noise, vibration, and potential catastrophic failure.

Inspection checklist

  • Visual Leakage Check: Inspect all fuel lines (especially HP lines), lube oil lines, cooling water pipes, and exhaust manifold for any signs of leakage.
  • Exhaust Gas Temperature Monitoring: Compare cylinder-wise exhaust gas temperatures for uniformity; significant deviations indicate combustion issues (injectors, valves).
  • Crankcase Blow-by Measurement: Monitor blow-by rates (e.g., via crankcase pressure or flow meter) to assess piston ring and liner condition.
  • Fuel System Pressure & Filter DP: Verify common rail pressure stability, fuel supply pressure, and differential pressure across fuel filters (primary, secondary, HP).
  • Lube Oil Analysis & Pressure/Temperature: Review recent lube oil analysis reports (TBN, viscosity, wear metals, water content) and check engine lube oil pressure/temperature.
  • Turbocharger Condition: Check axial/radial play of the rotor, inspect turbine/compressor blades for fouling or damage, and monitor boost pressure.
  • Safety Device Functionality: Periodically test overspeed trip, low lube oil pressure shutdown, and high cooling water temperature shutdown.
  • Engine Performance Parameters: Log and trend power output, specific fuel oil consumption (SFOC), fuel rack position, and charge air pressure/temperature.
  • Cylinder Head Component Inspection: During scheduled maintenance, inspect injectors, exhaust valves, and valve seats for wear, deposits, or damage.

Service intervals

Lube Oil & Filter Change250-500 hours (or as per oil analysis)
Fuel Filter Elements (Primary/Secondary)250-500 hours
Common Rail Injector Overhaul/Replacement4,000-8,000 hours
Cylinder Head Overhaul (Valves, Seats, Springs)8,000-12,000 hours
Piston & Connecting Rod Overhaul12,000-16,000 hours
Turbocharger Minor Overhaul4,000-8,000 hours
Turbocharger Major Overhaul12,000-16,000 hours
Main & Connecting Rod Bearing Inspection/Renewal16,000-24,000 hours
High-Pressure Fuel Pump Overhaul8,000-12,000 hours

Typical wear limits

Cylinder Liner Wear (Max Taper/Ovality)0.6 - 0.8 mm (max allowable)
Piston Ring Groove Clearance (Axial)0.15 - 0.25 mm (new ring in worn groove)
Crankshaft Deflection (Max Deviation)0.05 - 0.10 mm (across all webs)
Main Bearing Clearance0.18 - 0.25 mm (max allowable)
Connecting Rod Bearing Clearance0.15 - 0.22 mm (max allowable)
Exhaust Valve Seat Recession0.8 - 1.2 mm (from original position)
Turbocharger Rotor Axial Play0.10 - 0.20 mm (max allowable)
Turbocharger Rotor Radial Play0.20 - 0.40 mm (max allowable)

Ranges are typical for this design class. Always confirm against the manufacturer documentation for your serial number.

Critical spares

  • Common Rail Injector Assembly: At least one complete set or critical components for immediate replacement.
  • High-Pressure Fuel Pump Repair Kit / Element: For quick repair of the HP pump.
  • Fuel Filter Elements (all stages): Sufficient stock for several changes.
  • Lube Oil Filter Elements: Sufficient stock for several changes.
  • Exhaust Valve Spindles & Seats: At least one set per cylinder.
  • Piston Rings: One complete set per cylinder.
  • Connecting Rod Bearings (Upper & Lower): One set.
  • Assorted Gaskets & O-rings: Especially for fuel, lube oil, and cooling systems.
  • Critical Sensors: Lube oil pressure, cooling water temperature, engine speed, common rail pressure.

