"> Furuno Furuno DS-890 Speed/Depth
⚓ Working on this equipment?
Ask the AI troubleshooter, log your hours on board and turn them into invoice-ready service reports — for this exact model.
Start free — 14 days →
No credit card required
🔧 127 verified suppliers & service companies for Furuno in the Maritime Network Find suppliers →
Furuno

Furuno DS-890 Speed/Depth

Furuno Furuno DS-890 Speed/Depth is identified in the source list as a marine echo sounder. It is installed on the bridge and at the associated antenna, transducer, camera or sensor location, with data distributed to connected ship systems as required. Its purpose is to measure water depth beneath the vessel using an acoustic transducer and bridge display. The source record provides no additional model-specific operating figure beyond the listed designation and category. The exact sensor set, recording functions, data interfaces, approval status and redundancy depend on the installed model. The exact model designation distinguishes sensing, recording or communication capability from neighboring bridge equipment; refer to the manufacturer documentation for the exact figure.

Components & Design

Component data being added…

Technical Data

imo compliant True
combined speed depth True

🤖 Ask about this model

One free question — answered like a marine engineer. No account needed.

Common failures & inspection points

Transducer fouling, damage or aeration caused by marine growth, paint, impact or hull-flow conditions, resulting in weak, intermittent or incorrect depth returns
Power-supply failure caused by breaker, converter or wiring faults, resulting in loss of the equipment or repeated restarts
Network or interface failure caused by damaged cabling, port faults or configuration changes, resulting in loss of data to connected systems
Display, processor or control failure caused by hardware or software faults, resulting in frozen indications, alarms or unavailable functions
Incorrect configuration or time, position or sensor input caused by setup or upstream faults, resulting in misleading or incomplete information

Service & Maintenance

Inspect sensors, antennas, transducers, cameras, cabling, power supplies and network interfaces applicable to the installed equipment. Compare displayed information with independent references where possible and investigate recurring alarms or missing channels. Verify required outputs to other bridge systems and preserve configuration before approved software or hardware maintenance. Clean exposed sensors and optical surfaces without damaging coatings or seals. Check backup power or recording arrangements where applicable. Refer to the manufacturer documentation for the exact figure for test, calibration, update and recovery procedures.

Suppliers & Spare Parts

Direct links to manufacturer, datasheet, spare-parts portal and dealers — request access below.

📄 Request sourcing links & documents
🛠 Manage this equipment in your fleet

Cases, daily reports, timesheets and AI troubleshooting in the OceanSphere Marine app — free for 14 days.

Start free trial →
🔎 Suppliers & service for this equipment

Find manufacturers, repair shops and spare-part dealers in the Maritime Network — our global company directory.

Maritime Network →

Replacement Parts

Keep fuses, selected power-supply and interface modules, cables or connectors, storage media where applicable and manufacturer-recommended sensor or electronic spares. Replacement core units must remain compatible with the approved bridge installation. Preserve configuration and recorded setup data.
Equipment Model #142275 · ✓ still in production

Wer liefert dieses Teil? 178 Betriebe im Verzeichnis · 9 aus Herstellerlisten

Aqua Marine Electronics
Piraeus, Greece
✓ autorisiert
Avatec Marine BV
Dalweg 3B 3233 KK Oostvoorne Rotterdam, Netherlands
✓ autorisiert
Bluetek Supply
Miami, United States
✓ autorisiert
Furuno Italia S.r.l.
Gatteo, Italy
✓ autorisiert
HORA ELEKTRONIK d.o.o.
A.B. Simica 65, Croatia
✓ autorisiert
JN TAYLOR & CO. PTY LTD
Australia
✓ autorisiert
Lammers Schiffselektronik GmbH
Leer, Germany
✓ autorisiert
RADIO HOLLAND EGYPT
Alexandria, Egypt
✓ autorisiert
Alfa International (Marine Electronics)
Karachi, Pakistan
Marine Technics Baltia OÜ
Tallinn, Estonia
Navtronics
Marbella, Spain
Scan Marine Inc.
Tondo, Manila, Philippines
Weitere aus Hersteller- und Marktplatzverzeichnissen:
C. Sahamongkol Engineering Ltd., Part. · ThailandFuruno Danmark · DenmarkFuruno Norge A/S · NorwayMarine Communications MARCOM · Trinidad And TobagoOzsay Bulgaria Marine Electronics Ltd. · BulgariaProesa Electronica | Marine Electronics & Solutions · MexicoQueens Radio Electronics Marine Pte. Ltd. · Sri LankaMosaic Business Corporation · CameroonSeacom Marine (B) Sdn Bhd · Brunei Darussalam
Alle Betriebe für Furuno ansehen →