"> Alfa Laval Reverse Osmosis Unit 2m3h Alfa Marine
⚓ Working on this equipment?
Ask the AI troubleshooter, log your hours on board and turn them into invoice-ready service reports — for this exact model.
Start free — 14 days →
No credit card required
🔧 114 verified suppliers & service companies for Alfa Laval in the Maritime Network Find suppliers →
Alfa Laval

Reverse Osmosis Unit 2m3h Alfa Marine

Alfa Laval Reverse Osmosis Unit 2m3h Alfa Marine is identified in the source list as a reverse osmosis unit. It is installed in the freshwater or process-water treatment system between source water, storage and the intended consumers. Its purpose is to condition, disinfect, soften, mineralize, desalinate or convey sanitary waste according to the listed treatment process. The source record provides the existing record note '2 m³/h capacity'. Filters, chemical dosing, ultraviolet lamps, membranes, softening media, pumps, valves, vacuum equipment, sensors and controls may be included depending on the process. The exact model designation and any source-listed capacity distinguish process size and treatment arrangement from neighboring water-treatment units; refer to the manufacturer documentation for the exact figure.

Alfa Laval Reverse Osmosis Unit 2m3h Alfa Marine

Components & Design

Component data being added…

Technical Data

capacity m3h 2
treatment type Reverse Osmosis Unit

🤖 Ask about this model

One free question — answered like a marine engineer. No account needed.

Common failures & inspection points

Reduced treatment or sanitary performance caused by fouled filters, exhausted media, scaled membranes, aged lamps or blocked piping, resulting in poor water quality, low flow or system alarms
Dosing, regeneration or vacuum failure caused by empty chemical supply, pump faults, air leakage or control errors, resulting in incorrect water chemistry or poor sanitary operation
Sensor or conductivity fault caused by fouling, calibration drift or wiring problems, resulting in implausible readings or alarms
Pump or valve failure caused by wear, blockage or electrical faults, resulting in low treatment flow or inability to route water correctly
Leakage caused by seal, housing, membrane or piping deterioration, resulting in water loss, vacuum loss or unstable process conditions

Service & Maintenance

Inspect filters, membranes, lamps, dosing equipment, softener vessels, pumps, valves, vacuum equipment, sensors and sample points as applicable to the installed process. Maintain hygienic conditions during opening of potable-water treatment equipment. Trend pressure, vacuum and water-quality indications and investigate abnormal values promptly. Verify alarms, regeneration, diversion, flushing or shutdown functions after maintenance. Store chemicals and treatment media according to approved procedures. Refer to the manufacturer documentation for the exact figure for dosing, replacement, cleaning and operating settings.

Suppliers & Spare Parts

Direct links to manufacturer, datasheet, spare-parts portal and dealers — request access below.

📄 Request sourcing links & documents
🛠 Manage this equipment in your fleet

Cases, daily reports, timesheets and AI troubleshooting in the OceanSphere Marine app — free for 14 days.

Start free trial →
🔎 Suppliers & service for this equipment

Find manufacturers, repair shops and spare-part dealers in the Maritime Network — our global company directory.

Maritime Network →

Replacement Parts

Keep filter elements, membrane or lamp components, approved treatment media, dosing-pump or vacuum-system service parts, seals, valves, sensors and sampling consumables recommended for the installed process. Chemicals must be approved for the intended water service. Confirm exact replacement parts against unit configuration.
Equipment Model #122212 · ✓ still in production

Wer liefert dieses Teil? 17 Betriebe im Verzeichnis · 22 aus Herstellerlisten

ALFA LAVAL
Sweden
✓ autorisiert
Alfa Laval Aalborg Oy
Denmark
✓ autorisiert
MACOR
France
✓ autorisiert
CHIEFMAR SRL
Genova, Italy
Fluid Global Solutions S.r.l.
Arcola, Italy
HAGEDORN Products & Systems GmbH
Hemmoor, Germany
HSM Marine Engineering Pte Ltd
Singapore, Singapore
KET Marine BV
Netherlands
Mares Shipping GmbH
Hamburg, Germany
Marine Technic A/S
Naestved, Denmark
Mistral Marine Solutions
Switzerland
Seaway Marine Trading BV
Vlaardingen, Netherlands
Weitere aus Hersteller- und Marktplatzverzeichnissen:
Global Services (Europe) Ltd · United KingdomA. Nobel en Zn. - Filtration & Separation B.V. (Headquarters) · NetherlandsCOOL DYNAMIC - D. GKOUSKOS · GreeceDingbro Ltd Industrial Filtration Division · United KingdomDitco Worldwide Shipsuppliers · NetherlandsEberhardt Agencies ApS · DenmarkEfemarinmotor · TurkeyFamous World Int.Holdings Ltd · ChinaFlorijn Ship Spares · NetherlandsGLINAR Turbo&Diesel · United KingdomGoodwill Industrial Solution Ltd. · TaiwanHMS Hanseatic Marine Services (HQ) · Germany
Alle Betriebe für Alfa Laval ansehen →