OceanSphereENGINES

8W38

Main Engine 4-Stroke · Main Engines (4-Stroke)

Technical data from manufacturer or class sources · not yet verified by a person​‍​‍⁠‌‌‌​‌​⁠⁠‌⁠⁠⁠​⁠‍
5,800 kWPower
8Cylinders
380 mmBore
475 mmStroke

The Wärtsilä 8W38 is an inline, medium‑speed (600 rpm) four‑stroke diesel main engine delivering approximately 5 800 kW, designed for direct mechanical drive of ship propellers using heavy fuel oil or marine gasoil.

Specifications

Technical data.

Do you have the manufacturer datasheet for this model? Send it with the enquiry form — we check it and name the source.

ConfigurationL
Speed (rpm)600
Fuel TypeHFO/MGO
TechnologyMechanical
Power (kW)5800
Inspection

Inspector Detail ✓ verified

Common issues

  • Cold Corrosion of Cylinder Liners: Sulfuric acid formation from high sulfur fuel and low liner temperatures, leading to increased wear and potential scuffing.
  • Exhaust Valve Burning and Seat Wear: Common with HFO operation, poor fuel quality, incorrect timing, or insufficient cooling, leading to gas leakage and reduced efficiency.
  • Fuel Injector Nozzle Coking and Wear: Results in poor fuel atomization, incomplete combustion, increased thermal stress on cylinder components, and higher fuel consumption.
  • Piston Ring Wear/Breakage and Piston Groove Wear: Leads to increased blow-by, higher lube oil consumption, and potential piston seizure.
  • Turbocharger Fouling and Bearing Degradation: Reduces engine efficiency, increases exhaust back pressure, and can lead to catastrophic turbocharger failure if bearings fail.
  • Main and Connecting Rod Bearing Wear: Caused by lube oil contamination, insufficient lubrication, or crankshaft misalignment, leading to increased clearances and potential damage.
  • Fuel Pump Element Wear: Affects injection pressure and timing, leading to poor combustion and reduced engine performance.
  • Cooling System Fouling and Corrosion: Reduces heat transfer efficiency, leading to localized hot spots and potential thermal stress on components.

Inspection checklist

  • Cylinder Liner Wear Measurement: Check for ovality and wear rates, especially at the top dead center (TDC) position. Compare with manufacturer's limits.
  • Exhaust Valve Condition: Visual inspection for burning, pitting, and seat integrity (via endoscope or during overhaul). Check valve rotator functionality.
  • Fuel Injector Spray Pattern and Pressure Test: Verify correct atomization and opening pressure (typically 300-350 bar for mechanical injectors).
  • Piston Crown and Ring Pack Inspection: Check for carbon build-up, ring freedom in grooves, and groove wear (during piston withdrawal).
  • Turbocharger Bearing Play and Rotor Condition: Measure axial and radial play. Inspect compressor and turbine sides for fouling, erosion, or foreign object damage.
  • Crankshaft Deflection Readings: Monitor regularly for changes indicating bearing wear, foundation issues, or alignment problems. Max deviation typically 0.05-0.10 mm.
  • Lube Oil Analysis (S.O.P.): Regular checks for wear metals, TBN, viscosity, water content, fuel dilution, and insolubles.
  • Fuel System Integrity: Inspect high-pressure fuel lines for leaks, proper shielding, and alarm functions. Verify fuel oil viscosity and temperature control.
  • Cooling Water System: Check for leaks, pressure, temperature, and water treatment parameters (e.g., pH, chloride, nitrite levels).
  • Safety Devices and Alarms: Test overspeed trip, low lube oil pressure shutdown, high cooling water temperature alarm/shutdown, and exhaust gas temperature alarms.

Service intervals

Fuel Injector Overhaul3,000 - 6,000 running hours
Exhaust Valve Overhaul6,000 - 12,000 running hours (depending on fuel quality and operation)
Piston Overhaul (withdrawal, ring replacement, groove check)12,000 - 18,000 running hours
Turbocharger Minor Overhaul (cleaning, bearing check)12,000 - 18,000 running hours
Turbocharger Major Overhaul (full strip-down, balancing)24,000 - 36,000 running hours
Connecting Rod Bearing Inspection/Renewal18,000 - 24,000 running hours
Main Bearing Inspection/Renewal36,000 - 48,000 running hours
Major Engine Overhaul (full strip-down, component renewal)72,000 - 96,000 running hours

Typical wear limits

Cylinder Liner Max Wear (at TDC)0.6 - 0.8 mm
Piston Ring Groove Max Axial Wear0.15 - 0.25 mm (depending on groove position)
Crankshaft Deflection Max (between adjacent throws)0.05 - 0.10 mm
Main Bearing Max Clearance0.40 - 0.50 mm
Connecting Rod Bearing Max Clearance0.35 - 0.45 mm
Exhaust Valve Seat Recess Max1.5 - 2.0 mm (from nominal position)

Ranges are typical for this design class. Always confirm against the manufacturer documentation for your serial number.

