OceanSphereENGINES

10W31

Main Engine 4-Stroke · Main Engines (4-Stroke)

Technical data from manufacturer or class sources · not yet verified by a person​‍​‍⁠‌‌⁠​​⁠‍​‍​​‌​‍⁠
6,100 kWPower
10Cylinders
310 mmBore
430 mmStroke

The Wärtsilä 10W31 is a medium‑speed, inline 10‑cylinder, four‑stroke diesel engine delivering about 6 100 kW at 750 rpm, noted for its high power density and flexible fuel capability (HFO, MGO, biofuel and dual‑fuel LNG).

Specifications

Technical data.reference — unverified

Do you have the manufacturer datasheet for this model? Send it with the enquiry form — we check it and name the source.

Cylinder power610 kW/cyl (diesel)
Mean effective pressure (BMEP)30 bar
SFOC (diesel)167.7 g/kWh (optimal point)
Weight (8V31)~57.1 tonnes (dry, diesel)
Weight (16V31)~89–92.5 tonnes (dry, diesel)
Piston speed10.75 m/s
TurbochargingTwo-stage turbocharging with intercooling
Fuel injectionCommon rail direct injection
Valve layout2 inlet, 2 exhaust valves per cylinder
ConfigurationL
Speed (rpm)750
Fuel TypeHFO/MGO/Biofuel
TechnologyCommon Rail Tier III
Power (kW)6100
Inspection

Inspector Detail ✓ verified

Common issues

  • Carbon deposit accumulation in cylinders, turbocharger, and exhaust system, primarily due to prolonged low-load operation or suboptimal combustion.
  • Common Rail injector nozzle wear, clogging, or leakage, leading to poor fuel atomization, increased fuel consumption, and potential cylinder damage.
  • Exhaust valve burning or seat wear, particularly when operating on HFO, exacerbated by low-load conditions or incorrect valve timing/clearance.
  • Turbocharger fouling (compressor and turbine sides) and bearing wear, impacting engine efficiency and boost pressure.
  • Piston ring sticking or breakage, resulting in increased blow-by, higher lube oil consumption, and potential liner scuffing.
  • Main and connecting rod bearing wear, often indicated by increased clearances or abnormal lube oil analysis results.
  • High-pressure fuel system leakages (Common Rail), posing significant safety and operational risks.

Inspection checklist

  • Cylinder Unit Condition: Conduct endoscopic inspection of combustion chambers (piston crown, liner, valves) for carbon deposits, scuffing, burning, and general wear. Check for signs of blow-by.
  • Fuel Injection System Integrity: Visually inspect common rail pipes, high-pressure pumps, and injectors for any signs of leakage, proper securing, and external damage. Verify fuel pressure readings against manufacturer specifications.
  • Turbocharger Health: Check axial and radial play of the turbocharger shaft. Inspect compressor and turbine blades for fouling, erosion, or damage. Monitor bearing temperatures and boost pressure.
  • Exhaust Gas System & Valves: Inspect exhaust manifold for leaks. Monitor individual cylinder exhaust gas temperatures (EGTs) for balance. If accessible, check exhaust valve condition and seat integrity.
  • Lube Oil System: Verify correct lube oil pressure and temperature. Review recent lube oil analysis reports for wear metals, TBN, viscosity, and water content. Inspect lube oil filters for contamination.
  • Cooling Water System: Inspect for leaks in pipes, pumps, and heat exchangers. Verify correct cooling water pressure and temperature. Check cooling water treatment levels and condition.
  • Engine Performance Parameters: Compare current engine parameters (power, RPM, fuel consumption, EGTs, boost pressure, cylinder pressures) against baseline data and manufacturer's specifications.
  • Safety Devices Functionality: Test the functionality of critical safety devices including overspeed trip, low lube oil pressure shutdown, high cooling water temperature shutdown, and emergency stops.

Service intervals

Fuel Injector Overhaul6,000 - 12,000 running hours
Exhaust Valve Overhaul6,000 - 12,000 running hours
Piston Ring Renewal12,000 - 24,000 running hours
Cylinder Head Overhaul12,000 - 24,000 running hours
Turbocharger Overhaul12,000 - 24,000 running hours
Main & Connecting Rod Bearing Inspection24,000 - 36,000 running hours
Major Engine Overhaul48,000 - 72,000 running hours

Typical wear limits

Cylinder Liner Ovality/TaperTypically 0.6 - 0.8 mm maximum deviation from nominal bore.
Piston Ring End GapMaximum allowable increase, often 2-3 times the new ring gap specified by manufacturer.
Main & Connecting Rod Bearing ClearancesMaximum allowable increase, typically 0.15 - 0.2 mm over nominal clearance.
Crankshaft DeflectionMaximum allowable deviation typically 0.05 - 0.1 mm across webs, depending on engine size and manufacturer.
Exhaust Valve Seat RecessionMaximum allowable depth, typically 1.5 - 2.0 mm from cylinder head face.

