OceanSphereENGINES

16W31

Main Engine 4-Stroke · Main Engines (4-Stroke)

Technical data from manufacturer or class sources · not yet verified by a person​‍​‍⁠‌‌⁠​⁠‌⁠‌⁠‍‌‌⁠‍⁠
9,760 kWPower
16Cylinders
310 mmBore
430 mmStroke

The Wärtsilä 16W31 is a medium‑speed, four‑stroke diesel main engine delivering about 9 760 kW at 750 rpm, notable for its common‑rail fuel injection and ability to run on HFO, MGO or approved biofuels.

Specifications

Technical data.

Do you have the manufacturer datasheet for this model? Send it with the enquiry form — we check it and name the source.

ConfigurationL
Speed (rpm)750
Fuel TypeHFO/MGO/Biofuel
TechnologyCommon Rail Tier III
Power (kW)9760
Inspection

Inspector Detail ✓ verified

Common issues

  • Piston ring wear and peeling, particularly under continuous low-load operation and with HFO, affecting chrome-ceramic rings.
  • Fuel injector nozzle coking, wear, or blockage due to fuel quality variations or high-pressure common rail system demands.
  • Turbocharger bearing wear or fouling of compressor/turbine blades, leading to reduced efficiency and potential damage.
  • Exhaust valve burning, seat wear, or sticking, especially when operating with HFO and frequent load changes.
  • Cylinder liner scuffing or excessive wear, often linked to lubrication issues, fuel quality, or improper combustion.
  • High-pressure common rail pump or pressure accumulator failures due to the extreme operating pressures and fuel contamination.
  • Engine Control System (ECS) sensor or actuator malfunctions, leading to performance issues or false alarms.
  • Main and connecting rod bearing wear, accelerated by poor lubrication, misalignment, or excessive load.

Inspection checklist

  • Fuel System Integrity: Check for leaks in high-pressure fuel lines, verify common rail pressure sensor readings, inspect fuel filter differential pressure and element condition. Ensure proper fuel changeover procedures are followed if operating on multiple fuels.
  • Lubricating Oil System: Monitor lube oil pressure and temperature, check filter differential pressure, and review recent oil analysis reports (TBN, viscosity, wear metals, water content). Inspect for external leaks.
  • Cooling Water System: Verify cooling water temperatures and pressures, inspect for leaks, and check inhibitor levels. Ensure heat exchangers are clean and free from fouling.
  • Exhaust Gas System & Turbocharger: Inspect turbocharger for excessive axial/radial play, signs of oil leakage, and casing cracks. Monitor exhaust gas temperatures per cylinder for consistency. Check exhaust manifold for leaks.
  • Cylinder Unit Condition (via indicator cocks/borescope): Look for piston crown deposits, assess cylinder liner condition (visual for scuffing/wear), and check exhaust valve condition (e.g., signs of burning, seat condition).
  • Engine Control System (ECS) & Alarms: Review engine alarm logs for recurring faults. Verify calibration of critical sensors (speed, pressure, temperature) and test actuator responses where possible.
  • Crankshaft Deflection: Perform crankshaft deflection readings as per manufacturer's schedule or class requirements, paying close attention to deviations indicating bearing wear or misalignment.
  • Engine Foundation & Mountings: Inspect all engine foundation bolts for tightness, signs of fretting, or corrosion. Check condition of resilient mountings if fitted.

Service intervals

Fuel filter elements (primary/secondary)500-1000 hours or as per differential pressure
Lube oil filter elements1000-2000 hours or as per differential pressure
Fuel injector overhaul/exchange4000-8000 hours
Exhaust valve overhaul/exchange8000-12000 hours
Cylinder unit overhaul (piston, rings, liner inspection)16000-24000 hours
Turbocharger overhaul (minor/major)12000-24000 hours
Main & connecting rod bearing inspection/renewal24000-32000 hours
Major overhaul (including crankshaft inspection)32000-48000 hours

Typical wear limits

Cylinder liner wear (max ovality/taper)0.6 - 0.8 mm
Piston ring gap (increase from new)0.5 - 1.0 mm (specific to ring type)
Exhaust valve seat recession0.5 - 1.0 mm (from original position)
Crankshaft deflection (max deviation between adjacent webs)0.05 - 0.10 mm
Connecting rod bearing clearance (increase from new)0.15 - 0.25 mm
Main bearing clearance (increase from new)0.20 - 0.30 mm
Turbocharger rotor axial/radial playAs per manufacturer's specific limits (typically 0.1-0.3 mm axial, 0.05-0.15 mm radial)

Ranges are typical for this design class. Always confirm against the manufacturer documentation for your serial number.