Critical spares

  • Complete Fuel Injector Assembly (at least one per cylinder type)
  • Complete Exhaust Valve Assembly (or valve spindle and seat ring)
  • Set of Piston Rings (for at least one cylinder)
  • Main Bearing Shells (one complete set)
  • Connecting Rod Bearing Shells (one complete set)
  • Fuel Pump Element (one per cylinder type)
  • Turbocharger Bearing Cartridge (or complete rotor assembly)
  • Critical Gaskets and O-rings (e.g., cylinder head, liner sealing, fuel/lube oil lines)
  • Starting Air Valve (one complete assembly)

Safety

  • High-Pressure Fuel Leaks: Risk of fire/explosion, especially with HFO. Ensure proper shielding and leakage detection.
  • Hot Surfaces: Exhaust manifold, turbocharger, cylinder heads, and steam/thermal oil lines pose severe burn hazards. Ensure insulation integrity.
  • Rotating Machinery: Flywheel, coupling, and shafting present entanglement risks. Ensure guards are in place.
  • Starting Air System: High-pressure air (typically 30 bar) can cause severe injury or death if pipes rupture or components fail. Verify safety valves and pipe integrity.
  • Heavy Lifting Operations: During maintenance, there is a risk of crushing injuries from heavy components (cylinder heads, pistons, connecting rods). Ensure proper lifting gear and procedures.
  • Confined Space Entry: Crankcase or exhaust ducts may have oxygen depletion or toxic gas accumulation. Follow strict permit-to-work procedures.

Class survey

During class surveys (annual, intermediate, special), surveyors typically focus on: 1. Operational Test: Verification of engine starting, stopping, reversing, load response, and emergency stops from bridge and engine control room. 2. Safety Devices: Testing of overspeed trip, low lube oil pressure shutdown, high cooling water temperature alarm/shutdown, and exhaust gas temperature alarms. 3. Fuel System Integrity: Inspection of high-pressure fuel lines for leaks, proper shielding, and fuel oil leakage detection system functionality. Verification of fuel oil viscosity and temperature control. 4. Exhaust Gas System: Check for leaks, insulation integrity, and spark arrestor condition. 5. Crankcase Safety: Verification of crankcase oil mist detector (OMD) functionality and alarm settings. Inspection of crankcase relief valves. 6. Steering Gear Interface: Confirmation of main engine power availability for steering gear operation. 7. Documentation Review: Examination of engine logbooks, maintenance records, lube oil analysis reports, and spare parts inventory for compliance and trends. 8. Visual Inspection: General condition of the engine, foundations, piping, wiring, and overall cleanliness of the engine room. 9. Emergency Systems: Confirmation of emergency generator start and load transfer, and emergency lighting in the engine room.

Estimated lifetime: 80,000 - 120,000 hours before major life extension overhaul, with continuous maintenance and component renewal. Well-maintained units can exceed this significantly.

Need this part?

Request a quote for this model.

Free of charge — send us your request for Wärtsilä equipment. Our team checks it and replies by e-mail.

For marine equipment hardly any maker or authorised dealer will name a price while the vessel is unknown. With the vessel details, availability and price can be settled faster; without them we may have to ask first, which costs a few days. If you are not allowed to name the vessel, a photo of the rating plate is enough — attach it below or send it as a reply to our confirmation e-mail.

Your contact details are not published. No account required.
Related models

Also in Main Engine 4-Stroke.

Other models of the same equipment type, Wärtsilä first.

By manufacturer MAN Energy SolutionsWärtsiläCaterpillarHiMSENMTUVolvo PentaYanmar Power Technology Co., Ltd.HanshinDaihatsuPielstickMaK (Caterpillar)Rolls-Royce / BergenCaterpillar MaKCumminsBaudouinAll manufacturersSpare parts by equipmentNew here? Create a free account Can't read the plate? Try the nameplate scanner All Wärtsilä models More like 8W38
More than the data sheet shows

We answer by e-mail, never with an automatic reply.

Tell us what you need for this Wärtsilä 8W38 — a part, a service call, a second opinion. Are you Wärtsilä? Claim this brand page.

Service engineer? Write the day report for this 8W38 in OceanSphere Work — photos, hours and parts, as a PDF for the owner. Try it free for 14 days →

Frequently asked

Questions that come up with this equipment.

Is this model's data free?

Yes. Specifications, documents and service notes for this model are readable without an account. An account adds saved searches and requests, nothing is taken away.

Can you find a part for this exact model?

Yes. Tell us the manufacturer, the model and what you need — a person reads every request and replies by e-mail.

The specifications look wrong — what now?

Send us the nameplate or the correct value. We check it against the manufacturer datasheet or class-society record and update the page.