Ranges are typical for this design class. Always confirm against the manufacturer documentation for your serial number.

Critical spares

  • Complete Fuel Injector Assembly (at least one per cylinder type)
  • Exhaust Valve Spindle and Seat Ring (one set per cylinder)
  • Full Set of Piston Rings (for one cylinder)
  • Cylinder Head Gasket Set (for one cylinder)
  • Turbocharger Bearing Cartridge / Repair Kit
  • High-Pressure Fuel Pump Element or Common Rail Pressure Sensor
  • Main Bearing Shells (one complete set)
  • Connecting Rod Bearing Shells (one complete set)

Safety

  • High-Pressure Fuel System (Common Rail): Extreme caution is paramount. Fuel pressures up to 2000+ bar pose a severe risk of fuel spray ignition and penetration injuries from even pinhole leaks. Always ensure system is depressurized before any work.
  • Hot Surfaces: Exhaust manifold, turbocharger, and other engine components operate at very high temperatures. Risk of severe burns. Ensure proper insulation and use appropriate PPE.
  • Rotating Machinery: Crankshaft, flywheel, and turbocharger rotate at high speeds. Ensure engine is positively stopped, secured, and 'Permit to Work' procedures are strictly followed before any intervention.
  • Pressurized Systems: Cooling water, lube oil, starting air, and fuel systems are under pressure. Always depressurize relevant systems before opening any connections or components.
  • Crankcase Explosions: While rare, the potential for crankcase explosion exists if oil mist concentration is high and an ignition source is present. Ensure proper crankcase ventilation and oil mist detection systems are functional.

Class survey

For the Wärtsilä 10W31, a class surveyor will typically focus on: 1. Documentation Review: Thorough scrutiny of engine logbooks, maintenance records, lube oil analysis reports, and previous survey reports to verify compliance with planned maintenance and operational parameters. 2. Crankshaft Deflection Measurement: Verification of readings against manufacturer's limits, typically required at specific intervals (e.g., every 12,000-24,000 hours) to assess crankshaft alignment and bearing condition. 3. Main & Connecting Rod Bearing Inspection: Opening up a representative number of bearings for visual inspection and clearance measurement, as per planned maintenance system or class requirements (e.g., alternating sets every 24,000-36,000 hours). 4. Cylinder Unit Condition Assessment: Endoscopic inspection of liners, pistons, and valves. Physical inspection during overhaul if due, focusing on wear, carbon build-up, and scuffing. 5. Safety Devices Functionality: Witnessing the testing of critical safety devices including overspeed trip, low lube oil pressure shutdown, high cooling water temperature shutdown, and emergency stops. 6. Fuel System Integrity: Close inspection of the common rail system for leaks, proper securing, and condition of high-pressure components, given the inherent risks. 7. Engine Performance Verification: Review of engine parameters (EGTs, boost pressure, fuel consumption, cylinder pressures) to ensure stable, efficient, and safe operation within design limits. 8. Emission Compliance: Verification of exhaust gas treatment systems (if applicable for specific installations) and records for compliance with IMO Tier III regulations.

Estimated lifetime: 48,000 - 72,000 running hours before major overhaul (design life often exceeding 100,000 hours with proper maintenance)

Need this part?

Request a quote for this model.

Free of charge — send us your request for Wärtsilä equipment. Our team checks it and replies by e-mail.

For marine equipment hardly any maker or authorised dealer will name a price while the vessel is unknown. With the vessel details, availability and price can be settled faster; without them we may have to ask first, which costs a few days. If you are not allowed to name the vessel, a photo of the rating plate is enough — attach it below or send it as a reply to our confirmation e-mail.

Your contact details are not published. No account required.
Related models

Also in Main Engine 4-Stroke.

Other models of the same equipment type, Wärtsilä first.

By manufacturer MAN Energy SolutionsWärtsiläCaterpillarHiMSENMTUVolvo PentaYanmar Power Technology Co., Ltd.HanshinDaihatsuPielstickMaK (Caterpillar)Rolls-Royce / BergenCaterpillar MaKCumminsBaudouinAll manufacturersSpare parts by equipmentNew here? Create a free account Can't read the plate? Try the nameplate scanner All Wärtsilä models More like 10W31
More than the data sheet shows

We answer by e-mail, never with an automatic reply.

Tell us what you need for this Wärtsilä 10W31 — a part, a service call, a second opinion. Are you Wärtsilä? Claim this brand page.

Service engineer? Write the day report for this 10W31 in OceanSphere Work — photos, hours and parts, as a PDF for the owner. Try it free for 14 days →

Frequently asked

Questions that come up with this equipment.

Is this model's data free?

Yes. Specifications, documents and service notes for this model are readable without an account. An account adds saved searches and requests, nothing is taken away.

Can you find a part for this exact model?

Yes. Tell us the manufacturer, the model and what you need — a person reads every request and replies by e-mail.

The specifications look wrong — what now?

Send us the nameplate or the correct value. We check it against the manufacturer datasheet or class-society record and update the page.