Critical spares

  • Complete fuel injector unit (at least one per cylinder type)
  • Full set of piston rings for at least one cylinder
  • Exhaust valve spindle and seat ring (at least one set)
  • High-pressure fuel pump element or repair kit (for common rail system)
  • Complete set of fuel filter elements (all stages)
  • Complete set of lubricating oil filter elements
  • Turbocharger bearing cartridge or repair kit
  • Critical ECS sensors (e.g., engine speed, common rail pressure, exhaust gas temperature thermocouple)

Safety

  • High-Pressure Fuel Leaks: Common rail systems operate at extremely high pressures (up to 2000+ bar). Leaks can atomize fuel, creating an invisible, highly flammable spray that poses a severe fire and explosion risk.
  • Hot Surfaces: Exhaust manifolds, turbochargers, and engine block surfaces operate at high temperatures, posing a significant burn hazard. Ensure insulation is intact.
  • Rotating Machinery: Exposed rotating components (flywheel, PTO, turbocharger rotor) present entanglement and crushing hazards. Ensure guards are in place.
  • Crankcase Explosions: Although modern engines have safety devices (e.g., oil mist detectors, relief valves), the risk of crankcase explosions due to hot spots or bearing failures remains. Respond immediately to oil mist detector alarms.
  • Noise Levels: Engine room noise levels are typically high, requiring mandatory hearing protection to prevent permanent hearing damage.

Class survey

Class surveyors will typically focus on verifying the engine's overall condition, adherence to planned maintenance schedules, and the functionality of safety systems. Key checks include: review of engine running hours and maintenance records; verification of overspeed trip, low lube oil pressure, and high cooling water temperature shutdowns; crankshaft deflection readings; inspection of main and connecting rod bearings (during major overhauls or spot checks); cylinder liner wear measurements and piston crown inspection; exhaust valve condition; integrity of the high-pressure fuel system, including leak-off arrangements; turbocharger inspection (bearings, rotor, casing); and the condition of engine foundation and mounting arrangements. Compliance with relevant emission regulations (e.g., Tier III for NOx) and associated monitoring equipment will also be verified.

Estimated lifetime: 60,000 - 80,000 hours before major overhaul (e.g., crankshaft removal), with proper maintenance and intermediate overhauls.

Need this part?

Request a quote for this model.

Free of charge — send us your request for Wärtsilä equipment. Our team checks it and replies by e-mail.

For marine equipment hardly any maker or authorised dealer will name a price while the vessel is unknown. With the vessel details, availability and price can be settled faster; without them we may have to ask first, which costs a few days. If you are not allowed to name the vessel, a photo of the rating plate is enough — attach it below or send it as a reply to our confirmation e-mail.

Your contact details are not published. No account required.
Related models

Also in Main Engine 4-Stroke.

Other models of the same equipment type, Wärtsilä first.

By manufacturer MAN Energy SolutionsWärtsiläCaterpillarHiMSENMTUVolvo PentaYanmar Power Technology Co., Ltd.HanshinDaihatsuPielstickMaK (Caterpillar)Rolls-Royce / BergenCaterpillar MaKCumminsBaudouinAll manufacturersSpare parts by equipmentNew here? Create a free account Can't read the plate? Try the nameplate scanner All Wärtsilä models More like 16W31
More than the data sheet shows

We answer by e-mail, never with an automatic reply.

Tell us what you need for this Wärtsilä 16W31 — a part, a service call, a second opinion. Are you Wärtsilä? Claim this brand page.

Service engineer? Write the day report for this 16W31 in OceanSphere Work — photos, hours and parts, as a PDF for the owner. Try it free for 14 days →

Frequently asked

Questions that come up with this equipment.

Is this model's data free?

Yes. Specifications, documents and service notes for this model are readable without an account. An account adds saved searches and requests, nothing is taken away.

Can you find a part for this exact model?

Yes. Tell us the manufacturer, the model and what you need — a person reads every request and replies by e-mail.

The specifications look wrong — what now?

Send us the nameplate or the correct value. We check it against the manufacturer datasheet or class-society record and update the page.