Safety

  • High-Pressure Fuel Leaks: Common Rail systems operate at extremely high pressures (up to 2000+ bar). Leaks can cause severe skin penetration injuries or atomized fuel spray, posing a significant fire hazard.
  • Hot Surfaces: Exhaust manifold, turbocharger, and other engine components operate at high temperatures, posing burn risks. Ensure insulation is intact.
  • Rotating Machinery: Flywheel, crankshaft, and coupling present entanglement hazards. Ensure guards are in place.
  • Crankcase Explosions: Accumulation of oil mist in the crankcase can ignite if hot spots or sparks are present. Monitor crankcase pressure and ensure ventilation.
  • Heavy Lifting: Major component overhauls (cylinder heads, pistons) involve heavy lifting, requiring proper rigging and lifting gear.

Class survey

The class surveyor will typically focus on verifying the engine's structural integrity, operational safety, and compliance with statutory regulations (e.g., MARPOL Annex VI for Tier II emissions). Key checks include: 1. Review of Engine Logbooks & Maintenance Records: To confirm adherence to manufacturer's service schedules and proper recording of operational parameters and alarms. 2. Crankshaft Deflection Readings: To assess alignment and bearing condition, usually required annually or biennially. 3. Safety Device Functionality Tests: Witnessing tests for overspeed trip, low lube oil pressure shutdown, high cooling water temperature shutdown, and emergency stops. 4. Cylinder Head & Piston Spot Checks: During major overhauls, the surveyor may request opening of selected cylinder heads or pistons for visual inspection of liners, rings, valves, and injectors. 5. Bearing Clearances: Verification of main and connecting rod bearing clearances during major overhauls. 6. Fuel System Integrity: Inspection for leaks, proper filtration, and compliance with HFO handling requirements. 7. Lubrication Oil Analysis Reports: Review of trends in wear metals, TBN, and viscosity. 8. Exhaust Gas Emissions Compliance: Verification of engine's Tier II compliance through documentation and potentially on-site checks of engine settings or exhaust gas monitoring equipment if fitted. 9. General Engine Room Condition: Cleanliness, fire-fighting arrangements, and proper lagging of hot surfaces.

Estimated lifetime: 60,000 - 80,000 hours before major engine rebuild or replacement, with proper maintenance.

Need this part?

Request a quote for this model.

Free of charge — send us your request for HiMSEN equipment. Our team checks it and replies by e-mail.

For marine equipment hardly any maker or authorised dealer will name a price while the vessel is unknown. With the vessel details, availability and price can be settled faster; without them we may have to ask first, which costs a few days. If you are not allowed to name the vessel, a photo of the rating plate is enough — attach it below or send it as a reply to our confirmation e-mail.

Your contact details are not published. No account required.
Related models

Also in Main Engine 4-Stroke.

Other models of the same equipment type, HiMSEN first.

By manufacturer MAN Energy SolutionsWärtsiläCaterpillarHiMSENMTUVolvo PentaYanmar Power Technology Co., Ltd.HanshinDaihatsuPielstickMaK (Caterpillar)Rolls-Royce / BergenCaterpillar MaKCumminsBaudouinAll manufacturersSpare parts by equipmentNew here? Create a free account Can't read the plate? Try the nameplate scanner All HiMSEN models More like 8H27/38
More than the data sheet shows

We answer by e-mail, never with an automatic reply.

Tell us what you need for this HiMSEN 8H27/38 — a part, a service call, a second opinion. Are you HiMSEN? Claim this brand page.

Service engineer? Write the day report for this 8H27/38 in OceanSphere Work — photos, hours and parts, as a PDF for the owner. Try it free for 14 days →

Frequently asked

Questions that come up with this equipment.

Is this model's data free?

Yes. Specifications, documents and service notes for this model are readable without an account. An account adds saved searches and requests, nothing is taken away.

Can you find a part for this exact model?

Yes. Tell us the manufacturer, the model and what you need — a person reads every request and replies by e-mail.

The specifications look wrong — what now?

Send us the nameplate or the correct value. We check it against the manufacturer datasheet or class-society record and update the page.